PS:1 Wiki Dev - User contributions [en]

Epilog 30w Mini 24 Laser Engraver

2016-01-15T21:18:26Z

Andrewd: /* List of Currently Certified Users */

{{ Template:EquipmentPage
| owner=PS:One
| model=Mini 24
| serial=SERIAL NUMBER
| arrived=6/29/2011
| doesitwork=yes
| contact=[[CNC|CNC Area Host]]
| where=Shock Shop
| certification=yes
| hackable=no
| value=$15,000
| image = Epilog_fired_the_laser.jpg
| hostarea = CNC
}}

== Status ==

Up and running, doing just fine. Uses the inline exhaust fan through the roof; the fume extractor is not currently being used with the laser.

[[Epilog/Epilog service notes]] - please note any service, repairs, or adjustments you make to the machine

== Top Eight ==
* Don't use the autofocus, because it could burn out a motor.
* Don't cut materials that will ignite or emit dangerous fumes (any chlorinated plastic like PVC, for example). See section below.
* Always use the exhaust fan/always use the air assist on vector cuts.
* You must stay with the job; don't walk away. Things could catch on fire, that would suck.
* Sometimes it's a pain to get the right driver working. http://www.thinkgeek.com/product/11c3/
* Do not attempt to service the machine yourself unless you've cleared it with the CNC Area Host
* Do not touch any settings in the Config menu on the machine itself
* Do not touch any settings in the Maint menu on the machine itself '''''except''''' you may use Maint/1/Return Home to reset the cutting head to the machine's default origin (<.015" inside the top left corner as of 8/8/15)

== General Info ==

This machine: http://www.epiloglaser.com/mini24_overview.htm

Manual for this machine: http://www.epiloglaser.com/downloads/pdf/mini_helix_4.22.10.pdf

[[laser settings|Settings for various materials]]

[[Laser Cutter Instructions and Workflow]]

Cleaning the optics: http://www.epiloglaser.com/tl_clean_optics.htm

Inkscape for newbies: http://blog.ponoko.com/2008/01/21/how-to-inkscape-for-ponoko-newbies-trace-an-image/

Experiment with [[Laser settings]] to find the lowest possible power and highest possible speed to get clean vector cuts. The new optics and tube (as of December 2014) can cut many organic materials with a minimum of charring.

== Ventilation ==

'''Always''' turn on the exhaust fan using the switch located in the silver box to the left of the machine.

== Air assist ==

Turn on the air assist by turning the silver knob on the regulator located on the red bracket attached to the left of the machine. The pressure regulator has no adjustable settings. It is either on or off.

Air assist is used for vector cutting to have nice traces and avoid your material to burn. However some people like to have it disabled for raster jobs.

Turn air assist off when you've finished and you don't need it while doing your settings.

Check the regulator for accumulated water from time to time. Place a container (and maybe some paper towels) under the regulator and vent accumulated water from the bottom using the small petcock. If too much water accumulates in the regulator, it may flow through the air hose and into the machine, spraying onto the bed/material.

== Cleanup ==

Please leave the machine cleaner than you found it by emptying the crumb tray below the cutting table, picking up cutouts, and vacuuming up any acrylic dust you made.

== Troubleshooting ==

Under construction.

== '''NEVER CUT THESE MATERIALS''' ==

* '''PVC (Poly Vinyl Chloride):''' Also known as '''"vinyl"''' '''"pleather"''' or '''"artificial leather."''' Most adhesive vinyl shelf paper (e.g. Con-Tact Paper) also is PVC. Emits HCl and nasty chlorinated compounds when cut! Don't ever cut this material as it will ruin the optics, cause the metal of the machine to corrode, and ruin the motion control system.
* '''Polycarbonate:''' Also known as '''"Lexan."''' Polycarbonate is also often found as flat, sheet material. The case cover window on the laser cutter is made of Polycarbonate because polycarbonate strongly absorbs infrared radiation! This is the frequency of light the laser cutter uses to cut materials, so it is very ineffective at cutting polycarbonate. Polycarbonate can also emit flame and chlorine gas when cut, making it a poor choice for laser cutting.
* '''ABS:''' ABS does not cut well in a laser cutter. It tends to melt rather than vaporize, and has a higher chance of catching on fire and leaving behind melted gooey deposits on the vector cutting grid. It also does not engrave well (again, tends to melt). Finally, ABS emits cyanide when cut.
* '''HDPE:''' "milk bottle" plastic. It melts. It gets gooey. It catches on fire. Don't use it.
* '''PolyStyrene Foam:''' It catches fire, it melts, and only thin pieces cut. This is the #1 material that causes laser fires!!!
* '''Fiberglass:''' The epoxy resin used in fiberglass is bad to cut, the vapor/fumes of the epoxy resin are bad. The fiberglass mat itself, without resin, is safe to cut.
* '''Coated Carbon Fiber:''' Thin carbon fiber mat can be cut, with some fraying. However, once coated with epoxy it will emit noxious fumes.
* Silhouette '''magnet paper''' (sold by Inventables by example): it likely contains chlorine. Emits HCl and nasty chlorinated compounds when cut! Don't ever cut this material as it will ruin the optics, cause the metal of the machine to corrode, and ruin the motion control system.
* '''PTFE:''', also known as '''Teflon''' or any fluorinated polymer it will releases nasty fluorinated compounds (bad for you) and sublimate then deposit on the lenses (likely destroying them).
* '''Gator foam''': foam core gets burned and eaten away compared to the top and bottom hard paper shell. Not a fantastic thing to cut, but it can be cut if watched. And the MSDS sheet says it may produce hydrogen bromide and hydrogen chloride known to degrade the optics and mechanic of the cutter
* Any other plastic with "Chlor" or "Fluor" in the name, for the same reasons as PVC and PTFE above.

== '''Test for material''' ==

Some people came up with an easy protocol to help identify unknown polymers: [http://www.nycresistor.com/2008/08/28/how-to-identify-polymers-with-burnination/ Nyc Resistor - how to identify polymers with burnination]. We don't know how reliable it is. And we can't but recommend to do that under good ventilation (outside?)

== Safe Materials ==
The laser can cut or etch. The materials that the laser can cut materials like wood, paper, cork, and some kinds of plastics. Etching can be done on almost anything, wood, cardboard, aluminum, stainless steel, plastic, marble, stone, tile, and glass.
* Cutting
** Many woods up to 1/4" thick. Composite woods like plywood contain glue, and may not laser cut as well as solid wood. Engineered woods like MDF are okay to use but may experience a higher amount of charring when cut. Be very careful about cutting oily woods, or very resinous woods as they also may catch fire.
** Paper cuts very very well on the laser cutter, and also very quickly. Thin paper and single layer card stock and cardboard are perfectly OK. Thicker cardboard, carton, and other papers also cut very well but need to be watched to make sure they don't catch fire.
** Cork cuts nicely, but the quality of the cut depends on the thickness and quality of the cork. Engineered cork has a lot of glue in it, and may not cut as well. Cork thicker than 1/4" should be avoided.
** Cast acrylic (also known as Lucite, Plexiglas, PMMA) cuts extremely well on the laser cutter, leaving a beautifully polished edge. With care, acrylic material up to 1/2" thick can be cut on the laser cutter. Extruded acrylic cuts less well and etches even worse. It tends to melt and puddle rather than vaporize.
** Delrin (POM) in thin sheets cuts and engraves very well. Delrin comes in a number of shore strengths (hardness) and the harder delrin tends to work better. Great for gears! It is possible to deeply engrave Delrin to make dies for embossing paper and leather.
** Kapton tape (Polyimide) : Works well, in thin sheets and strips like tape. 1/16" thick is about as thick as you can cut reliably.
** Mylar : Works well if it's thin. Once you get too far past 1/16" thick mylar has a tendency to warp, bubble, and curl. Gold coated mylar will not work.
** Solid Styrene : Smokes a lot when cut, but can be cut. Keep it thin (1/16")
** Depron foam: Used a lot for hobby, RC aircraft, architectural models, and toys. 1/4" cuts nicely, with a smooth edge. Must be constantly monitored when cutting.
** Cloth (leather, suede, felt, hemp, cotton, polyester, but NEVER vinyl or pleather-- see above) They all cut well. Leather is very hard to cut, but can be if it's thinner than a belt (call it 1/8")
** Magnetic Sheet material cuts beautifully (make SURE it does NOT contain chlorine, see above)
** NON-CHLORINE containing rubber is fine for cutting. Natural rubber engraves but leaves a dark sticky residue that doesn't affect stamps if the piece is engraved deeply enough.
** Carbon fiber mats/weave that has not yet had epoxy applied can be cut, very slowly. You must not cut carbon fiber that has been coated!!
* Etching: all the above can be etched, in some cases very deeply. In addition, you can etch:
** Glass (green seems to work best) .. looks sandblasted. Only FLAT GLASS can be engraved in our cutter. No round or cylindrical items.
** Ceramic tile
** Anodized aluminum ( vaporizes the anodization away )
** Painted/coated metals ( vaporizes the paint away )
** Stone : Marble, Granite, Soapstone, Onyx. Gets a white "textured" look when etched
* Marking
There is an expensive coating called 'cermark'. This marking compound costs $100 for a small bottle, and must be diluted with ethanol and applied to metal (not ceramics or stone) before being etched to leave behind a permanent dark black mark.

=== Material sources ===
* [http://www.inventables.com Inventables] for acrylic
* [http://www.abbeyspecialties.com/ Abbey Specialties] for acrylic in varied sizes, this company is our landlord. They are in the other half of our building and if you ask they can drop off in our shared loading dock.
* [http://www.petersenplastics.com Petersen Brother's Plastics] Has off-cuts and small pieces for $2/lb. 2929 N Pulaski Rd, Chicago, IL 60641 (773) 286-5666
* [http://www.amazon.com/Baltic-Birch-Plywood-Great-Scroll/dp/B00GQND2PK/ref=sr_1_sc_1?ie=UTF8&qid=1421174541&sr=8-1-spell&keywords=laser+plywod Amazon.com] good Baltic Birch 1/8" plywood.
* [http://www.rubberstampmaterials.com/laserengravablerubberandpolymer.aspx Laser-engravable rubber and polymer, for stamps]
* [http://www.amazon.com/Laserable-Rubber-Bundle-Engraving-Machine/dp/B00LIZFXY4/ref=sr_1_fkmr0_1?ie=UTF8&qid=1436036917&sr=8-1-fkmr0&keywords=acrylic+sheet+laserable Amazon, laserable rubber for stamps]

== Strategies and techniques ==

See main article, [[Epilog techniques]].

[[Laser settings]] for various materials.

== General references ==

incredible box maker, with holes and text: http://www.makercase.com/

parametric pdf box creator: http://boxmaker.rahulbotics.com/

parametric svg box creator: http://www.giplt.nl/svg/
(load > construction category > better box)

Ladyada's info on the proper application of laser beams: http://www.ladyada.net/wiki/laserinfo/equipment

Information on materials that can and can't be cut: http://www.pololu.com/docs/0J24/3

paramateric living hinge generator: http://www.ashanan.com/hinges/
(code at: https://github.com/ashanan/hinges)

python svg library written by [[User:toba|Toba]]: https://github.com/eastein/svgcuts

parametric flexbox generator: http://flexbox.herokuapp.com/

http://blog.makezine.com/archive/2008/08/how-to-lasercut-custom-bo.html - Laser cut boxes 

[[:Image:psone-logo-cutout.svg|PS:One Logo]] 

== Long-ass list of laser designs on Thingiverse ==
[http://www.thingiverse.com/tool:33/things All laser cutter things on Thingiverse] 
http://www.thingiverse.com/thing:2321 - Theo Janssen 
http://www.thingiverse.com/thing:2073 - Drill gauge 
http://www.thingiverse.com/thing:247 - Hex connector toy 
http://www.thingiverse.com/thing:1960 - 2010 hex desktop calendar 
http://www.thingiverse.com/thing:2023 - clock 
http://www.thingiverse.com/thing:1739 - shoe hanger 
http://www.thingiverse.com/thing:1616 - geneva wheel 
http://www.thingiverse.com/thing:201 - Square gears 
http://www.thingiverse.com/thing:1521 - Gyroscope 
http://www.thingiverse.com/thing:1393 - End mill set holder 
http://www.thingiverse.com/thing:1203 - 608 bearing wrapper + face 
http://www.thingiverse.com/thing:952 - Small box 
http://www.thingiverse.com/thing:981 - cable chain 
http://www.thingiverse.com/thing:855 - Chess set 
http://www.thingiverse.com/thing:20 - Chess set 
http://www.thingiverse.com/thing:3353 - Chess board with compass rose inlay 
http://www.thingiverse.com/thing:587 - gEarrings 
http://www.thingiverse.com/thing:3411 - gearcuffs 
http://www.thingiverse.com/thing:807 - Mystery box 
http://www.thingiverse.com/thing:516 - tumbler, key, and case 
http://www.thingiverse.com/thing:409 - Resistor lead tool 
http://www.thingiverse.com/thing:211 - Planetary gear business card 
http://www.thingiverse.com/thing:53 - planetary gears 
http://www.thingiverse.com/thing:3021 - Scale mail 
http://www.thingiverse.com/thing:5265 - Peristaltic pump 
http://www.thingiverse.com/thing:5243 - laser cut tetris blocks 
http://www.thingiverse.com/thing:5076 - Wire spool holder 
http://www.thingiverse.com/thing:5727 - Settlers of Catan 
http://www.thingiverse.com/thing:5730 - Teardrop pendant light 
http://www.thingiverse.com/thing:7796 - Gear coasters 

== Software Compatability ==

Note: this indicates success in using this software with the printer driver, not general capabilities about the software itself.

{| border=1
|-
! Software type
! Manufacturer
! File extensions
! Raster (engraving)
! Vector (cutting)
! Other notes
|-
| CorelDraw
| [http://www.corel.com Corel]
| cbr
| yes
| yes
| not available on machine
|-
| Illustrator CC
| [http://www.adobe.com Adobe]
| ai, eps, svg, pdf
| yes
| yes
| available on machine
|-
| Photoshop CC
| [http://www.adobe.com Adobe]
| psd, eps, pdf
| yes
| yes
| available on machine
|-
| Inkscape
| Open Source
|
| yes
| yes (only if printed from PDF)
| save as PDF (vectors should be stroked .01mm), then print from Acrobat. works for bitmap and vector.
|}

== Notes on Software Compatibility ==

Adobe Illustrator and the epilog drivers don't always work great together. If you're experiencing any of the following, there is a simple fix:

# Job runs, but it's an empty run. Laser head moves once then completes, even though raster vs vector is correctly configured and stokes are set to 0.072pt.
# Updating the media size in the epilog print driver does not update the size in Illustrator's print dialog, unless you reopen settings and press 'OK' in epilog again another time or two.
# Open pressing print in Illustrator, you get a message about "nothing to print in selected layers" or similar.
# Media size entered in epilog driver is read as the reverse by Illustrator (e.g. 24x12 is seen as 12x24 by Illustrator)

It seems epilog's driver doesn't play nicely with Illustrator, and Illustrator interfaces with the print driver a lot because it micromanages a lot of things.
If your document is saved as a .AI with PDF compatibility, simply right-click your AI file and open with Adobe Reader instead of Adobe Illustrator, and print from there.

Adobe Reader has a much more "dumbed down" print dialog that just works with Epilog's driver. You don't have to resave your .AI as .PDF, as Adobe Reader can read .AI files saved in compatibility mode (that's the default).

== Rotary Attachment ==

'''NB: Always return the machine back to the default configuration with a cutting bed after use.'''

=== Installing Attachment ===

'''Do not attempt to install the rotary attachment without ensuring that the cutting head AND autofocus plunger will clear it. It is extremely easy to damage the autofocus plunger and/or crash the head in the Y dimension, which will burn the motor out and make a lot of people sad.'''

# Turn machine on
# Disable X/Y
# Open front cover
# Lower bed almost to the bottom of the machine while still allowing the catch tray to be removed
# '''Turn machine off'''
# Flip up rulers and remove cutting bed
# Remove slide out catch tray
# Install the attachment locating it in the 3 holes in the bottom of the bed '''DO NOT CONNECT PLUG YET'''
# Make sure the Y axis will clear the top of the attachment, if it will not turn the machine on and lower the bed further making sure to turn it off afterwards
# Connect the attachment cable to the connector in the back of the bed
# Turn the machine on - the machine will zero home over the top of the attachment

Reverse steps to uninstall.

=== Usage notes ===

* '''DO NOT USE AUTO FOCUS'''
* 0,0 is '''TOP LEFT'''
* Y axis is wrapped around the piece
* Set Y size to circumference of piece - measure with soft tape or string/ribbon/etc
* Make sure to set print size in driver to same as art board in illustrator

== Known issues ==

=== Can't login ===

==== The trust relationship between this workstation and the primary domain failed ====

* main page [[The trust relationship between this workstation and the primary domain failed]]
** Might be fixed now
** Occasional workaround: reboot

==== I was certified a long time ago ====

You need to
# Be a Current Member
# Have a https://members.pumpingstationone.org account
# Talk to a recommended certifier, The area host, or email info@pumpingstationone.org

You may be asked to get recertified.

==== Front door interlock broken ====

The front door interlock has two reed switches. The one on the right isn't being activated by the factory magnet so it currently has an additional magnet on the inside of the machine, right to the left of the switch

== List of Currently Certified Users ==

This list is hugely incomplete because nobody was doing it. Someone should fix that eventually... for now, new certs should go in here. If you are certified and remember who certified you, go ahead and add yourself. Your non-presence on this list is not intended to insult you or your relatives.

{| class="wikitable" border="1"
! Qualified Member
! Trained By
|-
|Nat Zorach
|Will McShane
|-
|[[User:anthony|Anthony Sontag]]
|Elizabeth
|-
|Will McShane
|Danger Committee
|-
|Eric Stein
|Will McShane
|-
|Patrick Schless
|Will McShane
|-
|Laurie Rich
|Steve
|-
|Tom Forajter
|Will McShane
|-
|Colin Parsons
|Patrick Swayze (RIP)
|-
|Andrew Camardella
|Colin Parsons
|-
|Dan Locks
|Colin Parsons
|-
|Mahmoud Al-Qudsi
|Colin Parsons
|-
|Lauren Conroy
|Colin Parsons
|-
|Jesse Seay
|Colin Parsons
|-
|Sai Yamanoor
|Colin Parsons
|-
|Hef
|Colin Parsons
|-
|Adam Talsma
|Colin Parsons
|-
|Josh Cooper
|Colin Parsons
|-
|Bryan Rosendale
|Colin Parsons
|-
|Kevin Caughlin
|Colin Parsons
|-
|Nathan Becka
|Colin Parsons
|-
|Stephen Kamykowski
|Colin Parsons
|-
|Jesse Seay
|Colin Parsons
|-
|Bart Dring
|Colin Parsons
|-
|Mike Morarity
|Colin Parsons
|-
|Tony Dipaolo
|Colin Parsons
|-
|Adrew An
|Colin Parsons
|-
|Dean Anderson
|Colin Parsons
|-
|Francesca Slade
|Colin Parsons
|-
|David Fell
|Colin Parsons
|-
|Ron Olson
|Colin Parsons
|-
|[[User:Jaypee|Jay Pee]]
|Elizabeth
|-
|Peter Borah
|Elizabeth
|-
|April
|Elizabeth
|-
|[[User:rdoeksen|Ray Doeksen]]
|Elizabeth
|-
|Jason Shanfield
|Will McShane
|-
|Elizabeth Koprucki
|Will McShane
|-
|George Shaw
|Will McShane
|-
|Andrew Kos
|Elizabeth Koprucki
|-
|Derek Bever
|Elizabeth Koprucki
|-
|Jason Araujo
|Derek Bever
|-
|Adam Glick
|Ray Doeksen
|-
|Nathan Ellis
|Jason Shanfield
|-
|[[user:rob|Rob Riggs (Colorado Rob)]]
|Elizabeth
|-
|[[User:ad9581|Arturo Duarte]]
|Elizabeth Koprucki
|-
|[[User:jivnyahoo|James Porter]]
|Elizabeth Koprucki
|-
|[[User:ryankelly11|Ryan Kelly]]
|Elizabeth Koprucki
|-
|[[User:sloanieb01|Sloan Lavery]]
|William McShane
|-
|Casey Olson
|Jason Shanfield
|-
|Spenser Gilliland
|Elizabeth Koprucki
|-
|Jeff McBride
|Elizabeth Koprucki
|-
|David Morton
|Elizabeth Koprucki
|-
|Thomas Wright
|Elizabeth Koprucki
|-
|Touly Phiachantharath
|Elizabeth Koprucki
|-
|Robert Grossman
|Elizabeth Koprucki
|-
|Eddie Muela
|Elizabeth Koprucki
|-
|Rachel Wallis
|Elizabeth Koprucki
|-
|Nick Halderman
|Elizabeth Koprucki
|-
|Eric Beauchamp
|Jason Shanfield
|-
|Aaron Mintz
|Elizabeth Koprucki
|-
|Matt Makris
|Elizabeth Koprucki
|-
|[[User:RogerMoore|Roger Moore]]
|Elizabeth Koprucki
|-
|Michael Leinartas
|Elizabeth Koprucki
|-
|Solomon Hursey
|Elizabeth Kopruki
|-
|[[User:daroldhiga|Darold Higa]]
|Elizabeth Koprucki
|-
|Curtiss Cooke
|Elizabeth Koprucki
|-
|Dubi Kaufmann
|Elizabeth Koprucki
|-
|Maria Miller
|Derek Bever
|-
|Andrew Sowa
|Elizabeth Koprucki
|-
|Mike Kislovsky
|Will McShane
|-
|Kyle Bieneman
|Will McShane
|-
|Michael Solheim
|Elizabeth Koprucki
|-
|Tim Geiser
|Elizabeth Koprucki
|-
|[[User:lucas|Lucas Goossen]]
|Elizabeth Koprucki
|-
|Alec Weege
|Jason Shanfield
|-
|Arjun Wadnerkar
|Jason Shanfield
|-
|Kevin Pulver
|Ray Doeksen
|-
|David Butler
|Ray Doeksen
|-
|Mike Mandrea
|Elizabeth Koprucki
|-
|Davis Mazariegos
|Elizabeth Koprucki
|-
|John Farmer
|Elizabeth Koprucki
|-
|Knute Martell
|Elizabeth Koprucki
|-
|[[User:leonmf|Leon Grossman]]
|Jason Shanfield
|-
|[[User:Tina|Tina C]]
|Elizabeth Koprucki
|-
|Benjamin Miller
|Jason Shanfield
|-
|Ryan Taylor
|Jason Shanfield
|-
|Joe Wallace
|Jason Shanfield
|-
|Ryan Neuman
|Elizabeth Koprucki
|-
|Scott Little
|Ray Doeksen
|-
|Scott Drane
|Ray Doeksen
|-
|Will Garza
|Ray Doeksen
|-
|Mike Jones
|Ray Doeksen
|-
|Bryan Sills
|Ray Doeksen
|-
|Mike Patton
|Ray Doeksen
|-
|James Huber
|Jason Shanfield
|-
|[[user:kuroishi|Doorman Dave]]
|Elizabeth Koprucki
|-
|Simon Pyle
|Jason Shanfield
|-
|Kurt Ziegel
|Lyn Cole
|-
|Ralph Brendler
|[[user:Bjonnh|Jonathan Bisson]]
|-
|Robert Caruso
|Ray Doeksen
|-
|(Raj) Joseph Perera
|Ray Doeksen
|-
|[[user:Bjonnh|Jonathan Bisson]]
|Elizabeth Koprucki
|-
|[[User:Wessing|Erik Wessing]]
|Ray Doeksen
|-
|[[User:crumpn8or|Matt Crump]]
|Ray Doeksen
|-
|[[User:motissia|Eugene Liolumovich]]
|Ray Doeksen
|-
|[[User:avner|Avner Shanan]]
|Ray Doeksen
|-
|Chinzorig Davaatseren
|Ray Doeksen
|-
|Temuulen Erdenekhvv
|Ray Doeksen
|-
|Krista Benson
|Ray Doeksen --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 16:09, 28 August 2015 (CDT)
|-
|Bradley Jiminez
|Ray Doeksen --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 16:09, 28 August 2015 (CDT)
|-
|James Baker
|Ray Doeksen
|-
|Hunter Koerner
|Ray Doeksen
|-
|Tricia Scully
|Ray Doeksen
|-
|Danika Faiola --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 21:34, 9 September 2015 (CDT)
|Ray Doeksen
|-
|Jim Hartmann
|Ray Doeksen
|-
|Jonathan Levine
|Ray Doeksen
|-
|Keith Hultman
|Khoi Nguyen
|-
|Julia Padvoiskis
|Ray Doeksen
|-
|Erik Funkhouser
|Ray Doeksen
|-
|Steve Kuenstler
|Elizabeth Koprucki
|-
|Shane Kanter 10/18/2015
|Ray Doeksen
|-
|Andy Larkin 10/20/2015
|Ray Doeksen
|-
|David Gutowsky
|Ray Doeksen
|-
|Nicholas Hawley
|Ray Doeksen
|-
|Kevin Mitchell
|Ray Doeksen
|-
|David Rubman 11/23/2105
|Ray Doeksen
|-
|Jeff Smykil
|Ray Doeksen
|-
|Samuel Sion
|Ron Olson
|-
|David O'Brien --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 22:37, 21 December 2015 (CST)
|Ray Doeksen
|-
|Greg Kudlacz
|Ray Doeksen
|-
|Daya Alexander
|Ray Doeksen
|-
|Andrew Dalesandro
|Ray Doeksen
|-}

== Authorizing Users ==

The laser cutter now has [[:Category:Recommended laser authorizers|recommended authorizers]]. Recommended authorizers will periodically conduct authorization sessions for PS:1 members wishing to use the laser engraver. These sessions will be announced on the members' listserv as early as is practicable. A recommended authorizer can follow the instructions on [[Laser Engraver Certification]] to enable logins to the laser engraver computer.

[[Category:Laser Cutter]]
[[Category:Electronics Equipment]]
[[Category:Fabrication]]
[[Category:Certification Clarification Needed]]

Lulzbot Taz3

2016-01-15T21:15:47Z

Andrewd: /* List of Currently Certified Users */

{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = no
|model = Aleph Objects Taz3
|serial = KT-PR0013-5509
|arrived = January 2014
|doesitwork = no
|contact = [[CNC|CNC Area Host]]
|where = [[CNC]] 2nd Floor
|value = $2395
|image = Taz3.jpg
|hostarea = CNC
}}

== Status ==
As of 12/20/2015 Someone has put a note saying "no work" on the print bed, no further information known.

As of 12/10/2015 Undergoing testing. Functional. New LCD installed, SD card reader should be working but has not been tested in use. Fiberglass flexible print bed add-on installed. Firmware updated for new Hexagon extruder heads, no longer compatible with Flexistruder, for now. Hexagon heads need to be set higher than old heads (temperatures will need to be higher.) Additional testing required to advise what temperatures are best. --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 16:17, 10 December 2015 (CST)

As of 11/13/2015 the main PLA/ABS extruder is not working, replacement extruders and parts are ordered or awaiting installation by CNC Area Host.

As of 9/28/2015 not clogged, working normally, DO NOT RUN PLA for longer than 1hr --[[User:Rtystgeeke|Rtystgeeke]] ([[User talk:Rtystgeeke|talk]]) 15:26, 28 September 2015 (CDT)

As of 7/20/2015 nozzle clogged with PLA, resistor wire is broken (needs replacement), bottom wood disk is broken (needs replacement) --Andrew Camardella 7/20/2015 5:35pm

As of 6/3/2015 nozzle unclogged, tested with ABS. --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 19:22, 3 June 2015 (CDT)

As of 6/1/2015 clogged with PLA through the length of the hot end and nozzle. Needs to be disassembled, burned out, nozzle cleaned. Probably needs replacement nozzle. Needs replacement parts for the hot end (wood discs, maybe aluminum disk) --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 18:53, 1 June 2015 (CDT)

As of 5/20/2015 not clogged, running normally.

Seems to be extruding fine as of 4/30/2015. [Extruder nozzle clogged. Needs unclogging or nozzle replacement. (As of 4/28/2015, clogged )]

== Authorization ==

Under construction. Ask CNC Area Host. No regularly scheduled authorizations. Authorization sessions can be arranged for 3 or more members as required. If you want to schedule an authorization session, find 2 or more other people and email the CNC Area Host for referral to an authorizer.

== Operation ==
* Turn the printer off when you are no longer using it.

== Troubleshooting ==

Under construction. Please add information to this section if you discover some useful tips and tricks.

*Usually is COM5
*If you can't connect on COM5, you may need to reboot the PC, because another user is still logged in after they connected on COM5.
*Make sure baud rate is set to 115200
*Make sure protocol is set to Autodetect
*In Repetier Host, home the machine to get full motion on the axes

== Mods ==
Factory standard settings, accessories and equipment. Alternate Flexistruder available at PS1 but not installed.

=== Windows Drivers ===
Windows users driving the printer tethered (over a USB cable) will need to [https://www.lulzbot.com/support/TAZ install drivers.]

=== Usable Print Area ===
298mm x 275mm x 250mm (11.7in x 10.8in x 9.8in)

=== Nozzle size ===
* 0.50 mm nozzle --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 16:20, 10 December 2015 (CST)(please verify?)

=== Host Software ===
Users of Linux, Windows, OSX will need to install the following software:
* [https://github.com/kliment/Printrun#getting-printrun Pronterface] - or [http://www.repetier.com/download/ Repeteir-Host] for manual operation of the printer as well as for starting print jobs
* [http://slic3r.org/download Slic3r] - for creating gcode (print jobs) from 3D models
* Additionally, Lulzbot provides a [http://devel.lulzbot.com/TAZ/2.1/software/2013Q4/slic3r/config/pt35mm-nozzle/medium_ABS_no-support_pt35nzl_pt2-layer-height_config.ini slic3r config file] for the Taz3
* Alternately, you can use [http://wiki.ultimaker.com/Cura Cura by Ultimaker]

== Suggested Settings ==

Both of these files have appropriate settings for the 'printer settings' and 'filament settings' tabs. To use them, go to File > Load Config in Slic3r and select the downloaded file. You must then go to each tab and hit the 'save' icon next to the settings selection dropdown box, or else Slic3r will forget the settings when you close it.

==== ABS Print Settings Without Support - Fast ====

[[File: Taz3_print_settings_NO_SUPPORT.ini]]

This file is for the 'print settings' tab of Slic3r. This is a 'fast' profile, geared towards finishing prints relatively quickly. It still provides excellent surface quality. This profile does not include support, so for large overhangs you'll need the next configuration file.

==== ABS Print Settings With Support - Fast ====

[[File: Taz3_print_settings_SUPPORT.ini]]

This file is for 'print settings' tab of Slic3r. This is a 'fast' profile, geared towards finishing prints relatively quickly. It still provides excellent surface quality. This profile includes support, appropriate for large overhangs.

== Other Resources ==
[http://download.lulzbot.com/TAZ/3.0/documentation/2013Q4/LulzBot_TAZ_3.0-User_Manual-ebook.pdf The manual is available online]. A printed form of it can be found near the printer. The manual explains how to operate the printer.

=== Filament ===

The extruders available accept 3 mm filament, and can print either ABS or PLA. There is an alternate extruder for use with Ninjaflex, called 'Flexistruder' but the Flexistruder is not supported with the current firmware installation.

[https://www.inventables.com/categories/materials/3d-printer-filament Inventables]

[http://www.monoprice.com/Search/Index?keyword=3d+printer+filament Monoprice]

=== Find Something to Print ===

[http://thingiverse.com Thingiverse] is a great place to find printable 3D models that other people have designed, and to publish your own.

=== Designing 3D Models ===

Page in progress to describe [https://wiki.pumpingstationone.org/3D_Modeling 3D modeling.]

== List of Currently Certified Users ==
{| class="wikitable" border="1"
! qualified member
! trained by
|-
|[[User:Dbever|Derek Bever]]
|Hours of shouting at 3D printers
|-
|Elizabeth Koprucki
|Derek Bever
|-
|Andrew Kos
|Elizabeth Koprucki
|-
|[[User:rdoeksen|Ray Doeksen]]
|Elizabeth Koprucki
|-
|[[User:Negativek|Everett Wilson]]
|Derek Bever
|-
|[[User:daveplays|David Earley]]
|Derek Bever
|-
|[[User:Lyn|Lyn Cole]]
|Derek Bever
|-
|[[User:nerobro|Greg Teiber]]
|Derek Bever
|-
|[[User:nick|Nick Castillo]]
|Derek Bever
|-
|[[User:tom4writer|Tom Forajter]]
|Elizabeth Koprucki
|-
|[[User:dditzler|David Ditzler]]
|Elizabeth Koprucki
|-
|[[User:davidfell|David Fell]]
|Elizabeth Koprucki
|-
|[[user:rob|Rob Riggs (Colorado Rob)]]
|Elizabeth
|-
|Mark Stevens
|Elizabeth Koprucki
|-
|[[User:ad9581|Arturo Duarte]]
|Elizabeth Koprucki
|-
|[[User:justin|Justin T. Conroy]]
|Derek Bever
|-
|[[User:jivnyahoo|James Porter]]
|Elizabeth Koprucki
|-
|[[User:ryankelly11|Ryan Kelly]]
|Elizabeth Koprucki
|-
|[[User:JanetD|Janet Dornhoff]]
|Elizabeth Koprucki
|-
|Genevieve Aphrodite
|Justin Conroy
|-
|Sloan Lavery
|Elizabeth Koprucki
|-
|[[User:spacekid|Adam Glick]]
|Ray Doeksen
|-
|[[User:funk|Tyler Natoli]]
|Elizabeth Koprucki
|-
|Chris Marchwick
|Elizabeth Koprucki
|-
|[[User:marty|Marty Dubin]]
|Elizabeth Koprucki
|-
|[[User:amishhammer|Tom Judge]]
|Justin Conroy
|-}
|-
|[[User:brian|Brian Dunn]]
|Derek Bever
|-|-
|[[User:lofgren|Tim Lofgren]]
|Derek Bever
|-
|[[User:lgaboarder|Jeff McBride]]
|Elizabeth Koprucki
|-
|Thomas Wright
|Justin Conroy
|-
|[[User:dsiegfried|David Siegfried]]
|Derek Bever
|-
|Donald Jacobson
|Elizabeth Koprucki
|-
|[[User:Sparr|Clarence Risher]]
|Elizabeth Koprucki
|-
|[[User:ironwill|Will Garza]]
|Elizabeth Koprucki
|-
|[[User:emertonom|Nick Halderman]]
|Elizabeth Koprucki
|-
|[[User:tactics|Michael Maloney]]
|Elizabeth Koprucki
|-
|[[User:tactics|Brennan Koziarz]]
|Elizabeth Koprucki
|-
|[[User:rogermoore|Roger Moore]]
|Elizabeth Koprucki
|-
|[[User:aaronmintz|Aaron Mintz]]
|Elizabeth Koprucki
|-
|[[User:mlm|Matt Makris]]
|Elizabeth Koprucki
|-
|Matt Meshulam
|Elizabeth Koprucki
|-
|Ron Olson
|Elizabeth Koprucki
|-
|[[User:daroldhiga|Darold Higa]]
|Ray Doeksen
|-
|Nora Sluzas
|Elizabeth Koprucki
|-
|Matt Triano
|Elizabeth Koprucki
|-
|Curtiss Cooke
|Elizabeth Koprucki
|-
|Andrew Sowa
|Elizabeth Koprucki
|-
|Eric Yu
|Elizabeth Koprucki
|-
|[[User:lucas|Lucas Goossen]]
|Elizabeth Koprucki
|-
|Jessica Wiedner
|Derek Bever
|-
|Scott Little
|Derek Bever
|-
|Kevin Pulver
|Ray Doeksen
|-
|Jenny Tong
|Ray Doeksen
|-
|Mike Mandrea
|Elizabeth Koprucki
|-
|John Farmer
|Elizabeth Koprucki
|-
|Andy Richardson
|Elizabeth Koprucki
|-
|Alex Trimm
|Elizabeth Koprucki
|-
|[[User:rickalm|Rick Alm]]
|Elizabeth Koprucki
|-
|Davis Mazariegos
|Elizabeth Koprucki
|-
|Knute Martell
|Elizabeth Koprucki
|-
|Hugh Sato
|Elizabeth Koprucki
|-
|Ryan Neuman
|Will Garza
|-
|[[User:Tina|Tina C]]
|Elizabeth Koprucki
|-
|Scott Drane
|Elizabeth Koprucki
|-
|Michael Patton
|[[User:rdoeksen|Ray Doeksen]]
|-
|Chris Leeson
|[[User:rdoeksen|Ray Doeksen]]
|-
|Matt Pollina
|[[User:rdoeksen|Ray Doeksen]]
|-
|Scott Anamizu
|[[User:rdoeksen|Ray Doeksen]]
|-
|[[user:kuroishi|Doorman Dave]]
|Elizabeth Koprucki
|-
|Simon Pyle
|[[User:rdoeksen|Ray Doeksen]]
|-
|Brad Jiminez
|[[User:rdoeksen|Ray Doeksen]]
|-
|Nate Scheidler
|[[User:rdoeksen|Ray Doeksen]]
|-
|Alan Insley
|[[User:rdoeksen|Ray Doeksen]]
|-
|Wessing
|[[User:rdoeksen|Ray Doeksen]]
|-
|[[User:w9lp|Casey Coley]]
|Andrew Camardella
|-
|Deanna Williams
|Brad Jimenez
|-
|Jim Hartmann
|Ray Doeksen --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 14:44, 20 September 2015 (CDT)
|-
|Hunter Koerner
|Ray Doeksen
|-
|Temnulen Erdenekhun
|Ray Doeksen
|-
|Greg Teiber
|Ray Doeksen
|-
|Bob Williams
|Ray Doeksen
|-
|Elizabeth Arundel
|Brad Jimenez
|-
|Alex Al-Hamdan
|Brad Jimenez
|-
|Nem Simeunovic
|Brad Jimenez
|-
|Dafe Hughes
|Brad Jimenez
|-
|Gary Silver
|Brad Jimenez
|-
|Daniel Maziarz
|Brad Jimenez
|-
|Greg Kudlacz
|Brad Jimenez
|-
|Adam Moffatt
|Brad Jimenez
|-
|Kevin Schwartzenberg
|Andrew Camardella
|-
|Michael Slingerland
|Andrew Camardella
|-
|Andrew Dalesandro
|Andrew Camardella
|-
[[Category:Fabrication]]
[[Category:CNC]]

LulzBot AO-100 3D Printer

2016-01-15T21:15:31Z

Andrewd: /* List of Currently Certified Users */

{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = no
|model = Aleph Objects AO-100
|serial =
|arrived = January 2013
|doesitwork = no
|contact = [[CNC|CNC Area Host]]
|where = [[CNC]] 2nd Floor
|value = $1725
|itemphoto=
| image = Lulzbot.jpg
|hostarea = CNC
}}

== Status ==
As of 11/13/2015 Not working. RD

Working Beautifully! I had to completely dismantle the extruder. Someone had jammed a ton of orange PLA in there. I even had to drill it out of the plastic part just above the hot end. There was melted material oozing out all kinds of places that it shouldn't be. The actual hot end was packed full of this carbon type stuff (maybe over heated PLA?). I replaced the .5 extrusion tip with the .35 tip. I believe the .5 is permanently damaged due to abusive scraping of the tip. (Scraping the tip will not unclog the head) LG 5/14/2015

Hasn't been used much. Spool-holding bolt is inadequate to hold a spool. Doesn't appear to be extruding ABS even at 230 C. Investigating. RD 5/8/2015

== Operation ==
Don't forget to turn the printer off when you are no longer using it. Also, wipe your own nose.

=== Windows Drivers ===
Windows users will need to install drivers.
For everyone else, It Just Works™. Where everyone = Linux and OSX users.

=== Usable Print Area ===
200mm (X-axis) x 190mm (Y-axis) x 100mm (Z-axis)
(7.9in x 7.5in x 3.9in)

=== Host Software ===
Users of Linux, Windows, OSX will need to install the following software:
* [https://github.com/kliment/Printrun#getting-printrun Pronterface] - or [http://www.repetier.com/download/ Repeteir-Host] for manual operation of the printer as well as for starting print jobs
* [http://slic3r.org/download Slic3r] - for creating gcode (print jobs) from 3D models
* Additionally, Lulzbot provides a [http://download.lulzbot.com/AO-100/software/2012-Q2/configs/slic3r/point5mm.ini config file] for the AO-100 LulzBot. (Note: remember to change nozzle to .5 after importing the config file.)

=== Suggested Settings ===
Nozzle diameter = 0.35 mm

Filament diameter = 3.0 mm

COM port - 4 (usually)

Data rate = 115200

Temperature (degrees C)
Extruder: 230
Bed: 110

Lulzbot's slic3r config has the infill density set at 0.75. Resulting prints are very sturdy as a result, but the filament consumption and print time go up because of this. It is recommended to turn it down to 0.15 or 0.25, and to increase the number of infill shells. Doing so should have a similar surface quality, but produce a print with significantly less mass.

=== Other Resources ===
[http://download.lulzbot.com/AO-100/documentation/2012Q3/AO-100-User_Manual.pdf The manual is available online]. A printed form of it can be found near the printer. The manual explains how to operate the printer. Read it =)

=== Filament ===
The printer is currently configured for 3mm ABS plastic. Only use this kind of plastic. Until Aeva has a chance to upgrade the extruder, PLA can damage the hot end.

=== Find Something to Print ===

[http://thingiverse.com Thingiverse] is a great place to find printable 3D models that other people have designed, and to publish your own.

=== Designing 3D Models ===

Page in progress to describe [https://wiki.pumpingstationone.org/3D_Modeling 3D modeling.]

== List of Currently Certified Users ==

{| class="wikitable sortable" border="1"
! qualified member
! trained by
|-
|Lyn Cole
|Colin Parsons
|-
|Arkadiusz Czubak
|Colin Parsons
|-
|Michael Skilton
|Steve Finkelman
|-
|Eric Maxon
|Steve Finkelman
|-
|David Fell
|Elizabeth Koprucki
|-
|Ray Doeksen
|Steve Finkelman
|-
|Derek Bever
|Elizabeth Koprucki
|-
|Ricardo Cagnetta
|Derek Bever
|-
|Jeffrey Camealy
|Derek Bever
|-
|Solomon Hursey
|Derek Bever
|-
|Nick Castillo
|Derek Bever
|-
|Ralph Weidenbach
|Derek Bever
|-
|David Earley
|Steve Finkelman
|-
|Tom Forajter
|Elizabeth Koprucki
|-
|[[user:rob|Rob Riggs (Colorado Rob)]]
|Elizabeth
|-
|Adam Glick
|Ray Doeksen
|-
|[[User:ad9581|Arturo Duarte]]
|Elizabeth Koprucki
|-
|[[User:jivnyahoo|James Porter]]
|Elizabeth Koprucki
|-
|[[User:ryankelly11|Ryan Kelly]]
|Elizabeth Koprucki
|-
|[[User:knitmeapony|Laurie Rich]]
|Elizabeth Koprucki
|-
|Mark Stevens
|Elizabeth Koprucki
|-
|[[User:Jay|Jay Strybis]]
|Elizabeth Koprucki
|-
|[[User:JanetD|Janet Dornhoff]]
|Elizabeth Koprucki
|-
|Sloan Lavery
|Elizabeth Koprucki
|-
|[[User:funk|Tyler Natoli]]
|Elizabeth Koprucki
|-
|[[User:amishhammer|Tom Judge]]
|Justin Conroy
|-
|[[User:hypertaxia|Dan Thomson]]
|Elizabeth Koprucki
|-
|[[User:lgaborder|Jeff McBride]]
|Elizabeth Koprucki
|-
|[[User:Sparr|Clarence Risher]]
|Elizabeth Koprucki
|-
|[[User:emertonom|Nick Halderman]]
|Elizabeth Koprucki
|-
|[[User:Sparr|Brennan Koziarz]]
|Elizabeth Koprucki
|-
|[[User:aaronmintz|Aaron Mintz]]
|Elizabeth Koprucki
|-
|[[User:mlm|Matt Makris]]
|Elizabeth Koprucki
|-
|[[User:cvrtw|Alex Schaffer]]
|Elizabeth Koprucki
|-
|[[User:AutoRunFail|Michelle Scott]]
|Elizabeth Koprucki
|-
|Matt Meshulam
|Elizabeth Koprucki
|-
|[[User:RogerMoore|Roger Moore]]
|Elizabeth Koprucki
|-
|[[User:daroldhiga|Darold Higa]]
|Ray Doeksen
|-
|Nora Sluzas
|Elizabeth Koprucki
|-
|Matt Triano
|Elizabeth Koprucki
|-
|Curtiss Cooke
|Elizabeth Koprucki
|-
|Andrew Sowa
|Elizabeth Koprucki
|-
|Mike Kislovsky
|Elizabeth Koprucki
|-
|Mark Cabael
|Elizabeth Koprucki
|-
|[[User:lucas|Lucas Goossen]]
|Elizabeth Koprucki
|-
|Jessica Wiedner
|Derek Bever
|-
|Scott Little
|Derek Bever
|-
|Alex Maties
|Elizabeth Koprucki
|-
|Bruce Sanders
|Elizabeth Koprucki
|-
|Jenny Tong
|Justin Conroy & Ray Doeksen
|-
|Mike Mandrea
|Elizabeth Koprucki
|-
|Andy Richardson
|Elizabeth Koprucki
|-
|Eric Yu
|Elizabeth Koprucki
|-
|[[User:rickalm|Rick Alm]]
|Elizabeth Koprucki
|-
|Davis Mazariegos
|Elizabeth Koprucki
|-
|Knute Martell
|Elizabeth Koprucki
|-
|[[User:Tina|Tina C]]
|Elizabeth Koprucki
|-
|Ryan Neuman
|Will Garza
|-
|[[user:kuroishi|Doorman Dave]]
|Elizabeth Koprucki
|-
|[[user:stevenelson|Steve Nelson]]
|Elizabeth Koprucki
|-
|Nem Simeunovic
|Brad Jimenez
|-
|Dafe Hughes
|Brad Jimenez
|-
|Gary Silver
|Brad Jimenez
|-
|Daniel Maziarz
|Brad Jimenez
|-
|Greg Kudlacz
|Brad Jimenez
|-
|Adam Moffatt
|Brad Jimenez
|-
[[Category:Fabrication]]

LulzBot AO-100 3D Printer

2016-01-15T21:14:25Z

Andrewd: /* List of Currently Certified Users */

LulzBot AO-100 3D Printer

2016-01-15T21:13:46Z

Andrewd: /* List of Currently Certified Users */

Ryobi 6" grinder

2016-01-15T21:11:50Z

Andrewd: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = no
|model = MODEL NUMBER
|serial = SERIAL NUMBER
|arrived = DATE
|doesitwork = yes
|contact = CONTACT PERSON
|where = hot metals area
|value = DOLLARS
|image = Ryobi grinder.jpg
}}

'''This tool requires certification for use.'''
== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
|-
|[[user:kuroishi|David Koppel]]
|Adrianna McKinley
|-
|Michael Leinartas
|Adrianna McKinley
|-
|Kyle Bieneman
|Todd Allen
|-
|Scott Little
|Todd Allen
|-
|RJ Metzger
|Todd Allen
|-
|Giovanni Arroyo
|Todd Allen
|-
|Joao Santos
|Todd Allen
|-
|Nicholas Haldereman
|Todd Allen
|-
|Doorman Dave
|Todd Allen
|-
|Stephen Ioannou
|Todd Allen
|-
|Lucas Goossen
|Todd Allen
|-
|[[user:RogerMoore|Roger Moore]]
|Todd Allen
|-
|[[User:Mwilkens|Matt Wilkens]]
|Todd Allen
|-
|Rhonda Jackson
|Todd Allen
|-
|Matt Meshulam
|Todd Allen
|-
|Kevin Pulver
|Todd Allen
|-
|Andrew Camardella
|Todd Allen
|-
|Mike Coriale
|Todd Allen
|-
|Nick Naro
|Todd Allen
|-
|John Farmer
|Todd Allen
|-
|[[user:Jaypee|Jay Pee]]
|Todd Allen
|-
|Sam Paris
|Todd Allen
|-
|Jake Rush
|Todd Allen
|-
|Carolyn Ignacio
|Todd Allen
|-
|Andrew Sowa
|Todd Allen
|-
|Hilary Lee
|Todd Allen
|-
|Eric Slehofer
|Todd Allen
|-
|Sam Reicks
|Todd Allen
|-
|Tyler Matthew
|Todd Allen
|-
|Ben Bogler
|Todd Allen
|-
|Brittany Krawczyk
|Todd Allen
|-
|Cary Lahucik
|Todd Allen
|-
|Dan Baltudis
|Todd Allen
|-
|Shae Kurko
|Todd Allen
|-
|Glenn Powers
|Ron Olson
|-
|Ryan Neuman
|Ron Olson
|-
|Jim Baker
|Ron Olson
|-
|Jeff Lawson
|Ron Olson
|-
|James Villalpando
|Ron Olson
|-
|Peter Letscher
|Todd Allen
|10/28/15
|-
|Jean Michel Crettaz
|Todd Allen
|-
|Andrew Dalesandro
|Michael Patton
|1/10/16
|-
|-}

[[Category:Metalworking]]
[[Category:Shop Equipment]]

DeWalt Chop Saw

2016-01-15T21:10:18Z

Andrewd: /* Authorized Users */

{{Template:EquipmentPage
|owner=PS1
|model=14" Chop Saw
|serial=?
|arrived=5/10/2015
|doesitwork=yes
|contact=Ron Olson
|where=Hot Metals Area
|certification=yes
|hackable=no
|value=$200
|image=IMG_2204.JPG
}} 
== Authorization ==
Authorization is done via the Tier 1 class
== Authorized Users ==

{| class="wikitable" border="1"
! Qualified Member
! Trained By
!Date Trained
|-
|Hunter Koerner
|Ron Olson
|6/14/15
|-
|Raj Perera
|Ron Olson
|6/14/15
|-
|-
|Erik Wessing
|Ron Olson
|
|-
|Aji Slater
|Ron Olson
|7/12/15
|-
|Jim Baker
|Ron Olson
|-
|Todd Allen
|Ron Olson
|-
|Tom Boeman
|Ron Olson?
|8/30/15
|-
|Jonathan Levine
|Todd Allen
|9/23/15
|-
|Niko Hawley
|Ron Olson
|-
|Glenn Powers
|Ron Olson
|10/18/15
|-
|Aaron Carlock
|Ron Olson
|11/18/15
|-
|Jennie P
|Ron Olson
|11/18/15
|-
|Kurt Ziegel
|Ron Olson
|11/18/15
|-
|Mike Forkan
|Ron Olson
|11/18/15
|-
|Marcin Ignasiak
|Ron Olson
|-
|Greg Kudlacz
|Ron Olson
|-
|Elizabeth Arundel
|Ron Olson
|10/18/15
|-
|Daniel Maziarz
|Ron Olson
|-
|Jean Michel Crettaz
|Ron Olson
|-
|Dafe Hughes
|Ron Olson
|12/16/15
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/15
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/15
|-
|Andrew Dalesandro
|Michael Patton
|1/10/16
|-
|Peter Brask
|Eric Beauchamp
|1/14/16

[[Category:Shop Equipment]]
[[Category:Fabrication]]
[[Category:Metalworking]]
[[Category:Coldmetals]]

DoAll Drill Press

2016-01-15T21:09:33Z

Andrewd: /* List of Currently Authorized Users */

{{Template:EquipmentPage
| owner = Dillon Gray
| model = 58-51
| serial = 58-333
| arrived = 2012
| doesitwork = yes
| contact = Dean Anderson
| where = Machine Shop
| certification = yes
| hackable = no
| value = $800
| image = DoallDro.jpg
}}
This Doall model appears to be a rebadged Wilton 5816.

== Problems ==
During an auth, Everett noticed significant wobble in the chuck -- enough to make it unusable. Ron Bean fixed by replacing the chuck on 5/15/15.

=== Upgrades ===
[[User:Dbever | Derek]] added a tachometer/DRO. [https://github.com/loansindi/Do-All-DRO Patches welcome].

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
|-
|Dillon Gray
|Dillon Gray
|-
|Eric Stein
|Steven Finkelman
|-
|Ryan Pierce
|Mike Warot
|-
|Larry Thorpe
|Mike Warot
|-
|Tucker Tomlinson
|Steve Finkelman
|-
|Charlie Stauffer
|Tucker Tomlinson
|-
|Michael Skilton
|Tucker Tomlinson
|-
|Dee Newcum
|Tucker Tomlinson
|-
|David Fell
|Tucker Tomlinson
|-
|Everett Wilson
|Michael Skilton
|-
|Rhett Rozga
|Dillon Gray
|-
|Greg Teiber
|Steven Finkelman
|-
| Jason Shanfield
| Ed Bennett
|-
|[[user:justin|Justin T. Conroy]]
|Ed Bennett
|-
|Bryan Gleason
|Dillon Gray
|-
|[[user:dwlocks|Dan Locks]]
|Dillon Gray
|-
|Sloan Lavery
|Ed Bennett
|-
|Casey Olson
|Ed Bennett
|-
|Todd Allen
|Ed Bennett
|-
|David Morton
|Ed Bennett
|-
|Thomas Wright
|Ed Bennett
|-
|George Shaw
|Thomas Wright
|-
|Rich Smith
|Thomas Wright
|-
|Tom Forajter
|Thomas Wright
|-
|Tyler Natoli
|Ed Bennett
|-
|Michael Leinartas
|Ed Bennett
|-
|Kyle Bieneman
|Todd Allen
|-
|Scott Little
|Todd Allen
|-
|RJ Metzger
|Todd Allen
|-
|Giovanni Arroyo
|Todd Allen
|-
|Joao Santos
|Todd Allen
|-
|Nicholas Haldereman
|Todd Allen
|-
|Doorman Dave
|Todd Allen
|-
|Stephen Ioannou
|Todd Allen
|-
|Lucas Goossen
|Todd Allen
|-
|[[user:RogerMoore|Roger Moore]]
|Todd Allen
|-
|[[User:Mwilkens|Matt Wilkens]]
|Todd Allen
|-
|Rhonda Jackson
|Todd Allen
|-
|Matt Meshulam
|Todd Allen
|-
|Kevin Pulver
|Todd Allen
|-
|Andrew Camardella
|Todd Allen
|-
|Mike Coriale
|Todd Allen
|-
|Nick Naro
|Todd Allen
|-
|John Farmer
|Todd Allen
|-
|[[user:Jaypee|Jay Pee]]
|Todd Allen
|-
|Sam Paris
|Todd Allen
|-
|Jake Rush
|Todd Allen
|-
|Carolyn Ignacio
|Todd Allen
|-
|Andrew Sowa
|Todd Allen
|-
|Hilary Lee
|Todd Allen
|-
|Eric Slehofer
|Todd Allen
|-
|Sam Reicks
|Todd Allen
|-
|Tyler Matthew
|Todd Allen
|-
|Ben Bogler
|Todd Allen
|-
|Brittany Krawczyk
|Todd Allen
|-
|Cary Lahucik
|Todd Allen
|-
|Eric Yu
|Todd Allen
|-
|Davis Mazariegos
|Todd Allen
|-
|Dan Baltudis
|Todd Allen
|-
|Ryan Taylor
|Everett Wilson
|-
|Andy Richardson
|Everett Wilson
|-
|David Srebro
|Todd Allen
|-
|Shae Kurko
|Todd Allen
|-
|[[User:glenn|Glenn Powers]]
|Todd Allen
|-
|Ryan Neuman
|Everett Wilson
|-
|Jeff Lawson
|Ron Olson
|-
|James Villalpando
|Ron Olson
|-
|Pericles Tsellos
|Todd Allen
|14JUN2015
|-
|Hunter Koerner
|Todd Allen
|6/14/15
|-
|-
|Erik Wessing
|Todd Allen
|-
|Eric Reusche
|Todd Allen
|-
|Raj Perera
|Todd Allen
|6/14/15
|-
|Jim Baker
|Todd Allen
|-
|Kevin Sampson
|Todd Allen
|7/22/15
|-
|Tom Boeman
|Todd Allen
|8/30/15
|-
|Jonathan Levine
|Todd Allen
|9/23/15
|-
|Alejandro Drexler
|Todd Allen
|9/23/15
|-
|Niko Hawley
|Todd Allen
|-
|Will Alt
|Todd Allen
|10/28/15
|-
|Peter Letscher
|Todd Allen
|10/28/15
|-
|-Caleb Young
|-Eric Beauchamp
|-
|Aaron Carlock
|Todd Allen
|11/18/15
|-
|Jennie P
|Todd Allen
|11/18/15
|-
|Kurt Ziegel
|Todd Allen
|11/18/15
|-
|Mike Forkan
|Todd Allen
|11/18/15
|-
|Elizabeth Arundel
|Todd Allen
|10/28/15
|-
|Jean Michel Crettaz
|Todd Allen
|-
|Bruce McConachie
|Michael Patton
|1/10/16
|-
|Andrew Dalesandro
|Michael Patton
|1/10/16
|-}

[[Category:Shop Equipment]]
[[Category:Metalworking]]
[[Category:Coldmetals]]

DoAll Bandsaw

2016-01-15T21:09:13Z

Andrewd: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = no
|model = DoAll 16-2
|serial = 45-55525
|arrived = 9/19/14
|doesitwork = yes
|contact = Dean Anderson
|where = machine shop
|value = 900
|image = DoAllMetalBandsaw.jpg
|hostarea = Coldmetals
}}

'''This tool requires certification for use.'''

== Specifications ==
{| class="wikitable" border="1"
|Capacity
|16" from the blade to the column
|-
|Blade Size
|120" blade. Width up to 1". Each width requires a set of hardened steel guides and a holder. See below for the guides we have.
|-
|Blade Speed
|approximately 45 to 1600 FPM, continuously variable.
|-
|Power
|240V, 3 phase
|-
|Weight
|1500-2000 pounds
|-
|Mfg. Date
|1955
|-
|}

== Auth/Use Notes ==
These notes are for authorized users and authorizers; you must be authorized on the tool by a person, not this list. Don't expect this list to be complete or authoritative.

* Vertical band saws cut by feeding the material into the blade.
** The cutting tooth speed is set by spinning the speed adjustment handle.
** Selection between high and low gear is only done when the adjustment handle is spun to the slowest possible speed. Don't force the gear selection; wiggle it into place.
** Only adjust the speed when the machine is on.
** The speed read out is on the dial on the top left part of the machine.
** ''Always'' check the speed versus your material via the read out before making any cuts. Incorrect speeds will quickly ruin blades.
* The cutting feed is set by you, pushing the material into the blade.
** There is a half-circle with steps for workholding and handles to control the piece. Use it whenever possible.
** If cutting curves, check the width of the blade against the chart for the tightest corner you can cut.
** If you're attempting to cut an angle, start by feeding the workpiece directly into the saw to form a notch first.
** The angle of the table can be changed after loosening the knob on the right side of the machine and below the table. Then tilt the table by hand. You may have to adjust the height of the lower blade guide if you tilt the table far from horizontal.
** If the blade is drifting to one side, it might be dulling.
** Ensure that you have between 3 and 24 teeth engaged with the thickness of the workpiece. Too few and you will knock teeth off; too many and you will fail to form a satisfactory chip.
* Power
** The plug is a twist-lock 220V three-phase plug.
** The starter is a grey box on the back of the machine. Press the rocker to display "ON".
** Turn the key to the "on" position.
** Use the larger side buttons to start the machine. The on button may require multiple presses.
** Always hit the red stop button when you're not actively cutting.
** Set the starter to off and unplug the machine when you're finished.
* Safety
** Never put your fingers near the blade. If your part is too small to keep your fingers at least an inch away from the blade and can't be held in the half-circle workholder, design a way to safely hold the workpiece that doesn't put your fingers near the blade.
** Lower the blade guard as much as possible; there should be a narrow gap above the workpiece and no more.
** No gloves or loose sleeves when using the machine; they can be sucked into the blade and drag your arm with. Pushing your sleeves past your shoulder is not acceptable.
** When pushing work, rest your arms on the table and push with your hands. Pushing with your shoulders can cause you to fall into the machine if the blade breaks or the part slips.
** Stand with one foot in front of the other to prevent bashing your head or chest into the machine if you do lose control with your arms.
* Clean up when you're done. Remove your stock and brush all chips into a trash can. Wipe up all cutting fluids.

== Blades ==
Installed:

== Welder ==

The welder is finally functioning. It can be used for blades for any of the bandsaws. So far, we have just welded carbon blades. Bimetal may be difficult- brazing might be a better choice for these. Talk to Ed Bennett or Everett Wilson if you want to learn how to use the welder. The procedure is:
#Measure 120" (5 table lengths) of the bulk blade of your choice.
#Cut the blade to length using the shear above the welder.
#Match the cut ends together with the teeth on each end pointing in opposite directions (180 degree twist in the blade). Grind the ends of the blade until they match and are smooth. Normally you could use the grinder on the welder, but the grinder is not working.
#Clamp the blade in the jaws with the ends of the blade touching.
#Push the welder lever down and hold it down. After the weld is done, release one of the jaw clamps, then release the welder lever.
#Anneal the blade until dull red (pulse width modulate the anneal button - it doesn't take much).
#Grind the weld until smooth and the weld thickness is the same as the blade.

== To-Do ==

Blade welder is missing the grinder motor. The shear for the welder is not making clean cuts.

Add a miter jig which mounts to the right side of the table. A round linear bearing would allow the jig to be tilted down out of the way when not in use.

== Maintenance ==
{| class="wikitable" border="1"
! Description
! Frequency
! Lubricant
! Instructions
! History
|-
|
|
|
|
|
|-
|Gear Box
|
|The manual for model 16-2 (our saw) says to use SAE 10 motor oil. The manual for the 1612 (a slightly newer model) says SAE 20. DoAll support says use SAE 20 motor oil, which is difficult to find. ISO 68 waylube is equivalent to SAE 20 and available from Zengers in Melrose Park.
| The drain plug is at the bottom of the gear box. Remove pipe cap and fill to the top of the pipe. Takes about 1 quart.
| Changed 10/7/14 with ISO 68. Only about 2 cups of oil were drained, but no sign of a leak.

|
|-
|Reeves drive shaft (oil cup)
|
| 1612: SAE 10
|
|
|}

Oct. 15, 2014 Replaced thrust bearings and bearing caps for the 1/16-1/2" upper and lower guides. With the blade centered on the wheel, there is a gap of about 1/8 between the cap and the back edge of the blade. With medium heavy hand feed, the blade doesn't touch the cap and cause the bearing to turn. This may be OK, as there would be significantly more pressure from the workpiece when using the machine's mechanical feed.

Tried the 5/8-1" guides. appears that there will also be a gap between the blade and thrust bearing cap when using a 3/4" blade with the blade centered on the wheel. For the upper guide, we need 2 longer cap screws (1/4-20?) to hold the 3/4" hardened guides to the guide block and 2 shorter screws (shoulder?) to hold the guide block to the guide post. For the lower guide, 2 cap screws. not sure about the screw that holds the lower guide block in place.

== Equipment ==
{| class="wikitable" border="1"
! Item
! Description
! Supplier
! Cost
|-
| Guide thrust bearing
| 626ZZ 6x19x6mm (2 required)
|
|
|-
| Guide Blocks
| Upper and lower insert guide blocks for 1/16-1/2" width blades ('precision' style); upper and lower insert guide blocks ('high speed' style) for 5/8" to 1" width blades.
|
|
|-
| Inserts
| Sets of 4 hardened steel inserts for 1/4", 3/8", 1/2", 3/4".
|
|
|-
|Adapter
|We have the upper and lower Adapters for 1/16 to 1/2" guide blocks.
|
|
|}

== References ==

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
!Date Trained
|-
|Dean Anderson
|Machine Shop Host Cred
|
|-
|Everett Wilson
|Dean Anderson
|
|-
| Ed Bennett
| Dean Anderson
|
|-
|Ryan Pierce
|Dean Anderson
|
|-
|Bryan Gleason
|Dean Anderson
|
|-
|Michael Czubak
|Dean Anderson
|
|-
|Todd Allen
|Dean Anderson
|
|-
| Anna Yu
| Ed Bennett
|
|-
|Jeff McBride
|Ed Bennett
|10/9/14
|-
|Mike Kislovsky
|Ed Bennett
|10/9/14
|-
|Arjun Wadnerkar
|Ed Bennett
|10/9/14
|-
|Oscar Villareal
|Ed Bennett
|10/9/14
|-
|John Butera
|Ed Bennett
|10/18/14
|-
|Alex Schaffer
|Ed Bennett
|10/18/14
|-
|Daniel Loeser
|Ed Bennett
|10/18/14
|-
|Jonathan Bisson
|Ed Bennett
|10/18/14
|-
|[[User:amishhammer|Tom Judge]]
|Todd Allen
|
|-
|Kyle Bieneman
|Todd Allen
|11/09/14
|-
|Scott Little
|Todd Allen
|11/09/14
|-
|RJ Metzger
|Todd Allen
|11/09/14
|-
|Giovanni Arroyo
|Todd Allen
|11/09/14
|-
|Joao Santos
|Todd Allen
|11/26/14
|-
|Nicholas Haldereman
|Todd Allen
|11/26/14
|-
|Doorman Dave
|Todd Allen
|11/26/14
|-
|Stephen Ioannou
|Todd Allen
|11/26/14
|-
|Lucas Goossen
|Todd Allen
|12/10/14
|-
|[[user:RogerMoore|Roger Moore]]
|Todd Allen
|12/10/14
|-
|[[User:Mwilkens|Matt Wilkens]]
|Todd Allen
|12/10/14
|-
|Rhonda Jackson
|Todd Allen
|12/10/14
|-
|Matt Meshulam
|Todd Allen
|12/21/14
|-
|Kevin Pulver
|Todd Allen
|12/21/14
|-
|Andrew Camardella
|Todd Allen
|12/21/14
|-
|Mike Coriale
|Todd Allen
|12/21/14
|-
|Nick Naro
|Todd Allen
|1/11/15
|-
|John Farmer
|Todd Allen
|1/11/15
|-
|[[user:Jaypee|Jay Pee]]
|Todd Allen
|1/11/15
|-
|Sam Paris
|Todd Allen
|1/21/2015
|-
|Jake Rush
|Todd Allen
|1/21/2015
|-
|Carolyn Ignacio
|Todd Allen
|1/21/2015
|-
|Andrew Sowa
|Todd Allen
|1/21/2015
|-
|Hilary Lee
|Todd Allen
|1/21/2015
|-
|Eric Slehofer
|Todd Allen
|1/28/2015
|-
|Sam Reicks
|Todd Allen
|1/28/2015
|-
|Tyler Matthew
|Todd Allen
|1/28/2015
|-
|Ben Bogler
|Todd Allen
|1/28/2015
|-
|Brittany Krawczyk
|Todd Allen
|1/28/2015
|-
|Cary Lahucik
|Todd Allen
|1/28/2015
|-
|Eric Yu
|Todd Allen
|2/8/2015
|-
|Davis Mazariegos
|Todd Allen
|2/8/2015
|-
|Dan Baltudis
|Todd Allen
|2/8/2015
|-
|Shae Kurko
|Todd Allen
|2/25/2015
|-
|Ryan Taylor
|Everett Wilson
|03/04/15
|-
|Andy Richardson
|Everett Wilson
|03/04/15
|-
|[[User:glenn|Glenn Powers]]
|Sevin Straus
|03/08/15
|-
|Ryan Neuman
|Sevin Straus
|3/08/15
|-
|Simon Cygielski
|Todd Allen
|20150407
|-
|[[User:papaben44|Benjamin Dambman]]
|Matt Triano
|4/14/15
|-
|Jeff Lawson
|Ron Olson
|5/19/15
|-
|David Srebro
|Ron Olson
|5/19/15
|-
|James Villalpando-
|Ron Olson
|5/19/15
|-
|[[user:justin|Justin T. Conroy]]
|Everett Wilson
|2015/06/10
|-
|Greg "Nerobro" Teiber
|Everett Wilson
|2015/06/10
|-
|Pericles Tsellos
|Todd Allen
|14JUN2015
|-
|Hunter Koerner
|Todd Allen
|6/14/15
|-
|Eric Reusche
|Todd Allen
|6/14/15
|-
|Raj Perera
|Todd Allen
|6/14/15
|-
|Erik Wessing
|Todd Allen
|6/14/15
|-
|Connor Jansen
|Eric Beauchamp
|6/4/15
|-
|Kevin Sampson
|Todd Allen
|7/22/15
|-
|Les Schier
|Dean Anderson
|-
|Tom Boeman
|Todd Allen
|8/30/15
|-
|Jonathan Levine
|Todd Allen
|9/23/15
|-
|Jim Baker
|Todd Allen
|-
|Alejandro Drexler
|Todd Allen
|9/23/15
|-
| Sheila Miguez
| Everett Wilson
| 10/14/2015
|-
|Niko Hawley
|Todd Allen
|-
|Will Alt
|Todd Allen
|10/28/15
|-
|Peter Letscher
|Todd Allen
|10/28/15
|-
|Mike Mandrea
|Eric Beauchamp
|11/5/15
|-
|-Caleb Young
|-Eric Beauchamp
|-
|Aaron Carlock
|Todd Allen
|11/18/15
|-
|Jennie P
|Todd Allen
|11/18/15
|-
|Kurt Ziegel
|Todd Allen
|11/18/15
|-
|Mike Forkan
|Todd Allen
|11/18/15
|-
|Marcin Ignasiak
|Todd Allen
|-
|Greg Kudlacz
|Todd Allen
|-
|Daniel Maziarz
|Todd Allen
|-
|Jean Michel Crettaz
|Todd Allen
|-
|Dafe Hughes|Dafe Hughes
|Todd Allen
|12/16/15
|-
|Bruce McConachie
|Michael Patton
|1/10/16
|-
|Andrew Dalesandro
|Michael Patton
|1/10/16
|-
}

[[Category:Metalworking]]
[[Category:Coldmetals]]

Johnson Bandsaw

2016-01-15T21:08:43Z

Andrewd: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = no
|model = Johnson Model J (JD)
|serial = J14445
|arrived = 1/13/14
|doesitwork = yes
|contact = Dean Anderson
|where =
|value = 700
|image =JohnsonMetalBandsaw.jpg
|hostarea = Coldmetals
}}

== Status ==

* One phase of the starter is working intermittently. We cleaned the contacts of the starter, but this didn't fix the problem. If the motor is making noise and not turning, turn the starter on the back of the saw 'off' and then 'on. If the problem persists, leave the saw off. We should replace the starter.

* The large groove (fastest speed) of the motor shaft step pulley is bent. The motor vibrates excessively when the belt is in this groove. Use the other grooves (slower speeds) until the pulley is replaced.

'''This tool requires certification for use.'''

Johnson products are now supported by Dake. http://www.dakecorp.com/ Replacement parts for this saw are generally available.

== Specifications ==
{| class="wikitable" border="1"
|Capacity
|10" rounds, 18" flats
|-
|Blade Size
|137" x 3/4"
|-
|Blade Speed
|35, 90, 130, 190 FPM
|-
|Power
|240V, 3 phase
|-
|Weight
|683 pounds
|-
|Mfg. Date
|1964
|-
|}

== Blades ==
General rule of thumb is that if the thinnest part (in the direction of the blade) that you're cutting isn't at least 3 saw teeth thick, it will damage the blade.

== To-Do ==

Grease pivot bar

Add coolant pan and pump.

Add blade brush.

Put FPM from the machine's sticky note on here.

== Maintenance ==
{| class="wikitable" border="1"
! Description
! Frequency
! Lubricant
! Instructions
! History
|-
|Hydraulic cylinder
|Maintain level at top of oil cup.
|
|
|
|-
|Gear Box
|yearly
|80W-90 gear oil
|Drain and fill with 3 ounces of oil.
Requires removing gearbox. See below.
|2/14 8 oz 85W90
|-
|Pivot bar
|monthly
|General purpose grease
|2 Zert fittings. Use grease gun.
|
|}
Gearbox oil change. Loosen 2 screws on the left edge of right top cover. Remove top 2 screws on the right side. Loosen bottom 2 screws on the right side cover. Slide top cover towards the center of the saw. Pivot the right cover down. Remove drive belt. Remove gearbox step pulley. Remove 3 bolts holding the gearbox. These are near the ring gear teeth. Remove the gearbox out the top of the saw between the two transverse brackets (long shaft comes out last). Drain/fill bolt is on the side opposite the pinion gear. Consider replacing the gaskets on the gearbox.

== Auth/Use Notes ==
These notes are for authorized users and authorizers; you must be authorized on the tool by a person, not this list. Don't expect this list to be complete or authoritative.

* Horizontal band saws cut via a vertically descending blades.
* The cutting tooth speed is set by a pulley in the rear.
** Lift up on the motor to get some slack on the belt.
** Don't cross wheels; keep the pulley belt straight.
** Go toward larger motor wheels for soft metals and plastic and smaller motor wheels for tough metals like steel (and tool steel.)
* The cutting tooth feed is set by a needle valve and a weight on top.
** Be gentle with the needle valve; a single finger with light pressure is enough to adjust it.
* Power
** The plug is a twist-lock 220V three-phase plug.
** The starter is located on the back. If you turn on the machine and it makes a buzzing noise, turn it off immediately and turn off/on the starter.
** During use, the on/off switch at the end of the machine is used for power. The trip lever also activates this same switch.
** Turn off switches and unplug the machine when you're done to prevent accidental activation.
** Never walk away from the machine while it's running. We are not a production shop; babysit the machine in case it fails and avoid putting curious people in danger.
* Clamping a workpiece
** Short pieces cock the vice jaws. This ruins the grip on the workpiece and is to be avoided.
** Use a similarly wide piece on the other side of the vice jaw to prevent the jaw from cocking.
** Check the width of your workpiece against the teeth.
*** The thinnest section of the workpiece should be wider than three teeth in a row.
*** The thickest section of the workpiece should be narrow than twenty-four teeth.
** If you're cutting angle stock, rotate it so that it forms a < shape to prevent it from rotating.
** If you're cutting round, use angle blocks (in the tooling cabinet) to keep it from rotating.
** Check that the movable blade guide is as close as possible while clearing the vice and the table.
* Safety
** Unplug the machine before adjusting the pulley or changing the blade.
** Never leave the machine while running. We aren't a production shop; you need to be right by the machine in case something goes wrong or if a curious person walks by.
* Clean up when you're done. Don't leave stock in the machine; don't leave chips and coolant behind. Use a small bucket to catch chips before they hit the ground.

== References ==

Manual for the latest version of the Model J (very similar).

http://www.dakecorp.com/manuals/Model%20Johnson%20J%20Saws.pdf

Good link for restoration, including coolant pan dimensions and bearing sizes. http://www.shopfloortalk.com/forums/showthread.php?t=21021

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
|-
|Dean Anderson
|
|-
|Todd Allen
|Ed Bennet
|-
|David Morton
|Anna Yu
|-
|George Shaw
|Thomas Wright
|-
|bandit Gangwere
|Ed Bennet
|-
|Michael Skilton
|Tucker
|-
|Eric Stein
|Tucker
|-
|Kyle Bieneman
|Todd Allen
|-
|Scott Little
|Todd Allen
|-
|RJ Metzger
|Todd Allen
|-
|Giovanni Arroyo
|Todd Allen
|-
|Mark C.
|Todd Allen
|-
|Joao Santos
|Todd Allen
|-
|Nicholas Haldereman
|Todd Allen
|-
|Doorman Dave
|Todd Allen
|-
|Stephen Ioannou
|Todd Allen
|-
|Lucas Goossen
|Todd Allen
|-
|[[user:RogerMoore|Roger Moore]]
|Todd Allen
|-
|[[User:Mwilkens|Matt Wilkens]]
|Todd Allen
|-
|Rhonda Jackson
|Todd Allen
|-
|Matt Meshulam
|Todd Allen
|-
|Kevin Pulver
|Todd Allen
|-
|Andrew Camardella
|Todd Allen
|-
|Mike Coriale
|Todd Allen
|-
|John Farmer
|Todd Allen
|-
|[[user:Jaypee|Jay Pee]]
|Todd Allen
|-
|Sam Paris
|Todd Allen
|-
|Jake Rush
|Todd Allen
|-
|Carolyn Ignacio
|Todd Allen
|-
|Andrew Sowa
|Todd Allen
|-
|Hilary Lee
|Todd Allen
|-
|Eric Slehofer
|Todd Allen
|-
|Sam Reicks
|Todd Allen
|-
|Tyler Matthew
|Todd Allen
|-
|Ben Bogler
|Todd Allen
|-
|Brittany Krawczyk
|Todd Allen
|-
|Cary Lahucik
|Todd Allen
|-
|Eric Yu
|Todd Allen
|-
|Davis Mazariegos
|Todd Allen
|-
|Dan Baltudis
|Todd Allen
|-
|Ryan Taylor
|Everett Wilson
|-
|Andy Richardson
|Everett Wilson
|-
|David Srebro
|Todd Allen
|-
|Shae Kurko
|Todd Allen
|-
|Simon Cygielski
|Todd Allen
|-
|Jeff Lawson
|Ron Olson
|-
|James Villalpando
|Ron Olson
|5/19/15
|-
|Greg "Nerobro" Teiber
|Everett Wilson
|-
|Pericles Tsellos
|Todd Allen
|14JUN2015
|-
|Hunter Koerner
|Todd Allen
|6/14/15
|-
|Eric Reusche
|Todd Allen
|-
|Raj Perera
|Todd Allen
|6/14/15
|-
|Erik Wessing
|Todd Allen
|-
|Ryan Neuman
|Ron Olson
|-
|Kevin Sampson
|Todd Allen
|7/22/15
|-
|Jim Baker
|Todd Allen
|-
|Tom Boeman
|Todd Allen
|8/30/15
|-
|Jonathan Levine
|Todd Allen
|9/23/15
|-
|Alejandro Drexler
|Todd Allen
|9/23/15
|-
| Sheila Miguez
| Everett Wilson
| 10/14/2015
|-
|Niko Hawley
|Todd Allen
|-
|Will Alt
|Todd Allen
|10/28/15
|-
|Peter Letscher
|Todd Allen
|10/28/15
|-
|Aaron Carlock
|Todd Allen
|11/18/15
|-
|Jennie P
|Todd Allen
|11/18/15
|-
|Kurt Ziegel
|Todd Allen
|11/18/15
|-
|Mike Forkan
|Ron Olson
|11/18/15
|-
|Marcin Ignasiak
|Ron Olson
|-
|Greg Kudlacz
|Todd Allen
|-
|Daniel Maziarz
|Todd Allen
|-
|-
|Jean Michel Crettaz
|Todd Allen
|12/14/15
|-
|Dafe Hughes
|Todd Allen
|12/16/15
|-}
|Bruce McConachie
|Michael Patton
|1/10/16
|-
|Andrew Dalesandro
|Michael Patton
|1/10/16
|-}
[[Category:Metalworking]]
[[Category:Coldmetals]]

Laguna 16" Planer

2016-01-15T21:06:38Z

Andrewd: /* List of currently authorized users */

{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = no
|model = MPLAN1510-0120
|serial = 144367
|arrived =
|doesitwork = yes
|contact =
|where = Woodshop
|value = $3000
|image = LagunaPlaner.jpg
|hostarea = Woodworking
}}

== Rules ==
# '''Always''' check your wood for nails or staples. Something as small as the staple at the end of a 1x1 can ruin the blades. If you're not sure, check the entire piece with the metal detector sitting on the table saw.
# '''Always''' measure the thickness of your work and set the initial and working blade height to remove only small amounts of material per pass. You will damage the blades if you manage to dig the machine out on your work. If it sounds weird, '''You're Not Doing It Right''' and you need to ask for help.
# If the blades are dull or damaged, '''contact the area host immediately'''. Don't be a dick and let others ruin their work because you didn't say anything.
# If you break something, or damage the tool, '''contact the area host immediately'''. Don't let others do more damage or hurt themselves by using a broken tool.
# '''Always''' make sure that the dust collection bag isn't too full and is passing air freely.
# '''Always''' vacuum the machine, cutting area, and the table around the machine when you are done.

'''This tool requires authorization for use.'''

{{WoodshopProctors}}

== List of currently authorized users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
|-
|Matt Triano
|Danger committee
|-
|Eric Beauchamp
|Danger committee
|-
|Jason Shanfield
|Matt Triano
|-
|Tom Judge
|Matt Triano
|-
|Hunter Koerner
|Eric Beauchamp
|-
|Deanna Williams
|Eric Beauchamp
|-
|Casey Olson
|Eric Beauchamp
|-
|Burton Kent
|Eric Beauchamp
|-
|Jeff Smykil
|Matt Triano
|-
|Anna Yu
|Jason Shanfield
|-
|Todd Allen
|Ron Olson
|-
|Jon Levine
|Jason Shanfield
|-
|Kyle Bieneman
|Eric Beauchamp
|-
|Niko Hawley
|Eric Beauchamp
|-
|-
|Adam Moffatt
|Eric Beauchamp
|-
|Marcin Ignasiak
|Eric Beauchamp
|-
|Keon Turner
|Ron Olson
|-
|Mike Mandrea
|Eric Beauchamp
|-
|-Caleb Young
|-Eric Beauchamp
|-
|Erik Wessing
|Eric Beauchamp
|-
|Peter Letscher
|Eric Beauchamp
|11/05/15
|-
|Glenn Trussell
|Eric Beauchamp
|11/05/2015
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Shine Chen
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/03/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Chris Kohl
|Eric Beauchamp
|1/8/2016
|-
|Szymon Sambor
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Peter Brask
|Eric Beauchamp
|1/14/16
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
}

Porter-Cable Router Table

2016-01-15T21:06:15Z

Andrewd: /* List of Currently Certified Users */

== Router ==

{{Template:EquipmentPage
| image = Router-table.jpg
|owner = PS:One
|serial =
|certification = yes
|hackable = no
|model =
|arrived =
|doesitwork = yes
|contact =
|where = Woodshop
|hostarea = Woodworking
|value =
}}

'''This tool requires authorization for use.'''

{{WoodshopProctors}}

== List of Currently Certified Users ==
{| class="wikitable" border="1"
! Qualified Member Keon Turner
! Trained By Ron Olson
! Date Certified 10/19/15
|-
|Marcin Ignasiak
|Eric Beauchamp
|-
|Tim Saylor
|Danger Committee
|-
|Dillon Gray
|Danger Committee
|-
|Shawn Blaszak
|
|-
|Adrianna McKinley
|Tim Saylor
|-
|Kathy Whisler
|Tim Saylor
|-
|James Longfield
|Tim Saylor
|-
|Eric Veggeberg
|Tim Saylor
|-
| Madeleine Klichowski
| Tim Saylor
|-
| Lyn Cole
| Tim Saylor
|-
| Nathan Becka
| Tim Saylor
|-
| Brian Carstensen
| Tim Saylor
|-
| Matt Triano
| Tim Saylor
|-
|Bryan Gleason
|Matt Triano
|-
|Daniel Wells
|Matt Triano
|-
|Sean Corbett
|Matt Triano
|-
|Michael Skilton
|Matt Triano
|-
|Aaron Feigen
|Matt Triano
|-
|Ryan Pierce
|Dan Locks
|-
|John Godwim
|Matt Triano
|-
|Nate Hutchins
|Matt Triano
|-
|Jeff Molek
|Matt Triano
|-
|Sloan Lavery
|Matt Triano
|-
|Trey Keifer
|Matt Triano
|-
|Juan Robles
|Matt Triano
|-
|Simon Cygielski
|Matt Triano
|-
|Tom Forajter
|Matt Triano
|-
|Robert Grossman
|Matt Triano
|-
|Lucas Morris
|Matt Triano
|-
|Sergio Preston
|Matt Triano
|-
|Ron Bean
|Matt Triano
|-
|Greg Eagel
|Matt Triano
|-
|Carter Constana
|Matt Triano
|-
|Adam Glick
|Matt Triano
|-
|Zachary Fietsch
|Matt Triano
|-
|Solomon Hursey
|Matt Triano
|-
|Jesse Reynolds
|Matt Triano
|-
|Eduard Shlahtichman
|Matt Triano
|-
|Skittles Rainbow
|Matt Triano
|-
|Tom Jurgensen
|Matt Triano
|-
|Barmey Ung
|Matt Triano
|-
|Casey Olson
|Matt Triano
|-
|Jonathan Bisson
|Matt Triano
|-
|Bandit Gangwere
|Matt Triano
|-
|Joseph Nudell
|Matt Triano
|-
|David Butler
|Matt Triano
|-
|Kathryn Smiley
|Matt Triano
|-
|Aimee Spevak
|Matt Triano
|-
|Cassie Webster
|Matt Triano
|-
|Chris Moylan
|Matt Triano
|-
|Mike O'Connor
|Matt Triano
|-
|Tyler Hsu
|Matt Triano
|-
|Dee Newcum
|Matt Triano
|-
|Zihe "Johnson" Luo
|Matt Triano
|-
|Giovanni Arroyo
|Matt Triano
|-
|Nathan Ellis
|Matt Triano
|-
|Ian McLeod
|Nathan Ellis
|-
|Brandon Price
|Matt Triano
|-
|Arturo Duarte
|Matt Triano
|-
|Eric Braun
|Matt Triano
|-
|Jeremy Fay
|Matt Triano
|-
|Leeswann Bolden
|Matt Triano
|-
|James Porter
|Matt Triano
|-
|Jeff McBride
|Matt Triano
|-
|Connor Miller
|Matt Triano
|-
|Ashley Duca
|Matt Triano
|-
|Karen Niemczyk
|Matt Triano
|-
|Bassam Alshammari
|Matt Triano
|-
|John Fiene
|Matt Triano
|-
|Thomas Wright
|Matt Triano
|-
|Joseph Peltier
|Matt Triano
|-
|Justin Conroy
|Matt Triano
|-
|David Koppel
|Matt Triano
|-
|Sevin Straus
|Matt Triano
|-
|Roger Moore
|Matt Triano
|-
|Valerie Moore
|Matt Triano
|-
|Andy Schwartz
|Matt Triano
|-
|Assaf Evron
|Matt Triano
|-
|David Pelot
|Matt Triano
|-
|Rich Smith
|Matt Triano
|-
|Khoi Nguyen
|Matt Triano
|-
|Brian Keehner
|Matt Triano
|-
|Jesse Gare
|Matt Triano
|-
|Tyler Natoli
|Matt Triano
|-
|David Siegfried
|Matt Triano
|-
|Annie Zebula
|Matt Triano
|-
|Eliya Gwetta
|Matt Triano
|-
|Patrick Schliss
|Matt Triano
|-
|Arjun Wadnerkar
|Matt Triano
|-
|Touly Phiachantharath
|Matt Triano
|-
|Matt Vibberts
|Matt Triano
|-
|Thomas Garza
|Matt Triano
|-
|Will Garza
|Matt Triano
|-
|Brennan Koziarz
|Matt Triano
|-
|Alec Weege
|Matt Triano
|-
|Eric Beauchamp
|Matt Triano
|-
|Clarence Risher
|Matt Triano
|-
|Erica Tesla
|Matt Triano
|-
|Jabu Dawdu
|Matt Triano
|-
|Karen Murphey
|Matt Triano
|-
|Matt Meshulam
|Matt Triano
|-
|Josh Myers
|Matt Triano
|-
|Weston Tanner
|Matt Triano
|-
|Hugh Sato
|Matt Triano
|-
|Nora Sluzas
|Matt Triano
|-
|Elizabeth Koprucki
|Matt Triano
|-
|Oscar Villareal
|Matt Triano
|-
|Rob Paral
|Matt Triano
|-
|Alex Schaffer
|Matt Triano
|-
|Szymon Sambor
|Matt Triano
|-
|Michael Solhelm
|Matt Triano
|-
|[[User:lucas|Lucas Goossen]]
|Matt Triano
|-
|[[User:Mwilkens|Matt Wilkens]]
|Matt Triano
|-
|Eric Slehofer
|Matt Triano
|-
|Jon Levine
|Matt Triano
|-
|Melody Snyder
|Matt Triano
|-
|Curtis Cooke
|Matt Triano
|-
|Harry Morgan
|Matt Triano
|-
|Sam Drazin
|Matt Triano
|-
|Mike Kislovsky
|Matt Triano
|-
|Keven Kalay
|Matt Triano
|-
|Sam Reicks
|Ron Olson
|-
|Kevin Pulver
|Ron Olson
|-
|Cary Lahucik
|Ron Olson
|-
|Keith Hultman
|Ron Olson
|-
|Mario Rodriguez
|Ron Olson
|-
|John Keippel
|Ron Olson
|-
|Szilvia Precsinszki
|Ron Olson
|-
|Davis Mazariegos
|Ron Olson
|-
|Pete Noverini
|Matt Triano
|-
|Mike Coriale
|Matt Triano
|-
|Dan Baltudis
|Ron Olson
|-
|David Fell
|Ron Olson
|-
|Dubi Kaufmann
|Ron Olson
|-
|Patrick Grider
|Ron Olson
|-
|Tyler Matthew
|Matt Triano
|-
|Shae Kurko
|Matt Triano
|-
|John Farmer
|Ron Olson
|-
|Sam Paris
|Ron Olson
|-
|Frances Ritchie
|Ron Olson
|-
|Ben Kern
|Ron Olson
|-
|Eric Yu
|Ron Olson
|-
|Knute Martell
|Ron Olson
|-
|Karol Slowikowski
|Ron Olson
|-
|Chris Smith
|Ron Olson
|-
|Benjamin Miller
|Ron Olson
|-
|Jennie P
|Ron Olson
|-
|Eugene Liokumovich
|Ron Olson
|-
|Laurel Garrett
|Matt Triano
|-
|Rei Kevin
|Matt Triano
|-
|Aji Slater
|Matt Triano
|-
|John Beyer
|Matt Triano
|-
|Brad Topol
|Matt Triano
|-
|[[User:papaben44|Benjamin Dambman]]
|Matt Triano
|4/14/2015
|-
|Tomas Ward
|Ron Olson
|4/26/2015
|-
|Les Schier
|Jason Shanfield
|5/2/15
|-
|Andy Richardson
|Matt Triano
|4/14/15
|-
|Erik Wessing
|Eric Beauchamp
|-
|Ryan Neuman
|Ron Olson
|-
|Anthony Phelps
|Eric Beauchamp
|8/27/2015
|-
|Ralph Brendler
|Eric Beauchamp
|8/27/2015
|-
|Jim Baker
|Eric Beauchamp
|8/27/2015
|-
|Kyle Bieneman
|Ron Olson
|-
|Glenn Powers
|Jason Shanfield
|10/18/2015
|-
|Niko Hawley
|Eric Beauchamp
|-
|Kevin Mitchell
|Eric Beauchamp
|-
|[[User:themoffatt|Adam Moffatt]]
|Eric Beauchamp
|10/22/2015
|-
|Jean Michel Crettaz
|Eric Beauchamp
|10/22/2015
|-
|-Caleb Young
|-Eric Beauchamp
|-
|Peter Letscher
|Eric Beauchamp
|11/05/15
|-
|Glenn Trussell
|Eric Beauchamp
|11/05/2015
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Shine Chen
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/03/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Chris Kohl
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Peter Brask
|Eric Beauchamp
|1/14/16
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
}

[[Category:Shop Equipment]]
[[Category:Fabrication]]
[[Category:Woodworking]]

Belt Sander

2016-01-15T21:05:15Z

Andrewd: /* List of Currently Certified Users */

{{Template:EquipmentPage
|owner = Steve
|certification = YES
|hackable = NO
|model = MODEL NUMBER
|serial = SERIAL NUMBER
|arrived = 12/01/11
|doesitwork = yes
|contact = Adrianna
|where = [[Woodshop|Workshop]]
|value = DOLLARS
|image = beltsander.jpg
}}
== List of Currently Certified Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
|-
|Gabriel Rosenhouse
|Adrianna McKinley
|-
|Mike Warot
|Adrianna McKinley
|-
|Ryan Pierce
|Internship
|-
|Jason Shanfield
|Matt Triano
|-
|Nathan Ellis
|Jason Shanfield

|-
|[[User:Dee|Dee]]
|[[User:Toba|Eric Stein]]
|-
|[[User:Justin|Justin T. Conroy]]
|Ed Bennett
|-
|Sloan Lavery
|Ed Bennett
|-
|David Fell
|Ron Olson
|-
|Patrick Grider
|Ron Olson
|-
|Chris Kleehammer
|[[User:jason|Jason Shanfield]]
|-
|Trey Elliott
|[[User:jason|Jason Shanfield]]
|-
|Nik Brink
|[[User:jason|Jason Shanfield]]
|-
|Frances Ritchie
|Ron Olson
|-
|Eric Yu
|Ron Olson
|-
|Benjamin Miller
|Ron Olson
|-
|David Srebro
|Ron Olson
|-
|James Villalpando
|Ron Olson
|-
|Jeff Lawson
|Ron Olson
|-
|Tomas Ward
|Ron Olson
|4/26/2015
|-
|Anthony Phelps
|Eric Beauchamp
|8/27/2015
|-
|-Caleb Young
|-Eric Beauchamp
|-
|Aaron Carlock
|Ron Olson
|11/18/15
|-
|Greg Kudlacz
|Ron Olson
|-
|Daniel Maziarz
|Ron Olson
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
}

[[Category:Equipment]]
[[Category:Shop Equipment]]

Sears Scroll Saw

2016-01-15T21:04:28Z

Andrewd: /* List of Currently Certified Users */

{{Template:EquipmentPage
|owner = PS:One
|model = Sears/Craftsman 137.216160
|serial = RFW11
|arrived = April 2009
|doesitwork = yes
|contact = Dan Meyer
|where = Wood Shop
|certification = yes
|hackable = no
|value = $100
|hostarea = Woodworking
|image = Sears_scroll_saw_small.jpg
}}

{{WoodshopProctors}}

== Documentation ==
* [http://www.managemylife.com/mmh/lis_pdf/OWNM/L0808290.pdf Owner's manual]

== List of Currently Certified Users ==
{| class="wikitable" border="1"
! Qualified Member Keon Turner
! Trained By Ron Olson
|-
|Adam Flynn
|Danger Committee
|-
|Julie Moffitt
|Danger Committee
|-
|Sacha De'Angeli
|Danger Committee
|-
|Eric Michaud
|Danger Committee
|-
|Dan Davis Bodeiaver?
|Danger Committee
|-
|Tim Saylor
|Danger Committee
|-
|Zane Bowers
|Danger Committee
|-
|Teddie Goldenberg
|Seth D. Slis?
|-
|Nicolle Nevlist
|Seth D. Slis?
|-
|Jeff Kantarek
|Eric Michaud
|-
|Chris Luiz
|Eric Michaud
|-
|Avner Shanan
|Chris Luiz
|-
|David Mole
|Tim Saylor
|-
|Sarah Sutherlin
|Jeff Kantarek
|-
|Jeannette Thraen
|Sarah Sutherlin
|-
|Jasna Delic
|Sarah Sutherlin
|-
|Nathan Witt
|?
|-
|Tom Ketola
|Nathan Witt
|-
|Geoffrey Topham
|Nathan Witt
|-
|John Stoner
|Nathan Witt
|-
|Ryan Lanham
|Nathan Witt
|-
|Brian Cordanvier
|Nathan Witt
|-
|Jim Burke
|Nathan Witt
|-
|Anne Petersen
|Nathan Witt
|-
|Cory Knapp
|Nathan Witt
|-
|Joshua Rothhaas
|Shawn Blaszak
|-
|Jay Hopkins
|Shawn Blaszak
|-
|Jordan Bunker
|Nathan Witt
|-
|Constomtin Gowileson?
|Nathan Witt
|-
|Alek Shnayder
|Nathan Witt
|-
|John Dorfman
|Nathan Witt
|-
|Jakub Klimuszko
|Sacha De'Angeli
|-
|Adrianna McKinley
|?
|-
|Nathan Witt
|Adrianna McKinley
|-
|Bryer Le?
|Eric Michaud
|-
|Matt Bran
|Shawn Blaszak
|-
|Nick Ferrari
|Tim Saylor
|-
|Chris Fanning
|Shawn Blaszak
|-
|Mike Warot
|Adrianna McKinley
|-
|Gabriel Rosenhouse
|Adrianna McKinley
|-
|Malerie Kaplan
|Tim Saylor
|-
|Tucker Tomlinson
|Shawn Blaszak
|-
|Joseph Prosninitz
|Adrianna McKinley
|-
|Steve Farkas
|Adrianna McKinley
|-
|Ryan Pierce
|Adrianna McKinley
|-
|Michael Reddy
|Tim Saylor
|-
|Matt Triano
|Tim Saylor
|-
|Derek Bever
|Tim Saylor
|-
|Dan Willmott
|Tim Saylor
|-
|Tyler DeAngelo
|Tim Saylor
|-
|Michael Skilton
|Tim Saylor
|-
|Kathy Whisler
|Adrianna McKinley
|-
|Janet Dornhoff
|Matt Triano
|-
|Hilary Lee
|Matt Triano
|-
|Will Rante
|Matt Triano
|-
|Henry Behel
|Matt Triano
|-
|Alan Livshin
|Matt Triano
|-
|Michelle Garcia
|Matt Triano
|-
|Daylan Dufelmeier
|Matt Triano
|-
|Michael Maloney
|Matt Triano
|-
|Ian Cochran
|Matt Triano
|-
|Bryan Gleason
|Matt Triano
|-
|Sloan Lavery
|Matt Triano
|-
|Trey Keifer
|Matt Triano
|-
|Juan Robles
|Matt Triano
|-
|Simon Cygielski
|Matt Triano
|-
|Tom Forajter
|Matt Triano
|-
|Robert Grossman
|Matt Triano
|-
|Lucas Morris
|Matt Triano
|-
|Sergio Preston
|Matt Triano
|-
|Casey Olson
|Matt Triano
|-
|David Fell
|Ron Olson
|-
|Dubi Kaufmann
|Ron Olson
|-
|Patrick Grider
|Ron Olson
|-
|John Farmer
|Ron Olson
|-
|Sam Paris
|Ron Olson
|-
|Frances Ritchie
|Ron Olson
|-
|Ben Kern
|Ron Olson
|-
|Eric Yu
|Ron Olson
|-
|Karol Slowikowski
|Ron Olson
|-
|Chris Smith
|Ron Olson
|-
|Benjamin Miller
|Ron Olson
|-
|Laurel Garrett
|Matt Triano
|-
|Rei Kevin
|Matt Triano
|-
|Aji Slater
|Matt Triano
|-
|John Beyer
|Matt Triano
|-
|Brad Topol
|Matt Triano
|-
|-
|Shae Kurko
|Matt Triano
|-
|Hunter Koerner
|Eric Beauchamp
|-
|Kurt Ziegel
|Eric Beauchamp
|-
|Simon Pyle
|Eric Beauchamp
|-
|Connor Jansen
|Eric Beauchamp
|-
|Ananda Stevens
|Eric Beauchamp
|-
|Erik Wessing
|Eric Beauchamp
|-
|Mark Stevens
|Eric Beauchamp
|-
|Sam Paris
|Eric Beauchamp
|-
|Anthony Phelps
|Eric Beauchamp
|8/27/2015
|-
|Kyle Bieneman
|Eric Beauchamp
|8/27/2015
|-
|Jim Baker
|Eric Beauchamp
|8/27/2015
|-
|Marcin Ignasiak
|Eric Beauchamp
|-
|-
|Niko Hawley
|Eric Beauchamp
|-
|Kevin Mitchell
|Eric Beauchamp
|-
|-Caleb Young
|-Eric Beauchamp
|-
|[[User:themoffatt|Adam Moffatt]]
|Eric Beauchamp
|10/22/2015
|-
|Glenn Trussell
|Eric Beauchamp
|11/05/2015
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
}

[[Category:Shop Equipment]]
[[Category:Fabrication]]
[[Category:Woodworking]]

Rockwell Delta 20" Bandsaw

2016-01-15T21:03:54Z

Andrewd: /* List of currently authorized users */

{{Template:EquipmentPage
|owner = Pumping Station:One
|hostarea = Woodworking
|certification = yes
|hackable = no
|model = 28-350
|serial = 1457257
|arrived = 8/26/15
|where = Woodshop
|doesitwork = yes
|contact = matt . triano @ gmail . com
|value = $1,000
|image = RockwellDelta20Bandsaw.jpg
}}

'''This tool requires authorization for use. Authorizations for the 14" Rockwell do not carry over to this tool.'''

{{WoodshopProctors}}

== List of currently authorized users ==

{| class="wikitable" border="1"
! Qualified Member Keon Turner
! Trained By Ron Olson
|-
|Hunter Koerner
|Eric Beauchamp
|-
|Deanna Williams
|Eric Beauchamp
|-
|Burton Kent
|Eric Beauchamp
|-
|Casey Olson
|Jason Shanfield
|-
|Tom Judge
|Matt Triano
|-
|Jeff Smykil
|(Pending confirmation)
|-
|Anna Yu
|Matt Triano
|-
|Jon Levine
|Jason Shanfield
|-
|Kyle Bieneman
|Eric Beauchamp
|-
|Niko Hawley
|Eric Beauchamp
|-
|Kevin Mitchell
|Eric Beauchamp
|-
|Adam Moffatt
|Jason Shanfield
|-
|Peter Letscher
|Eric Beauchamp
|11/05/15
|-
|Glenn Trussell
|Eric Beauchamp
|11/05/2015
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Shine Chen
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/04/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Marcin Ignasiak
|Eric Beauchamp
|-
|Thomas Ward
|Andy L.
|11/18/2015

|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Chris Kohl
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Peter Brask
|Eric Beauchamp
|1/14/16
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
}

Dewalt Miter saw

2016-01-15T21:03:25Z

Andrewd: /* List of Currently Certified Users */

{{Template:EquipmentPage
|owner=PS:One
|model=Dewalt DW705
|arrived=April 2013
|doesitwork=yes
|contact=Michael Skilton
|where=Wood shop
|certification= yes
|hackable=no
|value=$200
|hostarea = Woodworking
|image= DeWalt miter saw.jpg}} 

{{WoodshopProctors}}

== Use ==
For miter, bevel or combination cuts in wood only.

== Specs ==
Amps 15.0 amps, No Load Speed 4,000 rpm, Blade Diameter 12 ", Arbor Size 5/8 or 1 ", 90 Degree Cross Cut Capacity (Max. Height/Resulting Width) 3-7/8 / 4-1/8 ", 90 Degree Cross Cut Capacity (Max. Width/Resulting Height) 3-7/8 / 5-7/8 ", 45 Miter Cut Capacity (Max. Height/Resulting Width) 3-7/8 / 4-1/8 ", 45 Miter Cut Capacity (Max. Width/Resulting Height) 5-1/2 / 2-1/2 ", Left 45 Degree Bevel Capacity (Max. Height/Resulting Width) 2-3/4 / 5-7/8 ", Left 45 Degree Bevel Capacity (Max. Width/Resulting Height) 7-7/8 / 1-3/4 ", Tool Weight 40.0 lbs

== Accessories ==
Crown molding stops 
Blade wrench, in a slot in the base. 
Manual

== Safety ==
This is by no means all possible safety instructions, just a few that might not have been covered at certification. 
Unplug before changing the blade, there is a shaft lock button to assist. 
For cutting wood only, inspect your piece for metal, nails,broken screws staples etc. 
Move the movable portion of the fence before adjusting for a bevel cut. 
Hold or clamp your work securely, use particular caution when cutting round or odd shaped pieces. 
Do not cut if someone is behind the saw, pieces of wood can be thrown at high velocity. 
This is most common with small cutoffs and when lifting the blade from the cut before it has stopped. 

== List of Currently Certified Users ==
As this is essentially the same as the other miter saw I transferred, with host permission, the certification list. 
Feel free to recertify if you like. 

{| class="wikitable" border="1"
! qualified member Keon Turner
! trained by Ron Olson
! date certified 10/19/15
|-
|Nathan Witt
|Danger Committee
|-
|Jeff Kantarek
|Danger Committee
|-
|David Mole
|Danger Committee
|-
|Sacha De'Angeli
|Jeff Kantarek
|-
|Joseph Fallon
|Nathan Witt
|-
|Tom Ketola
|Nathan Witt
|-
|Pete Noverini
|Matt Triano
|-
|Geoffrey Topham
|Nathan Witt
|-
|Shawn Blaszak
|Nathan Witt
|-
|James Burke
|Nathan Witt
|-
|Ryan Lanham
|Nathan Witt
|-
|Anne Petersen
|Nathan Witt
|-
|Josh Kruger
|Nathan Witt
|-
|Cory Knapp
|Jeff Kantarek
|-
|Jordan Bunker
|Nathan Witt
|-
|Constantin Gavrilescu
|Nathan Witt
|-
|Alek Shnajden
|Nathan Witt
|-
|John Dorfman
|Nathan Witt
|-
|Morgan Robertson
|Nathan Witt
|-
|Dan Locks
|Tim Saylor
|-
|Patrick Callahan
|Dan Locks
|-
|Matt Braun
|Shawn Blaszak
|-
|Bryce Lanham
|Geoffrey Topham
|-
|Joshua Rothhaus
|Shawn Blaszak
|-
|Jay Hopkins
|Shawn Blaszak
|-
|Chris Fanning
|Shawn Blaszak
|-
|Adrianna McKinley
|Danger Committee ?
|-
|Mike Warot
|Adrianna McKinley
|-
|Malerie Kaplan
|Tim Saylor
|-
|Ryan Pierce
|Internship
|-
|Kathy Whisler
|Jordan Bunker
|-
|Michael Skilton
|Tim Saylor
|-
|Michael Reddy
|Tim Saylor
|-
|Matt Triano
|Tim Saylor
|-
|Derek Bever
|Tim Saylor
|-
|Dan Willmott
|Tim Saylor
|-
|Tyler DeAngelo
|Tim Saylor
|-
| Madeleine Klichowski
| Tim Saylor
|-
| Lyn Cole
| Tim Saylor
|-
| Nathan Becka
| Tim Saylor
|-
| Brian Carstensen
| Tim Saylor
|-
| Eric Veggeberg
| Tim Saylor
|-
|Janet Dornhoff
|Matt Triano
|-
|Hilary Lee
|Matt Triano
|-
|Will Rante
|Matt Triano
|-
|Henry Behel
|Matt Triano
|-
|Alan Livshin
|Matt Triano
|-
|Michelle Garcia Matt Triano
|Matt Triano
|-
|Daylan Dufelmeier
|Matt Triano
|-
|Michael Maloney
|Matt Triano
|-
|Ian Cochran
|Matt Triano
|-
|Abhimanyu Belani
|Will Rante
|-
|Justin Miles
|Dillon Grey
|-
|Dmitry Baycharov
|Matt Triano
|-
|Stephen Ulman
|Matt Triano
|-
|Jarred Meyers
|Matt Triano
|-
|Andrew Kos
|Matt Triano
|-
|Bryan Gleason
|Matt Triano
|-
|Daniel Wells
|Matt Triano
|-
|Sean Corbett
|Matt Triano
|-
|Aaron Feigen
|Matt Triano
|-
|Bo Driscoll
|Matt Triano
|-
|Joel Shepherd
|Matt Triano
|-
|Santina Croniser
|Matt Triano
|-
|Todd Allen
|Matt Triano
|-
|Lawrence MacDevitt
|Matt Triano
|-
|Ryan Kelly
|Matt Triano
|-
|Melody Stanley
|Matt Triano
|-
|Tom Ackenhausen
|Matt Triano
|-
|JJ Schiappa
|Jason Shanfield
|-
|John Godwim
|Matt Triano
|-
|Nate Hutchins
|Matt Triano
|-
|Jeff Molek
|Matt Triano
|-
|Nathan Ellis
|Jason Shanfield
|-
|Sloan Lavery
|Matt Triano
|-
|Trey Keifer
|Matt Triano
|-
|Juan Robles
|Matt Triano
|-
|Simon Cygielski
|Matt Triano
|-
|Tom Forajter
|Matt Triano
|-
|Robert Grossman
|Matt Triano
|-
|Lucas Morris
|Matt Triano
|-
|Sergio Preston
|Matt Triano
|-
|Ron Bean
|Matt Triano
|-
|Greg Eagel
|Matt Triano
|-
|Carter Constana
|Matt Triano
|-
|Adam Glick Matt Triano
|Matt Triano
|-
|Zachary Fietsch
|Matt Triano
|-
|Solomon Hursey
|Matt Triano
|-
|Jesse Reynolds
|Matt Triano
|-
|Barmey Ung
|Matt Triano
|-
|Casey Olson
|Matt Triano
|-
|Jonathan Bisson
|Matt Triano
|-
|Bandit Gangwere
|Matt Triano
|-
|Joseph Nudell
|Matt Triano
|-
|David Butler
|Matt Triano
|-
|Kathryn Smiley
|Matt Triano
|-
|Aimee Spevak
|Matt Triano
|-
|Cassie Webster
|Matt Triano
|-
|Chris Moylan
|Matt Triano
|-
|Mike O'Connor
|Matt Triano
|-
|Tyler Hsu
|Matt Triano
|-
|Tom Judge
|Jason Shanfield
|-
|Zihe "Johnson" Luo
|Matt Triano
|-
|Giovanni Arroyo
|Matt Triano
|-
|Dan Thomson
|Jason Shanfield
|-
|Brandon Price
|Matt Triano
|-
|Arturo Duarte
|Matt Triano
|-
|Eric Braun
|Matt Triano
|-
|Jeremy Fay
|Matt Triano
|-
|Leeswann Bolden
|Matt Triano
|-
|James Porter
|Matt Triano
|-
|Jeff McBride
|Matt Triano
|-
|Connor Miller
|Matt Triano
|-
|Ashley Duca
|Matt Triano
|-
|Karen Niemczyk
|Matt Triano
|-
|Bassam Alshammari
|Matt Triano
|-
|John Fiene
|Matt Triano
|-
|Thomas Wright
|Matt Triano
|-
|Joseph Peltier
|Matt Triano
|-
|Justin Conroy Matt Triano
|Matt Triano
|-
|David Koppel
|Matt Triano
|-
|Sevin Straus
|Matt Triano
|-
|Roger Moore
|Matt Triano
|-
|Valerie Moore
|Matt Triano
|-
|Andy Schwartz
|Matt Triano
|-
|Assaf Evron
|Matt Triano
|-
|David Pelot
|Matt Triano
|-
|Rich Smith
|Matt Triano
|-
|Khoi Nguyen
|Matt Triano
|-
|Brian Keehner
|Matt Triano
|-
|Jesse Gare
|Matt Triano
|-
|Tyler Natoli
|Matt Triano
|-
|David Siegfried
|Matt Triano
|-
|Annie Zebula
|Matt Triano
|-
|Eliya Gwetta
|Matt Triano
|-
|Patrick Schliss
|Matt Triano
|-
|Arjun Wadnerkar
|Matt Triano
|-
|Sonia Yaco
|Matt Triano
|-
|Touly Phiachantharath
|Matt Triano
|-
|Matt Vibberts
|Matt Triano
|-
|Thomas Garza
|Matt Triano
|-
|Will Garza
|Matt Triano
|-
|Brennan Koziarz
|Matt Triano
|-
|Alec Weege
|Matt Triano
|-
|Eric Beauchamp
|Matt Triano
|-
|Clarence Risher
|Matt Triano
|-
|Erica Tesla
|Matt Triano
|-
|Jabu Dawdu
|Matt Triano
|-
|Karen Murphey
|Matt Triano
|-
|Matt Meshulam
|Matt Triano
|-
|Josh Myers
|Matt Triano
|-
|Weston Tanner
|Matt Triano
|-
|Hugh Sato
|Matt Triano
|-
|Nora Sluzas
|Matt Triano
|-
|Elizabeth Koprucki
|Matt Triano
|-
|Oscar Villareal
|Matt Triano
|-
|Rob Paral
|Matt Triano
|-
|Alex Schaffer
|Matt Triano
|-
|Szymon Sambor
|Matt Triano
|-
|Michael Solhelm
|Matt Triano
|-
|Rob Paral
|Michael Skilton
|-
|[[User:lucas|Lucas Goossen]]
|Matt Triano
|-
|[[User:Mwilkens|Matt Wilkens]]
|Matt Triano
|-
|Eric Slehofer
|Matt Triano
|-
|Jon Levine
|Matt Triano
|-
|Melody Snyder
|Matt Triano
|-
|Curtis Cooke
|Matt Triano
|-
|Harry Morgan
|Matt Triano
|-
|Sam Drazin
|Matt Triano
|-
|Mike Kislovsky
|Matt Triano
|-
|Keven Kalay
|Matt Triano
|-
|Kevin Pulver
|Ron Olson
|-
|Keith Hultman
|Ron Olson
|-
|Cary Lahucik
|Ron Olson
|-
|Szilvia Precsinszki
|Ron Olson
|-
|Davis Mazariegos
|Ron Olson
|-
|Mike Coriale
|Matt Triano
|-
|Dan Baltudis
|Ron Olson
|-
|David Fell
|Ron Olson
|-
|Dubi Kaufmann
|Ron Olson
|-
|Patrick Grider
|Ron Olson
|-
|Erin Kunkel
|Matt Triano
|-
|Tyler Matthew
|Matt Triano
|-
|Shae Kurko
|Matt Triano
|-
|Ben Bogler
|Matt Triano
|-
|John Farmer
|Ron Olson
|-
|Sam Paris
|Matt Triano
|-
|Chris Kleehammer
|[[User:jason|Jason Shanfield]]
|-
|Trey Elliott
|[[User:jason|Jason Shanfield]]
|-
|Nik Brink
|[[User:jason|Jason Shanfield]]
|-
|Frances Ritchie
|Ron Olson
|-
|Ben Kern
|Ron Olson
|-
|Eric Yu
|Ron Olson
|-
|Karol Slowikowski
|Ron Olson
|-
|Chris Smith
|Ron Olson
|-
|Benjamin Miller
|Ron Olson
|-
|[[User:anthony|Anthony Sontag]]
|Justin Conroy
|-
|Bradley Topol
|Matt Triano
|-
|Eugene Liokumovich
|Ron Olson
|-
|Laurel Garrett
|Matt Triano
|-
|Rei Kevin
|Matt Triano
|-
|Aji Slater
|Matt Triano
|-
|John Beyer
|Matt Triano
|-
|[[User:papaben44|Benjamin Dambman]]
|Matt Triano
|4/14/2015
|-
|Tomas Ward
|Ron Olson
|4/26/2015
|-
|Les Schier
|Jason Shanfield
|5/2/15
|-
|Mike Jones
|Matt Triano
|5/28/15
|-
|Hunter Koerner
|Eric Beauchamp
|6/4/15
|-
|Kurt Ziegel
|Eric Beauchamp
|-
|Simon Pyle
|Eric Beauchamp
|6/4/15
|-
|Andy Richardson
|Matt Triano
|4/14/15
|-
|Connor Jansen
|Eric Beauchamp
|6/4/15
|-
|Ryan Neuman
|Ron Olson
|-
|Erik Wessing
|Eric Beauchamp
|-
|Ananda Stevens
|Eric Beauchamp
|7/18/15
|-
|Mark Stevens
|Eric Beauchamp
|7/18/15
|-
|Anthony Phelps
|Eric Beauchamp
|8/27/2015
|-
|Jim Baker
|Eric Beauchamp
|8/27/2015
|-
|Kyle Bieneman
|Ron Olson
|-
|Marcin Ignasiak
|Eric Beauchamp
|-
|Deanna Williams
|Eric Beauchamp
|-
|Glenn Powers
|Matt Triano
|3/2015
|-
|Niko Hawley
|Eric Beauchamp
|-
|Kevin Mitchell
|Eric Beauchamp
|-
|-Caleb Young
|-Eric Beauchamp
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Shine Chen
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Chris Kohl
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Peter Brask
|Eric Beauchamp
|1/14/16
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
}

[[Category:Shop Equipment]]
[[Category:Fabrication]]
[[Category:Woodworking]]

SawStop table saw

2016-01-15T21:02:46Z

Andrewd: /* List of Currently Certified Users */

{{Template:EquipmentPage
|owner = PS:One
|certification=yes
|hackable = NO
|model = 3.0HP 220V
|serial = NA
|arrived = 9/1/2012
|doesitwork = yes
|contact = Matt Triano
|where = Woodshop
|value = $3,000.00
|image = SawStop.jpg
|hostarea = Woodworking
}}
[[File:Saw stop badge.jpg|thumb|right|200px]]

= Authorization for this tool by authorized proctors only =
== Authorized Proctors ==
{| class="wikitable" border="1"
|-
|Matt Triano
|-
|Jason Shanfield
|-
|Ron Olson
|-
|Eric Beauchamp
|-
|}

== Status ==

Repaired and in working order as of 11/9/2015

== How to Become an Authorized Proctor ==

Contact area host Matt Triano.

= Rules =
# Do not move the machine ever.
# Never use the table as a work surface.
# Always have the dust collection on. Turn it on before you plug in the saw and off after you unplug the saw.
# Always check your material on the blade before you spin up the blade. If the light turns red, DO NOT CUT.
# Always check your wood for nails or staples. If you're not sure, check the entire piece with a magnet.
# If you break something, or damage the saw, contact the area host immediately. Don't let others do more damage or hurt themselves by using a broken tool.
# Always dust the entire machine when you are done. Also check the motor compartment after every use and vacuum out as needed.

= Additional Information =

== Blade Brake ==
This saw is equipped with a safety feature that will (hopefully) stop the blade when it contacts something conductive-- like your hand. However, that means you normally can't cut conductive things with this saw or you will trigger the safety brake. This is good if it was your hand in the way, but it also destroys the sawblade and requires installation of a replacement part that costs $70+ every time. And the saw will be down until the replacement can be installed.

According to the owner's manual: "Conductive materials such as aluminum and other metals, carbon fiber materials, '''mirrored acrylic''', carbon-filled materials, etc. will typically '''cause the brake to activate'''." [Emphasis added.]

Other things that may trigger the brake include wet wood, and wood with embedded nails or staples. Lexan and green pressure-treated wood reportedly can also be a problem. That is why the rules instruct you to check your material on the side of the blade before spinning it up, and to check your wood for nails or staples!

== Notes ==
* There's an m8 hole drilled and tapped in the mitre gauge. The post from a magnetic base of our dial indicators thread in. The post may require a spacer so the threads don't stick out (use a stack of washers or a larger-than-m8 nut).
* The right hand table adjusting screw was bent while aligning the table. The table was aligned without it. Aligning the arbor tilt axis will be *really tough* without a replacement. (Part #11 in the cabinet and table exploded diagram in the manual p98)
* The rear rip fence rail has places to put 4 countersunk allen bolts. The left hand bolt screwed into the main table was too long and made contact with an internal table part (probably the rear trunion). It probably pushed the table out of alignment and caused binding while re-aligning the table. That bolt was left out. Don't replace it!

== Training Links ==
* [http://www.sawstop.com/images/uploads/manuals/PCS%20Owners%20Manual%20Model%20PCS31230%20V5.0%2009-13.pdf Owner's Manual]
* [http://web.archive.org/web/20130224091815/http://www.woodworkersjournal.com/Main/Articles/Table_Saw_Maintenance_Skill_Builder_Power_Tool_Tun_8197.aspx Table Saw Maintenance]

= List of Currently Certified Users =
{| class="wikitable" border="1"
! Qualified Member Keon Turner
! Trained By Ron Olson
! Date Certified
|-
|Shawn Blaszak
|Danger Committee
|-
|[[User:Meistertek|Dan Meyer]]
|Sean Blaszak
|-
|Jacob Ginsburg
|Shawn Blaszak
|-
|Eric Stein
|Steve Finkelman / Danger Committee
|-
|[[User:Dee|Dee Newcum]]
|Shawn Blaszak
|-
|Ryan Pierce
|Shawn Blaszak
|-
|Tucker Tomlinson
|Shawn Blaszak
|-
|Adrianna McKinley
|Danger Committee
|-
|Anthony Barker
|Adrianna McKinley
|-
|Avner Shanan
|Adrianna McKinley
|-
|Colin Parsons
|Adrianna McKinley
|-
|Dan Denby
|Adrianna McKinley
|-
|Dillon Gray
|Adrianna McKinley
|-
|Douglas Savitsky
|Adrianna McKinley
|-
|Hailey Willis
|Adrianna McKinley
|-
|Jeremy Bloyd-Peshkin
|Adrianna McKinley
|-
|Jeremy Kay
|Adrianna McKinley
|-
|Jessica Cobb
|Adrianna McKinley
|-
|Jordan Bunker
|Adrianna McKinley
|-
|Kori Rays
|Adrianna McKinley
|-
|Patrick Callahan
|Adrianna McKinley
|-
|Ryan Brandys
|Adrianna McKinley
|-
|Shawn Blaszak
|Adrianna McKinley
|-
|Steve Farkas
|Adrianna McKinley
|-
|Steve Finkleman
|Adrianna McKinley
|-
|Mike Warot
|Adrianna McKinley
|-
|Eric Stein/Toba
|Adrianna McKinley
|-
|Ryan Pierce
|Adrianna McKinley
|-
|Geoffrey Topham
|Adrianna McKinley
|-
|Tim Saylor
|Ryan Pierce
|-
|Hailey Willis
|Tim Saylor
|-
|James Longfield
|Tim Saylor
|-
|Liam Tuohy
|Tim Saylor
|-
|Jim Tuohy
|Tim Saylor
|-
|Sean Nixon
|Tim Saylor
|-
|Michael Reddy
|Tim Saylor
|-
|Matt Triano
|Tim Saylor
|-
|Derek Bever
|Tim Saylor
|-
|Dan Willmott
|Tim Saylor
|-
|Tyler DeAngelo
|Tim Saylor
|-
| Michael Skilton
| Adrianna McKinley
|-
| Dean Anderson
| Tim Saylor
|-
|Kathy Whisler
|Tucker Tomlinson
|-
| João Santos
| Geoffrey Topham
|-
|David Fell
|Tucker Tomlinson
|-
|[[User:Bikemandan|Dan Locks]]
|Adrianna McKinley
|-
|Dave Earley
|[[User:Bikemandan|Dan Locks]]
|-
| Boban Nikolic
| Michael Skilton
|-
| Madeleine Klichowski
| Tim Saylor
|-
| Lyn Cole
| Tim Saylor
|-
| Nathan Becka
| Tim Saylor
|-
| Brian Carstensen
| Tim Saylor
|-
| Eric Veggeberg
| Tim Saylor
|-
| George Shaw
| Tim Saylor
|-
|Janet Dornhoff
|Matt Triano
|-
|Hilary Lee
|Matt Triano
|-
|Will Rante
|Matt Triano
|-
|Henry Behel
|Matt Triano
|-
|Alan Livshin
|Matt Triano
|-
|Michelle Garcia
|Matt Triano
|-
|Daylan Dufelmeier
|Matt Triano
|-
|Michael Maloney
|Matt Triano
|-
|Ian Cochran
|Matt Triano
|-
|Abhimanyu Belani
|Will Rante
|-
|Justin Miles
|Adrianna McKinley
|-
|Dmitry Baycharov
|Matt Triano
|-
|Stephen Ulman
|Matt Triano
|-
|Jarred Meyers
|Matt Triano
|-
|Andrew Kos
|Matt Triano
|-
|Bryan Gleason
|Matt Triano
|-
|Jason Sharfield
|Matt Triano
|-
|Dave Schact
|Matt Triano
|-
|Daniel Wells
|Matt Triano
|-
|Sean Corbett
|Matt Triano
|-
|Aaron Feigen
|Matt Triano
|-
|Bo Driscoll
|Matt Triano
|-
|Joel Shepherd
|Matt Triano
|-
|Santina Croniser
|Matt Triano
|-
|Todd Allen
|Matt Triano
|-
|Lawrence MacDevitt
|Matt Triano
|-
|Ryan Kelly
|Matt Triano
|-
|Melody Stanley
|Matt Triano
|-
|Tom Ackenhausen
|Matt Triano
|-
|JJ Sciappa
|Jason Shanfield
|-
|Jason Araujo
|Derek Bever
|-
|John Godwim
|Matt Triano
|-
|Jeff Molek
|Matt Triano
|-
|Nathan Ellis
|Jason Shanfield
|-
|Sloan Lavery
|Matt Triano
|-
|Trey Keifer
|Matt Triano
|-
|Juan Robles
|Matt Triano
|-
|Simon Cygielski
|Matt Triano
|-
|Tom Forajter
|Matt Triano
|-
|Robert Grossman
|Matt Triano
|-
|Lucas Morris
|Matt Triano
|-
|Sergio Preston
|Matt Triano
|-
|Ron Bean
|Matt Triano
|-
|Greg Eagel
|Matt Triano
|-
|Carter Constana
|Matt Triano
|-
|Adam Glick
|Matt Triano
|-
|Zachary Fietsch
|Matt Triano
|-
|Solomon Hursey
|Matt Triano
|-
|Jesse Reynolds
|Matt Triano
|-
|Eduard Shlahtichman
|Matt Triano
|-
|Skittles Rainbow
|Matt Triano
|-
|Tom Jurgensen
|Matt Triano
|-
|Barmey Ung
|Matt Triano
|-
|Casey Olson
|Matt Triano
|-
|Jonathan Bisson
|Matt Triano
|-
|Ed Bennett
|Matt Triano
|-
|Anna Yu
|Matt Triano
|-
|Bandit Gangwere
|Matt Triano
|-
|Joseph Nudell
|Matt Triano
|-
|David Butler
|Matt Triano
|-
|Kathryn Smiley
|Matt Triano
|-
|Aimee Spevak
|Matt Triano
|-
|Cassie Webster
|Matt Triano
|-
|Chris Moylan
|Matt Triano
|-
|Mike O'Connor
|Matt Triano
|-
|Tyler Hsu
|Matt Triano
|-
|Zihe "Johnson" Luo
|Matt Triano
|-
|Giovanni Arroyo
|Matt Triano
|-
|Ian McLeod
|Derek Bever
|-
|Dan Thomson
|Jason Shanfield
|-
|Brandon Price
|Matt Triano
|-
|Arturo Duarte
|Matt Triano
|-
|Eric Braun
|Matt Triano
|-
|Jeremy Fay
|Matt Triano
|-
|Leeswann Bolden
|Matt Triano
|-
|James Porter
|Matt Triano
|-
|Jeff McBride
|Matt Triano
|-
|Connor Miller
|Matt Triano
|-
|Ashley Duca
|Matt Triano
|-
|Karen Niemczyk
|Matt Triano
|-
|Bassam Alshammari
|Matt Triano
|-
|John Fiene
|Matt Triano
|-
|Thomas Wright
|Matt Triano
|-
|Tom Judge
|Jason Shanfield
|-
|Joseph Peltier
|Matt Triano
|-
|Justin Conroy
|Matt Triano
|-
|David Koppel
|Matt Triano
|-
|Sevin Straus
|Matt Triano
|-
|Roger Moore
|Matt Triano
|-
|Valerie Moore
|Matt Triano
|-
|Andy Schwartz
|Matt Triano
|-
|Assaf Evron
|Matt Triano
|-
|David Pelot
|Matt Triano
|-
|Rich Smith
|Matt Triano
|-
|Khoi Nguyen
|Matt Triano
|-
|Brian Keehner
|Matt Triano
|-
|Jesse Gare
|Matt Triano
|-
|Tyler Natoli
|Matt Triano
|-
|David Siegfried
|Matt Triano
|-
|Annie Zebula
|Matt Triano
|-
|<strike>Eliya Gwetta</strike>
|Matt Triano
|-
|Patrick Schliss
|Matt Triano
|-
|Arjun Wadnerkar
|Matt Triano
|-
|Alec Weege
|Matt Triano
|-
|Sonia Yaco
|Matt Triano
|-
|Tom Bossier
|Jason Shanfield
|-
|Ray Doeksen
|Jason Shanfield
|-
|Touly Phiachantharath
|Matt Triano
|-
|Matt Vibberts
|Matt Triano
|-
|Thomas Garza
|Matt Triano
|-
|Will Garza
|Matt Triano
|-
|Brennan Koziarz
|Matt Triano
|-
|Eric Beauchamp
|Matt Triano
|-
|Clarence Risher
|Matt Triano
|-
|Erica Tesla
|Matt Triano
|-
|Jabu Dawdu
|Matt Triano
|-
|Karen Murphey
|Matt Triano
|-
|Matt Meshulam
|Matt Triano
|-
|Josh Myers
|Matt Triano
|-
|Weston Tanner
|Matt Triano
|-
|Hugh Sato
|Matt Triano
|-
|Nora Sluzas
|Matt Triano
|-
|Elizabeth Koprucki
|Matt Triano
|-
|Oscar Villareal
|Matt Triano
|-
|Rob Paral
|Matt Triano
|-
|Alex Schaffer
|Matt Triano
|-
|Szymon Sambor
|Matt Triano
|-
|Michael Solhelm
|Matt Triano
|-
| Rob Paral
| Michael Skilton
|-
| Sonia Yaco
| Matt Triano
|-
| Alyssa Moxley
| Ron Olson
|-
| Kyle Bieneman
| Ron Olson
|-
|Steve Ioannou
|Matt Triano
|-
|[[User:Mwilkens|Matt Wilkens]]
|Matt Triano
|-
|Eric Slehofer
|Matt Triano
|-
|Jon Levine
|Matt Triano
|-
|Melody Snyder
|Matt Triano
|-
|Curtis Cooke
|Matt Triano
|-
|Harry Morgan
|Matt Triano
|-
|Lucas Goossen
|Matt Triano
|-
|Sam Drazin
|Matt Triano
|-
|Mike Kislovsky
|Matt Triano
|-
|Keven Kalay
|Matt Triano
|-
|Jacob Rush
|Ron Olson
|-
|Sam Reicks
|Ron Olson
|-
|Kevin Pulver
|Ron Olson
|-
|Keith Hultman
|Ron Olson
|-
|Cary Lahucik
|Ron Olson
|-
|John Keippel
|Ron Olson
|-
|Mario Rodriguez
|Ron Olson
|-
|Szilvia Precsinszki
|Ron Olson
|-
|Davis Mazariegos
|Ron Olson
|-
|Pete Noverini
|Matt Triano
|-
|Mike Coriale
|Matt Triano
|-
|Dan Baltudis
|Ron Olson
|-
|Viktor Bazarov
|Ron Olson
|-
|Roman Solomatov
|Ron Olson
|-
|Patrick Grider
|Ron Olson
|-
|Dubi Kaufmann
|Ron Olson
|-
|Erin Kunkel
|Matt Triano
|-
|Tyler Matthew
|Matt Triano
|-
|Shae Kurko
|Matt Triano
|-
|Ben Bogler
|Matt Triano
|-
|Rod McLah
|Ron Olson
|-
|Andrew Dreasler
|Ron Olson
|-
|Sam Paris
|Matt Triano
|-
|Chris Kleehammer
|[[User:jason|Jason Shanfield]]
|-
|Trey Elliott
|[[User:jason|Jason Shanfield]]
|-
|Nik Brink
|[[User:jason|Jason Shanfield]]
|-
|Frances Ritchie
|Ron Olson
|-
|Ben Kern
|Ron Olson
|-
|Knute Martell
|Ron Olson
|-
|Eric Yu
|Ron Olson
|-
|Knute Martell
|Ron Olson
|-
|Bob McGrath
|Ron Olson
|-
|Karol Slowikowski
|Ron Olson
|-
|Michelle Deleon
|Ron Olson
|-
|Chris Smith
|Ron Olson
|-
|Benjamin Miller
|Ron Olson
|-
|Jennie P
|Ron Olson
|-
|Joe Wallace
|Ron Olson
|-
|Eugene Liokumovich
|Ron Olson
|-
|Laurel Garrett
|Matt Triano
|-
|Rei Kevin
|Matt Triano
|-
|Aji Slater
|Matt Triano
|-
|John Beyer
|Matt Triano
|-
|Jay Kasturi
|Ron Olson
|-
|Ryan Neuman
|Ron Olson
|-
|[[User:papaben44|Benjamin Dambman]]
|Matt Triano
|4/14/2015
|-
|Tomas Ward
|Ron Olson
|4/26/2015
|-
|Les Schier
|Jason Shanfield
|5/2/15
|-
|Mike Jones
|Matt Triano
|5/12/15
|-
|Hunter Koerner
|Eric Beauchamp
|6/4/15
|-
|Kurt Ziegel
|Eric Beauchamp
|6/4/15
|-
|Simon Pyle
|Eric Beauchamp
|6/4/15
|-
|Andy Richardson
|Matt Triano
|4/14/15
|-
|Connor Jansen
|Eric Beauchamp
|6/4/15
|-
|Raj Perera
|Matt Triano
|-
|Matt Crump
|Jason Shanfield
|7/1/15
|-
|Erik Wessing
|Eric Beauchamp
|-
|Ananda Stevens
|Eric Beauchamp
|7/18/15
|-
|Mark Stevens
|Eric Beauchamp
|7/18/15
|-
|Anthony Phelps
|Eric Beauchamp
|8/27/2015
|-
|Jim Baker
|Eric Beauchamp
|8/27/2015
|-
|Ralph Brendler
|Eric Beauchamp
|8/27/2015
|-
|Bruce McConachie
|Eric Beauchamp
|8/27/2015
|-
|Shane Kanter
|Ron Olson
|9/10/2015
|-
|Burton Kent
|Ron Olson
|9/10/2015
|-
|Marcin Ignasiak
|Eric Beauchamp
|-
|Deanna Williams
|Eric Beauchamp
|-
|Jeff Smykil
|Matt Triano
|9/26/2015
|-
|Glenn Powers
|Matt Triano
|3/2015
|-
|Niko Hawley
|Eric Beauchamp
|-
|Kevin Mitchell
|Eric Beauchamp
|-
|John McDonald
|Eric Beauchamp
|10/05/2015
|-
|[[User:themoffatt|Adam Moffatt]]
|Eric Beauchamp
|10/22/2015
|-
|Jean Michel Crettaz
|Eric Beauchamp
|10/22/2015
|-
|Mike Mandrea
|Eric Beauchamp
|11/05/2015
|-
|-Caleb Young
|-Eric Beauchamp
|-
|Peter Letscher
|Eric Beauchamp
|11/05/15
|-
|Glenn Trussell
|Eric Beauchamp
|11/05/2015
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Shine Chen
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/04/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Chris Kohl
|Eric Beauchamp
|1/8/2016
|-
|Peter Brask
|Eric Beauchamp
|1/14/16
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
}

[[Category:Shop Equipment]]
[[Category:Fabrication]]
[[Category:Woodworking]]
[[Category:Certification Clarification Needed]]