PS:1 Wiki Dev - User contributions [en]

Lincoln Electric 3200HD

2017-05-06T22:50:24Z

Pedrosk: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = Pumping Station One
|certification = yes
|hackable = no
|model = Weld Pak 3200HD
|arrived = 2015-04-27
|doesitwork = yes
|where = Hot Metals
|value = $340
|contact = Ron Olson
|image = IMG_1583.JPG
|hostarea = Hot Metals
}}

Essentially "a hot melt glue gun for metals". It releases 75% argon / 25% CO2 gas as you weld to prevent oxidation of the metal. You're melting the metals you're joining, and adding a bead as well.

== Safety ==
* Wear natural fibers (cotton, wool) only. It puts out sparks and can melt synthetics onto your skin.
* Wear closed-toe shoes, unless you like setting your feet on fire.
* Cover all skin - it puts out a lot of UV light. You'll get a sunburn, guaranteed. Plus, you can get burned.
* It's a good idea to have a hat or something under the face shield, as sparks will go onto the top of your head.
* There are two screens on wheels - arrange them to block UV light from going to the rest of the shop.
* Use the thick gloves, also the face shield. The face shield for MIG is pretty handy, it darkens when you start welding.
* Yell "welding" before starting so anyone sneaking up on you is aware to avert their eyes.
* The piece will be hot for a long time after you welded it. You can grab it with tongs and dip in buckets.

== Approximate Steps for Use ==

=== Preparation ===
# Pull out the machine
# Clean out welding tip with the pliers that have files on the outside of the jaws.
# Check inside if it's wired for MIG. There's a diagram on the inside of the case. This should not change but can.
## The reel of metal wire size should match your recommended diameter.
## Wire adjustment is much like the 3D printers' - it flips up and has a tension holder
# Also check the recommended settings for welding. You will need to know a letter and a number.
# Set the recommended settings on the front panel.
# Plug it in.
# Cut the wire tip using the pliers to the recommended length.
# Check that the gas pressure is above 500PSI. If it's below, press the button on the left wall that will tell Ron to order more gas.
## Not sure if can use below 500PSI - I think we're fine as long as it outputs 20CFH?
# Adjust gas output on machine to 20CFH
# Attach the ground to either the table or the part, depending on what you're doing.

=== Use ===
* Close the screens behind you.
* Check around periodically for stuff you set on fire. This thing puts out hot sparks. I set a rag on fire the first time I used it. I was confused why the authorizer had brought a smoldering rag for authorization - nope, that was me.
* You may want to brush the joints before welding. Be sure to pay attention to the labeling on the metal brush - steel only.
* It may be a good idea to tack both ends of the parts being welded.
* Make sure there's no crimps in the tube feeding the metal wire. It should be as straight as possible.
* Ideally you would weld at about a 45° angle.
* If welding something perpendicular, you're trying to make a puddle (bead) that equally touches both parts. You'll angle it towards the top piece slightly more.
* Yell "Welding" before starting.
* The machine has a duty cycle of 2 minutes for every 10. That means you can only use the machine for 2 minutes before taking a break to let it cool down. In practice you usually won't have a problem with this, but for longer, and multiple welds, pay attention to this.

=== When Done ===
# Turn off gas.
# Pull trigger til the PSI reaches 0.
# Nice to cut off the extra wire you just fed in the above step.
# Unplug.
# Coil up everything and put back.
# Brush off the mess from the table like the fine, upstanding citizen you are.
# Put away anything else you got out, like metals, gloves, face mask.

== Status ==

Standard electric power plug has been replaced with a NEMA 5-20 type plug, plugs right into the wall socket there but won't plug into a power strip or extension cord.

== Some Info ==
http://www.4x4review.com/lincoln-eletrics-weld-pak-3200-hd-mig-welder/
== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Authorized Member Keon Turner
! Authorized By
|-
|Alejandro Drexler
|Ron Olson
|-
|Chris Agocs
|Ron Olson
|-
|Yousef Zaffarkhan
|Ron Olson
|-
|Andy Larkin
|Ron Olson
|-
|Samuel Sion
|Ron Olson
|-
|Lauren Svedman
|Ron Olson
|-
|Aaron Carlock
|Ron Olson
|-
|Greg Kudlacz
|Ron Olson
|-
|Daniel Maziarz
|Ron Olson
|-
|Connor Sullivan
|Tom Judge
|-
|Keith Couture
|Ron Olson
|-
|Jordan Montes
|Ron Olson
|-
|Ken Burkhardt
|Ron Olson
|-
|Sam Olendorf
|Ron Olson
|-
|Eugene Liokumovich
|Ron Olson
|-
|[[user:mkeith|Matt Keith]]
|Ron Olson
|-
|[[user:panchan99|Juan Ramos]]
|Jeremy Bloyd-Peshkin
|-
|[[user:smash|Ashley Matrisciano]]
|Jeremy Bloyd-Peshkin
|-
|[[user:smash|Burton Kent]]
|Jeremy Bloyd-Peshkin
|-
|Brian Cuocci
|Ron Olson
|-
|Sam Paris
|Ron Olson
|-
|Clarence Bartenhagen
|Chris Iacullo
|-
|[[user:Pedrosk|Ed Breuer]]
|Chris Iacullo
|Feb 2017
|}

[[Category: Hot Metals]]

Shopbot PRS CNC router

2017-05-01T18:57:09Z

Pedrosk: /* Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|serial = TBD.
|certification = yes
|hackable = no
|model = Shopbot PRS #10108 96-48
|arrived = 2014
|image = Shopbot.jpg
|doesitwork = yes
|contact = [[CNC|CNC Area Host]]
|where = TBD
|value = $16000
|hostarea = CNC
}}
= Shopbot PRS #10108 96-48 =
http://www.shopbottools.com/mProducts/prSstandard.htm
Nominal Cutting Area 96"x 48"x 6" (2.44m x 1.22m x .15m)
Total Movement Area 102" x 50" x 8" (2.59m x 1.27m x .20m)

=Status history=
12/27/16 - Fixed Shopbot x-axis homing. The cable had been pulled on hard enough that some of the conductors broke inside the cable. It has been spliced, soldered, and heatshrinked back together.

= Authorization for this tool by authorized proctors only =

What this means: this means you cannot get authorized by just anyone who is already authorized. You can only get authorized by a few people, the proctors listed below.

Authorization sessions are scheduled roughly monthly. Check the [https://www.meetup.com/Pumping-Station-One/events/ Meetup calendar] for upcoming authorizations. If no ShopBot sessions are currently scheduled, ask on the [https://groups.google.com/group/pumping-station-one/ Google Group].

Be aware that this authorization consists of two parts; the first session is a classroom session that will cover the software required and introduce you to the essential settings and chip-load calculation, and the second part, scheduled separately, is a hands-on class.

== Authorized Proctors ==
{| class="wikitable" border="1"
|-
|Elizabeth Koprucki
|Danger Committee
|-
|Bart Dring
|Danger Committee
|-
|Ryan Pierce
|Danger Committee
|-
|Nathan Ellis
|Danger Committee
|-
|Michael Skilton
|Danger Committee
|-
|Khoi Nguyen
|Michael Skilton
|-
|Andrew Camardella
|Elizabeth Koprucki
|-
|Matt Meshulam
|Andrew Camardella
|-
|}

== How to Become an Authorized Proctor ==
Get an ok from the area host. Successfully run an authorization supervised by an authorized proctor.
It's recommended that initial authorizations be limited to 2 or less.

= Documentation =

[[File:Shopbotassembly.pdf|Shopbotassembly.pdf]]

[[File:Squaringshopbot.pdf|Squaring the ShopBot]]

[[File:Programming_handbook.pdf|Programming Handbook]]

[[File:PRS Maintenance Schedule.pdf|Maintenance Schedule]]

[[File:ShopBot_USB_Connection_Troubleshoot.pdf]] - USB Troubleshooting Guide

[[File:ShopBot_Tech_Support_FAQ_2016_09_12.pdf]] - Tech Support FAQ

[[File:SBG00142 User Guide 2013 05 01.pdf|SBG00142 User Guide 2013 05 01.pdf]] - User Guide

[[File:B17P.763_Schematic.pdf]] - Omer Nail Gun Documentation

[http://www.shopbottools.com/ShopBotDocs/files/quick%20start%20guide%202013%2007%2023.pdf QuickStart]

X, Y, Z probe: https://pumpingstationone.org/2015/09/xyz-finder-for-the-shopbot/

[http://drshopbot.com/index.php?title=Main_Page "Dr Shopbot" wiki]

[http://drshopbot.com/index.php?title=MaintainingConnection "Maintaining Connections"]

= Tutorials =
[https://www.youtube.com/watch?v=xWCZfYHOYWw Part 1 of our Shopbot Authorization] - This is available as a refresher only. You still need to go to the class when it happens to get access to the hands-on Part 2.

[http://www.woodguide.org/files/2014/07/CNCrouter_bit_basics.pdf Router Bit Basics for CNC - VERY USEFUL]

[https://groups.google.com/forum/?fromgroups=#!searchin/pumping-station-one/shopbot Shopbot Threads on Member List]

[https://groups.google.com/forum/?fromgroups=#!searchin/pumping-station-one/shopbot Shopbot Forum]

[https://groups.google.com/d/msg/pumping-station-one/vUF3iKRQ9yc/_qNnLXzZ3QcJ Overview of Cut Load calcualtions for setting bit feed and speed rates]

== Software Tool Chain ==
*Illustrator
*Inkscape
*Vectric Aspire
**Allows for 2D and 3D linework and toolpath creation
**Only available on the Shapeoko Computer
*Vectric V-Carve Makerspace Edition
**Allows for 2D linework and toolpath creation
**Allows at home use of V-Carve - output only at PS1
**Our Makerspace Code is: E4793-F6472-BB9E5-9B114-3FEEB-73649-16F4F
*Autodesk Fusion 360
**The ShopBot computer does not have this and may not be fast enough to run it.
**You '''MUST''' use the custom post-processor below. Otherwise, you will bypass the safety check to make sure the spindle really is running!
**For local '''Windows''', to install this on your local computer:
***Unzip and install this in C:\Users\YourName\AppData\Roaming\Autodesk\Fusion 360 CAM\Posts
***Note that AppData is often a hidden folder!
***Inside Fusion 360, when you select Actions / Post Process, under Configuration Folder, hit Setup and select Use Personal Posts.
**For local '''Mac'''
*** Unzip and install in Macintosh HD> Users> USERNAME> Autodesk> Fusion 360 CAM> Posts
*** In Fusion 360, when you select Actions > Post Process, under Settings select Personal Posts for the Source
**For '''Cloud'''
*** Open Fusion 360 and navigate to Libraries > Assets in the Data Panel.
*** Double click the Assets > CAMPosts folder to enter it.
*** Use the Upload button to upload the desired post processor from your local machine to the Assets > CAMPosts folder. This will upload the post to the cloud and allow you to access it anywhere you may login to your Fusion 360 account through My Cloud Posts.
*** After enabling cloud libraries in Fusion 360, you will be able to access your cloud post processor library by setting the Configuration Folder (Windows) or Source (Mac) to My Cloud Posts. Both of these dialog boxes are shown below. You will then be able to select the Cloud post you uploaded in the Post Configuration field (Windows) or the Post Processor field (Mac).
====Chip Load Calculation====
*[http://www.pdsspindles.com/engineering-speeds Bit Parameter Overview by PDS Spindles]
*[http://www.monstertool.com/monster_tool_calculators.html Monster Tools Chip Load Calculator]
*[http://www.pdsspindles.com/admin/modules/page_editor/uploads/image/Chip%20load%20for%20common%20tool%20diameters%20(Inches).jpg Chip Load Chart by PDS Spindles]
*[https://groups.google.com/forum/#!searchin/pumping-station-one/makerspace$20edition/pumping-station-one/cTwfUHxESjU/7m_lI8UWCgAJ How to install Makerspace Version]

== User Tips & Troubleshooting Reports ==
[http://www.sgstool.com/PDF-speedfeeds/SGS-Speeds-Feeds-GP.pdf Some feed and speed recommendations for small bits]

Add your experiences with feeds and speeds or other tips here:
[[Shopbot_User_Tips]]

Add troubleshooting reports here:
[[Shopbot_Troubleshooting_Reports]]

=== Materials ===

* [[Shopbot_PRS_CNC_router/Aluminium|Aluminium]]
* [[Shopbot_PRS_CNC_router/Brass|Brass]]
* [[Shopbot_PRS_CNC_router/Wood|Wood]]

== Authorization Checklist ==

This is here as a checklist for proctors to follow when authorizing people. It can also help remind you of things after you are authorized. Just reading this does not authorizing you.

* How to get authorized
** Watch [http://www.meetup.com/Pumping-Station-One/ the meetup group] for a recurring class on the second Thursday and last Sunday of the month. Sometimes check [https://groups.google.com/forum/#!forum/pumping-station-one the forum] for announcements or ask on the forum if no announcements have been made for a few weeks.

* Authorization group size
** There is no cap to the software instruction preceding the machine usage portion of the class. If you come to this portion it is easier to get fully authorized at a later date.
** 3 machine users - each person will run a job (~1/2 hr each) and everyone will assist each other in completing a job profile and pocket cut. You must be present for the entire authorization

* Safety
** Safety Glasses
** Hearing Protection
** Dust Protection

* What can go wrong (and what to do)

* How does machine work
** Axes
** Motors
** Spindle

* Daily Maintenance
** Spindle bearing warm up.
*** The "C5" warm up routine should be run on the first job of the day. It runs the spindle at 3 speeds for 3 minutes each to warm up the bearings. (When it doubt, warm it up)

* Extended Maintenance
** See maintenance schedule file under documentation.
** Grease the racks
** Use Grease type: Manual states any type is safe there is some in the draw

* Machine Control
** Turn on sequence
*** Log into computer
*** Turn on Shopbot big red and yellow twist switch (see zeroing below)
*** Insert Key and turn to "engaged" position.
*** The VDF should light up, the spindle fan should be on.
*** Start "Shopbot 3" program.
*** Open Tools...Spindle RPM Control menu (to allow RPM control)
**** Make sure collet is tightened or no tool or nut is installed
**** Run the C5 warm up routine
** Jogging
*** Keypad
*** Arrow Keys + Page Up, Page Down (ctrl for fast jog)

* CAM Software
** Vectric V Carve
** Just the basics...separate class for advanced V Carve.
** Online videos

* Running your Job
** Zeroing X & Y
*** With machine off slow push gantry towards X0 until it hits hard stops (optional)
*** Turn on big red switch while still holding gantry.
*** Jog machine away from X0 Y0 so machine will find switches
*** Click X, Y zero button.
** Zeroing Z (top of work piece)
*** Jog over your work piece
*** Place Z zero plate on work piece under the bit
*** Place clip on bit
*** Test connection by touching plate to bit and watch for light #1 to light
*** Click the Z 0 button (it will touch off twice!!!)
*** If Z is critical, you may want to verify that your bit has been zeroed properly by using a "MZ,0" command over the surface you have zeroed the bit to. Repeat zeroing if not correct.

* Waste Board and clamping

* Collets, Bits, Feeds and Speeds
** Feeds and Speeds
*** Use a Cut Load Calculator to determine which feeds and speeds you should be using for your specific bits. An overview is avaialble at: [https://groups.google.com/d/msg/pumping-station-one/vUF3iKRQ9yc/_qNnLXzZ3QcJ]
** Collets
*** We currently have collets for 1/2, 1/4, 3/16 and 1/8" shank bits.
*** Try to keep them clean and store them away from dust between uses. Dust between the gaps will produce runout. The drawer mounted under the Shopbot is the right place to store these items.
*** If the collet nuts are not threading smoothly try cleaning the threads with a small brush, spindle threads as well.
** Bits
*** Use bits designed for the material you are cutting. Don't just steal a bits from the Bridgeport. They won't do a good job and will probably overheat.
*** For cutting out things, use the smallest appropriate bit. Using a 1/2" bit to cutout will just create a lot of mess.

* ShopBot should not be used for...
** Metals other than aluminum
** Cutting anything that requires coolant or lubricant (it will ruin the waste board)
** Ripping lumber (use the table saw)
** Thickness Planning (Use the planner if you can)
** Drilling holes with drill bits (a small end mill works better)

* How to leave the machine (be excellent)
** Machine
*** Home the machine to X0, Y0
*** Turn off both switches
*** Remove Key
*** Remove bit and collet.
*** Place both collet wrenches on top of electronics box
*** clean up work area
*** Smooth out waste board if you puckered it at all.
*** Check if the dust collector needs to be emptied

** Post a picture on our [[Blog]] please!

== Pre-Flight Checklist ==
* Did you home the machine?
* Is the dust collect gate open?
* Are you sure you have the right X, Y orientation for your file and material?
* Did you set the proper X,Y zero for your work piece on the Shopbot.
* Is the correct bit installed and tight?
* Is the key in and turned on?
* Is the dust skirt set right so it does not get smashed.
* Is Z zero set to the work top?
* Is the touch plate and clip returned.
* Is the material properly secured
* Safety glasses, hearing protection on.
* Start the job with the E-Stop ready to hit.
* Turn on dust collector ( I like to wait so I can hear that things sound right on the shopbot before turning on the collector)

= Authorized Users =
{| class="wikitable" border="1"
! Authorized Member
! Trained By
|-
|Elizabeth Koprucki
|Danger Committee
|-
|Bart Dring
|Danger Committee
|-
|Ryan Pierce
|Danger Committee
|-
|Nathan Ellis
|Danger Committee
|-
|Michael Skilton
|Danger Committee
|-
|Arturo Duarte
|Bart
|-
|Derek Bever
|Bart
|-
|Everett
|Bart
|-
|Vincent Colombo
|Bart
|-
|[[User:justin|Justin T. Conroy]]
|Bart
|-
|Hugh Sato
|Bart
|-
|Sergey Nekrasov
|Bart
|-
|Valerie Moore
|Bart
|-
|Patrick Schless
|Bart
|-
|Tom Forajter
|Bart
|-
|Todd Allen
|Michael Skilton
|-
|[[User:RogerMoore|Roger Moore]]
|Bart
|-
|Tim Saylor
|Bart
|-
|Hef
|Bart
|-
|Jeff McBride
|Bart
|-
| Maxwell ?
| Michael Skilton
|-
|Samuel Swope
|Michael Skilton
|-
| Khoi Nguyen
|Michael Skilton
|-
|Brian Chojnowski
|Michael Skilton
|-
|Josh Cooper
|Bart
|-
|Andrew Camardella
|Bart
|-
|Adam Glick
|Bart
|-
|Yehuda Braun
|Bart
|-
| Jeff Kantarek
| Michael Sklton
|-
| Justin Miles
|Michael Skilton
|-
|Will Garza
|Michael Skilton
|-
|Clarence Risher
|Michael Skilton
|-
|[[User:ericbeau|Eric Beauchamp]]
|Michael Skilton
|-
|[[User:Jason|Jason]]
|Michael Skilton
|-
|Eric Stein
|Bart
|-
|Colin Parsons
|Bart
|-
|David Ditzler
|Bart
|-
|Ray Doeksen
|Bart Dring
|-
|Ron Bean
|Khoi Nguyen & Michael Skilton
|-
| Thomas Wright
|Khoi Nguyen & Michael Skilton
|-
|David Morton
|Bart Dring
|-
|Ron Olson
|Bart Dring
|-
|Kyle Bieneman
|Bart Dring
|-
|[[User:amishhammer|Tom Judge]]
|Michael Skilton
|-
|Bryan Gleason
|Michael Skilton
|-
|Dave Schact
|Ryan Pierce
|-
|Chris Agocs
|Andrew Camardella
|-
|[[user:kuroishi | Doorman Dave ]]
|Andrew Camardella
|-
|Alec Weege
|Andrew Camardella
|-
|Sam Reicks
|Andrew Camardella
|-
|Touly Phiachantharath
|Andrew Camardella
|-
|Lucas Goossen
|Andrew Camardella
|-
|[[user:Tina|Tina C]]
|Andrew Camardella
|-
|Ryan Neuman
|Andrew Camardella
|-
|Dan Loeser
|Andrew Camardella
|-
|Ben Bogler
|Andrew Camardella
|-
|Erin Banwell
|Ryan Pierce
|-
|Brad Rios
|Ryan Pierce
|-
|Aaron Carlock
|Andrew Camardella
|-
|James Villalpando
|Andrew Camardella
|-
|Connor Jansen
|Andrew Camardella
|-
|Tait Leswing
|Bart
|-
|Raj Perera
|Khoi Nguyen
|-
|Keith Hultman
|Andrew Camardella
|-
|David Srebro
|Andrew Camardella
|-
|[[user:Wessing | Erik Wessing ]]
|Andrew Camardella
|-
|Leeswann Bolden
|Andrew Camardella
|-
|Josh Myers
|Andrew Camardella
|-
|Kurt Ziegel
|Andrew Camardella
|-
|Glenn Powers
|Andrew Camardella
|-
|[[User:mqudsi|Mahmoud Al-Qudsi]]
|Andrew Camardella
|-
|Casey Olson
|Khoi
|-
|Mike Jones
|Andrew Camardella
|-
|Aaron Feigen
|Andrew Camardella
|-
|Jim Baker
|Andrew Camardella
|-
|Eric Reusche
|Khoi Nguyen
|-
|Ralph Brendler
|Andrew Camardella
|-
|John McDonald
|Andrew Camardella
|-
|Alex Al-Hamdan
|Andrew Camardella
|-
|Eugene Liokumovich
|Andrew Camardella
|-
|Randal Cox
|Andrew Camardella
|-
|Simon Pyle
|Andrew Camardella
|-
|Jean Michel Crettaz
|Andrew Camardella
|-
|Brian Zable
|Andrew Camardella
|-
|Daylan Dufelmeier
|Andrew Camardella
|-
|Steve Kruse
|Matt Meshulam
|-
|Mike Mandrea
|Andrew Camardella
|-
|Jeff Zelnio
|Andrew Camardella
|-
|Aaron Stoddart
|Matt Meshulam
|-
|Koun Park
|Matt Meshulam
|-
|Dan Baltudis
|Matt Meshulam
|-
|Curtiss Cooke
|Matt Meshulam
|-
|Jeannine Chuchan
|Matt Meshulam
|-
|Brennan Koziarz
|Matt Meshulam
|-
|Brandon Love
|Matt Meshulam
|-
|Mike Vitale
|Matt Meshulam
|-
|Emma Purola
|Matt Meshulam
|-
|Chris Kohl
|Matt Meshulam
|-
|Daniel Sojka
|Matt Meshulam
|-
|Naguib Azab
|Matt Meshulam
|-
|Mark Zumwalt
|Matt Meshulam
|-
|Joseph Juhnke
|Andrew Camardella
|-
|Alex Berkowitz
|Andrew Camardella
|-
|Andy Muhic
|Matt Meshulam
|-
|Adam Stein
|Matt Meshulam
|-
|John Farmer
|Matt Meshulam
|-
|Joshua Havenga
|Matt Meshulam
|-
|[[user:mct|McTavish McArdle]]
|Matt Meshulam
|-
|Frank Bowles
|Matt Meshulam
|-
|Joe Iklov
|Matt Meshulam
|-
|Matthew Quigley
|Matt Meshulam
|-
|Derwin Umali
|Andrew Camardella
|-
|Doug Mahoney
|Matt Meshulam
|-
|Rob Robinson
|Matt Meshulam
|-
|Dan Sloboda
|Matt Meshulam
|-
|Jacob Collins
|Matt Meshulam
|-
|Donald Wells
|Matt Meshulam
|-
|[[user:jim|Jim Brink]]
|Matt Meshulam
|-
|[[user:mkeith|Matt Keith]]
|Matt Meshulam
|-
|[[user:vmorris|Victoria Morris]]
|Matt Meshulam
|-
|[[user:bobsabayesian|Bob Loos]]
|Matt Meshulam
|-
|[[user:muthpete|Peter Muth]]
|Matt Meshulam
|-
|[[user:guijemont|Guillaume Emont]]
|Matt Meshulam
|-
|[[user:erikthefunk|Erik Funkhouser]]
|Matt Meshulam
|-
|[[user:mrashes|Max Rashes]]
|Matt Meshulam
|-
|[[user:panchan99|Juan Ramos]]
|Matt Meshulam
|-
|[[user:Justjoe|Joe Dowling]]
|Matt Meshulam
|-
|[[user:smash|Ashley Matrisciano]]
|Matt Meshulam
|-
|Ryan Kapp
|Matt Meshulam
|-
|Idris Raja
|Matt Meshulam
|-
|[[user:Dannyblanchard|Danny Blanchard]]
|Matt Meshulam
|-
|Aaron Mintz
|Matt Meshulam
|-
|[[user:ianstubbs|Ian Stubbs]]
|Matt Meshulam
|-
|[[user:skynaya|Skylar Nova]]
|Matt Meshulam
|-
|Chris Ruhland
|Matt Meshulam
|-
|[[user:Jaypee|Jay Pee]]
|Matt Meshulam
|-
|[[user:Ryanmafi|Ryan Fiebing]]
|Matt Meshulam
|-
|[[user:sblaszak|Shawn Blaszak]]
|Matt Meshulam
|-
|[[user:tonyiacullo|Tony Iacullo]]
|Matt Meshulam
|-
|Mark Haughey
|Matt Meshulam
|-
|Chris Iacullo
|Matt Meshulam
|-
|Ian Monroe
|Matt Meshulam
|-
|Ashish Jasani
|Matt Meshulam
|-
|Kurt Gilman
|Matt Meshulam
|-
|Abel Greenwald
|Matt Meshulam
|-
|Vaidotas (Vai) Staugaitis
|Matt Meshulam
|-
|Leo Battikhi
|Matt Meshulam
|-
|Matt Schaid
|Matt Meshulam
|-
|Jamie Vollmer
|Matt Meshulam
|-
|Bhairavi Warke
|Matt Meshulam
|-
|Denis Kuznetsov
|Matt Meshulam
|-
|Brian Carstensen
|Matt Meshulam
|-
|Rob Dumas
|Matt Meshulam
|-
|Mark Weiser
|Matt Meshulam
|-
|Tom Burtonwood
|Matt Meshulam
|-
|Steve Madonna
|Matt Meshulam
|-
|Jason Araujo
|Matt Meshulam
|-
|Bruce Alan Mace
|Matt Meshulam
|-
|Molly Adamski
|Matt Meshulam
|-
|Jeremy Shaw
|Matt Meshulam
|-
|Sam Chen
|Matt Meshulam
|-
|John McBride
|Matt Meshulam
|-
|Adomas Tautkus
|Matt Meshulam
|-
|Tim Buckley
|Matt Meshulam
|-
|Martina Josimovska
|Matt Meshulam
|-
|James Jacobs
|Matt Meshulam
|-
|George Shaw
|Matt Meshulam
|-
|David Earl
|Matt Meshulam
|-
|[[User:pedrosk| Eduard Breuer]]
|Matt Meshulam
|-

|}

If you have been authorized but cannot log in, request to be added to the "ShopBot Authorized" Samba group (send an email to info (at) pumpingstationone.org with your username and the name of the person who certified you) so that your login works. If you don't have a log-in on https://members.pumpingstationone.org/ you will have issues here - sign up on that site first if you haven't already.

= Maintenance =

== Maintenance Log ==
{| class="wikitable" border="1"
!Date
!Preformed by
!Service Type
!Notes
|-
|4/16/2017
|Ryan Pierce
|Created new AutoDesk Fusion 360 Post Processor. Modified Vectric Post Processors.
|Created new Fusion 360 Post Processor. It includes the changes listed below for the Vectric Post Processors. For Vectric, modified the Post Processors so that if the spindle does not spin up, it gives the user a Retry/Cancel dialog box instead of Abort/Retry/Ignore where Ignore is identical to Retry. Also, these Post Processors broke the Preview mode in the ShopBot software because the preview mode did the real spindle check and it failed because, of course, the spindle wasn't running. The new version will ignore the spindle check in preview mode.
|-
|11/8/2014
|Ryan Pierce
|Updated VCarve Post Processor
|Previously, installed new Post Processor to preset an Abort / Retry / Ignore dialog box when the spindle is started but doesn't spin up. Usual culprit is that a job is started when the the interlock is disabled, which results in the non-spinning bit crashing into the workpiece. Abort stops the job. Today, fixed Retry code. If you power on the VFD and the motor start is enabled, the VFD refuses to start. So I've re-programmed the Retry button to stop the VFD, wait 2 seconds, start the VFD, wait 2 more seconds, and check again to see if it is running. The Ignore button actually acts as Retry because we don't want someone clicking through this dialog box and damaging the machine. NOTE: The Aspire PC in the shop also has this Post Processor, but if you use Aspire, VCarve Pro, etc. on your personal computer, you will need the latest Post Processor to support this safety check.
|-
|11/8/2014
|Ryan Pierce
|Updated ShopBot software
|Did upgrade from 3.8.14 to 3.8.26. Installed latest firmware on ShopBot controller. (This was mandatory.) Two features of interest: Fixed occasional erractic behavior after repeated Stops and Resumes (and Nudges or Command Insertions). Reduced liklihood of Keypad lockup.
|-
|5/31/2015
|Ron Olson
|Created new VCarve Post Processors
|For drag/engraving bits, it's important that the spindle be turned '''off''' so as to not destroy the bit. Instead of manually modifying the sbp every time to remove the check that the spindle is turned on, I created a couple of new post processors (inches and mm, similar to Ryan's), that explicitly ''turn off'' the spindle. The user is given two opportunities to cancel the job if that is not what he/she wants.
|-
|}

== Outstanding Maintenance Issues ==

=== Lack of True E-Stop ===
As shipped, the ShopBot PRS does not support an Emergency Stop. This could be hacked, but it runs the risk of damaging the machine if engaged in a non-emergency situation. Suggested solution: Installing a 10A double pole 24V coil DIN mount relay, and powering the coil via the 24V supply through a normally closed E-Stop button. One pole will disconnect the 63V stepper motor current. One pole will break the control signal that enables the VFD and will cause the VFD to brake to a stop.

=== Automatic Dust Collection ===
The ShopBot has +5V TTL outputs that could be used to trigger automatic dust collection (when the spindle goes live) and/or a warning light (when the gantry is enabled to move.)

=== Limit Switch Issues ===
Every time you start the ShopBot, it resets itself so that the limit switches are disabled! You can turn them on (if memory serves) with the Values -> Input Switch Assignment menu item. Limit switches are really useful - but they need to be enabled. When they are, they will stop manual jogging when the limit is hit (although pressing the key again will let you continue moving the gantry) and they will also stop a running job (but give you the option of ignoring the limits.)

I found a couple more problems when testing all the limits. When I took the gantry to X maximum, the dust collector hose pulled off! I put it back on, but I'm not sure how stable this is. Also, when I originally set the Y maximum and minimum, I wanted as much spindle travel as possible. But it appears that if you're at the Y max and move in the X direction, you can hit the middle support with the dust collector boot. We've got several inches Y travel beyond the nominal 48", so we may want to look into reducing this to clear the supports.

== Resources ==
[[File:ShopBot PSOne Post Processors.zip]] - Post Processors for Vectric Aspire and VCarve Pro 8.0 which includes the change to check that the spindle actually started.

[[File:ShopBot_TC_PS1-NO-SPIN.zip]] - Post Processors for Vectric Aspire and VCarve Pro which include changes to explicitly *disable* spinning

[[File:ShopBot PSOne Fusion 360 Post Processor.zip]] - Post Processor for Autodesk Fusion 360 which includes the change to check that the spindle actually started.

[[Category:Fabrication]]
[[Category:CNC]]
[[Category:Future Things Bus Data Sources]]

Lulzbot Taz3

2017-04-15T18:05:02Z

Pedrosk: /* List of Currently Certified Users */

{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = no
|model = Aleph Objects Taz3
|serial = KT-PR0013-5509
|arrived = January 2014
|doesitwork = yes
|contact = [[CNC|CNC Area Host]]
|where = [[CNC]] 2nd Floor
|value = $2395
|image = Taz3.jpg
|hostarea = CNC
}}

== Current Status ==

As of 1/29/2017, things for the Taz3 are ''looking pretty good.'' It is operating as expected and a nice new printed spool holder is being installed on the top. [[User:Skynaya|Skynaya]] ([[User talk:Skynaya|talk]]) 09:48, 29 January 2017 (CST)

== Past Status ==
Still no Octoprint as of 4/4/2017 :(

As of 1/17/2017 there appears to be an issue with Repetier where the server has to be stopped after boot or the COM port will be blocked. It can be disabled by going to the start menu and finding "Stop Server" for Repetier, but you may need admin credentials to override it. I'm looking into disabling this behavior. However, we will be switching to Octoprint servers to operate the printers soon. [[User:Skynaya|Skynaya]] ([[User talk:Skynaya|talk]]) 14:06, 18 January 2017 (CST)

As of 12/28/2016 device was jammed due to improper movement. Currently being worked on. --[[User:Skynaya|Skynaya]] ([[User talk:Skynaya|talk]]) 16:41, 3 January 2017 (CST)

As of 12/20/2015 Someone has put a note saying "no work" on the print bed, no further information known.

As of 12/10/2015 Undergoing testing. Functional. New LCD installed, SD card reader should be working but has not been tested in use. Fiberglass flexible print bed add-on installed. Firmware updated for new Hexagon extruder heads, no longer compatible with Flexistruder, for now. Hexagon heads need to be set higher than old heads (temperatures will need to be higher.) Additional testing required to advise what temperatures are best. --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 16:17, 10 December 2015 (CST)

As of 11/13/2015 the main PLA/ABS extruder is not working, replacement extruders and parts are ordered or awaiting installation by CNC Area Host.

As of 9/28/2015 not clogged, working normally, DO NOT RUN PLA for longer than 1hr --[[User:Rtystgeeke|Rtystgeeke]] ([[User talk:Rtystgeeke|talk]]) 15:26, 28 September 2015 (CDT)

As of 7/20/2015 nozzle clogged with PLA, resistor wire is broken (needs replacement), bottom wood disk is broken (needs replacement) --Andrew Camardella 7/20/2015 5:35pm

As of 6/3/2015 nozzle unclogged, tested with ABS. --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 19:22, 3 June 2015 (CDT)

As of 6/1/2015 clogged with PLA through the length of the hot end and nozzle. Needs to be disassembled, burned out, nozzle cleaned. Probably needs replacement nozzle. Needs replacement parts for the hot end (wood discs, maybe aluminum disk) --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 18:53, 1 June 2015 (CDT)

As of 5/20/2015 not clogged, running normally.

Seems to be extruding fine as of 4/30/2015. [Extruder nozzle clogged. Needs unclogging or nozzle replacement. (As of 4/28/2015, clogged )]

== Authorization ==

Under construction. Ask CNC Area Host. No regularly scheduled authorizations. Authorization sessions can be arranged for 3 or more members as required. If you want to schedule an authorization session, find 2 or more other people (by asking on the Google Group) and email the CNC Area Host for referral to an authorizer.

== Operation ==
* Turn the printer off when you are no longer using it.

== Troubleshooting ==

Under construction. Please add information to this section if you discover some useful tips and tricks.

*Usually is COM5
*If you can't connect on COM5, you may need to reboot the PC, because another user is still logged in after they connected on COM5. If a reboot doesn't resolve the "Connect" problem, then shut the PC down, unplug the unit's power cord, and restarting the machine. This has has fixed the problem as of 3/19/17 - first time I've had the COM5 problem for a while.
*Make sure baud rate is set to 115200
*Make sure protocol is set to Autodetect
*In Repetier Host, home the machine to get full motion on the axes
*In Simplify3D, if you are asking for login information just close the box with the X button and the program will launch.

== Mods ==
Factory standard settings, accessories and equipment. Alternate Flexistruder available at PS1 but not installed.

=== Windows Drivers ===
Windows users driving the printer tethered (over a USB cable) will need to [https://www.lulzbot.com/support/TAZ install drivers.]

=== Usable Print Area ===
298mm x 275mm x 250mm (11.7in x 10.8in x 9.8in)

=== Nozzle size ===
* 0.50 mm nozzle --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 16:20, 10 December 2015 (CST)(please verify?)

=== Host Software ===
Users of Linux, Windows, OSX will need to install the following software:
* [https://github.com/kliment/Printrun#getting-printrun Pronterface] - or [http://www.repetier.com/download/ Repeteir-Host] for manual operation of the printer as well as for starting print jobs
* [http://slic3r.org/download Slic3r] - for creating gcode (print jobs) from 3D models
* Additionally, Lulzbot provides a [http://devel.lulzbot.com/TAZ/2.1/software/2013Q4/slic3r/config/pt35mm-nozzle/medium_ABS_no-support_pt35nzl_pt2-layer-height_config.ini slic3r config file] for the Taz3
* Alternately, you can use [http://wiki.ultimaker.com/Cura Cura by Ultimaker]

== Suggested Settings ==

Both of these files have appropriate settings for the 'printer settings' and 'filament settings' tabs. To use them, go to File > Load Config in Slic3r and select the downloaded file. You must then go to each tab and hit the 'save' icon next to the settings selection dropdown box, or else Slic3r will forget the settings when you close it.

For settings in Simplify3D, you need to 'import FFF profile'. This can be found under File/Import FFF Profile, then browse your computer to find it.

==== ABS for Simplify3D ====

[[File:ABS Fast2.0(.3mm).zip]]

ABS profile for the Taz3 at %15 infill, supports enabled, .3mm layer height, extruder at 230C and bed at 90C, with appropriate cooling (none).

==== PLA for Simplify3D ====

[[File:PLA_Simplify3D.zip]]

PLA profile for the Taz3 at %15 infill, supports enabled, .3mm layer height, extruder at 190C and bed at 65C, with appropriate cooling (increasing speed with layer height).

==== Ninjaflex for Simplify3D ====

[[File:Ninjaflex_Simplify3D.zip]]

Ninjaflex profile for the Taz3 at %15 infill, supports enabled, .3mm layer height, extruder at 220C and bed nonheated.
*Ninjaflex can only be run with the flexistruder extruder type, which requires the firmware "Marlin 2014" or older.

==== ABS Print Settings Without Support - Fast ====

[[File: Taz3_print_settings_NO_SUPPORT.ini]]

This file is for the 'print settings' tab of Slic3r. This is a 'fast' profile, geared towards finishing prints relatively quickly. It still provides excellent surface quality. This profile does not include support, so for large overhangs you'll need the next configuration file.

==== ABS Print Settings With Support - Fast ====

[[File: Taz3_print_settings_SUPPORT.ini]]

This file is for 'print settings' tab of Slic3r. This is a 'fast' profile, geared towards finishing prints relatively quickly. It still provides excellent surface quality. This profile includes support, appropriate for large overhangs.

==== Skylar's Config Bundle ====

[[File:Sky config bundle.zip]]

Here is a range of configuration settings for Slic3r in Repetier that I've found useful with a lot of trial and error. [[User:Skynaya|Skynaya]] ([[User talk:Skynaya|talk]]) 21:35, 13 April 2017 (CDT)

== Other Resources ==
[http://download.lulzbot.com/TAZ/3.0/documentation/2013Q4/LulzBot_TAZ_3.0-User_Manual-ebook.pdf The manual is available online]. A printed form of it can be found near the printer. The manual explains how to operate the printer.

[https://wiki.pumpingstationone.org/images/Basic_ABS_Settings_for_Taz_with_Repetier_Host_software.pdf This PDF] contains the screenshots for each tab and setting. When you first use Repetier on your windows login, you have to adjust some settings for first time use.

=== Filament ===

The extruders available accept 3 mm filament, and can print either ABS or PLA. There is an alternate extruder for use with Ninjaflex, called 'Flexistruder' but the Flexistruder is not supported with the current firmware installation.

[http://www.microcenter.com/category/4294898923/3D-Printing MicroCenter (online and in store)]

[http://www.monoprice.com/Search/Index?keyword=3d+printer+filament Monoprice]

=== Find Something to Print ===

[http://thingiverse.com Thingiverse] is a great place to find printable 3D models that other people have designed, and to publish your own.

=== Designing 3D Models ===

Page in progress to describe [https://wiki.pumpingstationone.org/3D_Modeling 3D modeling.]

== List of Currently Certified Users ==
{| class="wikitable" border="1"
! qualified member
! trained by
|-
|[[User:Dbever|Derek Bever]]
|Hours of shouting at 3D printers
|-
|Elizabeth Koprucki
|Derek Bever
|-
|Andrew Kos
|Elizabeth Koprucki
|-
|[[User:rdoeksen|Ray Doeksen]]
|Elizabeth Koprucki
|-
|[[User:Negativek|Everett Wilson]]
|Derek Bever
|-
|[[User:daveplays|David Earley]]
|Derek Bever
|-
|[[User:Lyn|Lyn Cole]]
|Derek Bever
|-
|[[User:nerobro|Greg Teiber]]
|Derek Bever
|-
|[[User:nick|Nick Castillo]]
|Derek Bever
|-
|[[User:tom4writer|Tom Forajter]]
|Elizabeth Koprucki
|-
|[[User:dditzler|David Ditzler]]
|Elizabeth Koprucki
|-
|[[User:davidfell|David Fell]]
|Elizabeth Koprucki
|-
|[[user:rob|Rob Riggs (Colorado Rob)]]
|Elizabeth
|-
|Mark Stevens
|Elizabeth Koprucki
|-
|[[User:ad9581|Arturo Duarte]]
|Elizabeth Koprucki
|-
|[[User:justin|Justin T. Conroy]]
|Derek Bever
|-
|[[User:jivnyahoo|James Porter]]
|Elizabeth Koprucki
|-
|[[User:ryankelly11|Ryan Kelly]]
|Elizabeth Koprucki
|-
|[[User:JanetD|Janet Dornhoff]]
|Elizabeth Koprucki
|-
|Genevieve Aphrodite
|Justin Conroy
|-
|Sloan Lavery
|Elizabeth Koprucki
|-
|[[User:spacekid|Adam Glick]]
|Ray Doeksen
|-
|[[User:funk|Tyler Natoli]]
|Elizabeth Koprucki
|-
|Chris Marchwick
|Elizabeth Koprucki
|-
|[[User:marty|Marty Dubin]]
|Elizabeth Koprucki
|-
|[[User:amishhammer|Tom Judge]]
|Justin Conroy
|-}
|-
|[[User:brian|Brian Dunn]]
|Derek Bever
|-|-
|[[User:lofgren|Tim Lofgren]]
|Derek Bever
|-
|[[User:lgaboarder|Jeff McBride]]
|Elizabeth Koprucki
|-
|Thomas Wright
|Justin Conroy
|-
|[[User:dsiegfried|David Siegfried]]
|Derek Bever
|-
|Donald Jacobson
|Elizabeth Koprucki
|-
|[[User:Sparr|Clarence Risher]]
|Elizabeth Koprucki
|-
|[[User:ironwill|Will Garza]]
|Elizabeth Koprucki
|-
|[[User:emertonom|Nick Halderman]]
|Elizabeth Koprucki
|-
|[[User:tactics|Michael Maloney]]
|Elizabeth Koprucki
|-
|[[User:tactics|Brennan Koziarz]]
|Elizabeth Koprucki
|-
|[[User:rogermoore|Roger Moore]]
|Elizabeth Koprucki
|-
|[[User:aaronmintz|Aaron Mintz]]
|Elizabeth Koprucki
|-
|[[User:mlm|Matt Makris]]
|Elizabeth Koprucki
|-
|Matt Meshulam
|Elizabeth Koprucki
|-
|Ron Olson
|Elizabeth Koprucki
|-
|[[User:daroldhiga|Darold Higa]]
|Ray Doeksen
|-
|Nora Sluzas
|Elizabeth Koprucki
|-
|Matt Triano
|Elizabeth Koprucki
|-
|Curtiss Cooke
|Elizabeth Koprucki
|-
|Andrew Sowa
|Elizabeth Koprucki
|-
|Eric Yu
|Elizabeth Koprucki
|-
|[[User:lucas|Lucas Goossen]]
|Elizabeth Koprucki
|-
|Jessica Wiedner
|Derek Bever
|-
|Scott Little
|Derek Bever
|-
|Kevin Pulver
|Ray Doeksen
|-
|Jenny Tong
|Ray Doeksen
|-
|Mike Mandrea
|Elizabeth Koprucki
|-
|John Farmer
|Elizabeth Koprucki
|-
|Andy Richardson
|Elizabeth Koprucki
|-
|Alex Trimm
|Elizabeth Koprucki
|-
|[[User:rickalm|Rick Alm]]
|Elizabeth Koprucki
|-
|Davis Mazariegos
|Elizabeth Koprucki
|-
|Knute Martell
|Elizabeth Koprucki
|-
|Hugh Sato
|Elizabeth Koprucki
|-
|Ryan Neuman
|Will Garza
|-
|[[User:Tina|Tina C]]
|Elizabeth Koprucki
|-
|Scott Drane
|Elizabeth Koprucki
|-
|Michael Patton
|[[User:rdoeksen|Ray Doeksen]]
|-
|Chris Leeson
|[[User:rdoeksen|Ray Doeksen]]
|-
|Matt Pollina
|[[User:rdoeksen|Ray Doeksen]]
|-
|Scott Anamizu
|[[User:rdoeksen|Ray Doeksen]]
|-
|[[user:kuroishi|Doorman Dave]]
|Elizabeth Koprucki
|-
|Simon Pyle
|[[User:rdoeksen|Ray Doeksen]]
|-
|Brad Jiminez
|[[User:rdoeksen|Ray Doeksen]]
|-
|Nate Scheidler
|[[User:rdoeksen|Ray Doeksen]]
|-
|Alan Insley
|[[User:rdoeksen|Ray Doeksen]]
|-
|Wessing
|[[User:rdoeksen|Ray Doeksen]]
|-
|[[User:w9lp|Casey Coley]]
|Andrew Camardella
|-
|Deanna Williams
|Brad Jimenez
|-
|Jim Hartmann
|Ray Doeksen --[[User:Rdoeksen|Rdoeksen]] ([[User talk:Rdoeksen|talk]]) 14:44, 20 September 2015 (CDT)
|-
|Hunter Koerner
|Ray Doeksen
|-
|Temnulen Erdenekhun
|Ray Doeksen
|-
|Greg Teiber
|Ray Doeksen
|-
|Bob Williams
|Ray Doeksen
|-
|Elizabeth Arundel
|Brad Jimenez
|-
|Alex Al-Hamdan
|Brad Jimenez
|-
|Nem Simeunovic
|Brad Jimenez
|-
|Dafe Hughes
|Brad Jimenez
|-
|Gary Silver
|Brad Jimenez
|-
|Daniel Maziarz
|Brad Jimenez
|-
|Greg Kudlacz
|Brad Jimenez
|-
|Adam Moffatt
|Brad Jimenez
|-
|Kevin Schwartzenberg
|Andrew Camardella
|-
|Michael Slingerland
|Andrew Camardella
|-
|Andrew Dalesandro
|Andrew Camardella
|-
|Erik Funkhouser
|Brad Jimenez
|-
|Elizabeth Carter
|Brad Jimenez
|-
|Idris Raja
|Brad Jimenez
|-
|Shelly Loke-Gayares
|Brad Jimenez
|-
|Craig Koszewski
|Brad Jimenez
|-
|Brandon Love
|Brad Jimenez
|-
|Todd Allen
|Andrew Camardella
[[Category:Fabrication]]
[[Category:CNC]]
|-
|Parker Rueve
|Brad Jimenez
|-
|Mike Czubak
|Brad Jimenez
|-
|Paula Brinkman Lowe
|Brad Jimenez
|-
|Xander Czubak
|Brad Jimenez
|-
|Angus Brinkman Lowe
|Brad Jimenez
|-
|Chris Smith
|Brad Jimenez
|-
|James Villalpando
|Brad Jimenez
|-
|Zachariah Reed
|Brad Jimenez
|-
|Calvin Moravec
|Brad Jimenez
|-
|Joshua Havenga
|Brad Jimenez
|-
|Skylar Nova
|Andrew Camardella
|-
|Brian Carstensen
|Andrew Camardella
|-
|Aaron Carlock
|Andrew Camardella
|-
|Rob Dumas
|Andrew Camardella
|-
|Mike Kirda
|Skylar Nova
|-
|Ashley Borg
|Skylar Nova
|-
|Ed Breuer
|Skylar Nova
|-
|Mark Haughey
|Skylar Nova
|}

Tier 1 Cold Metals Authorization

2017-04-11T05:10:29Z

Pedrosk: /* People who are Tier 1 Authorized for Cold Metals Area */

In the cold metals area we have grouped together authorizations on the non-precision cutting tools into a single authorization called "Tier 1". ''The handout (the "script") we use is at [[Cold Metals Tier 1]]''. The [[DoAll Drill Press]], [[Bench Grinder (6in)]], [[Sears Belt Sander|Belt Sander]], [[Johnson Bandsaw]], [[DoAll Bandsaw]], [[DeWalt Chop Saw]] are under a Tier 1 authorization process. The session covers basic operation and safety on the machines.

Monitor the mailing list for times and dates.

== Tools Requiring Tier 1 ==

[[Clausing Lathe|Clausing metal lathe]]

[[Bridgeport Knee Mill|Bridgeport milling machine]]

== Cold Metals Tier 1 Authorizers ==

Tier 1 authorization can currently be done by the following people:

{| class="wikitable" border="1"
! Tier 1 Authorizers
|-
|Michael Patton - Primary
|-
|Ed Bennett
|-
|Anna Yu
|-
|Tucker Tomlinson
|-
|Thomas Wright
|-
|Todd Allen
|-
|Everett Wilson
|-
|Chris Ruhland
|}

=== How to become a Authorizer ===

We want as many people available to do Tier 1 authorizations as we can get.
The idea is to promote safety, and get people used to the sounds that a machine tool cutting well makes.
New authorizers get authorized to authorize others by (1) having some
amount of presence in the shop and (2) closely following the "script"
during EITHER a "dry-run" authorizing session given to an authorized
authorizer -- or conducting a real-live authorizing session while being
observed by an authorized authorizer. During such a session, the
observing authorizer should _not_ have to speak. Obviously if the new
authorizer-to-be has _significant_ problems in communication of the
content of the "script", the observing authorizer will contribute to the
discussion. For the new authorizer-to-be it's a test, not an opportunity
for team-teaching.

==== Tier 1 Cold Metals Areas Convention of Authorization ====

[[Cold Metals Tier 1]]

== People who are Tier 1 Authorized for Cold Metals Area ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
!Date Trained
|-
|Adam Glick
|Ed Bennett
|
|-
|Jeffrey Camealy
|Ed Bennett
|
|-
|Tina Croniser
|Ed Bennett
|
|-
|Sevin Straus
|Ed Bennett
|
|-
|Vladamir Riazanski
|Ed Bennett
|
|-
|James Porter
|Ed Bennett
|
|-
|Greg Teiber
|Ed Bennett
|
|-
|Everett Wilson
|Ed Bennett
|
|-
|Derek Bever
|Ed Bennett
|
|-
|Jay Hopkins
|Ed Bennett
|
|-
|James Porter
|Ed Bennett
|
|-
|Eric Stein
|Tucker Tomlnson
|
|-
|Todd Allen
|Ed Bennett
|
|-
|Mac MacDevitt
|Ed Bennett
|
|-
|[[User:scyg|Simon Cygielski]]
|Ed Bennett
|
|-
|Robb Rigs
|Ed Bennett
|
|-
|Arturo Duarte
|Ed Bennett
|
|-
|Michael Skilton
|Tucker Tomlinson
|
|-
|[[User:Justin|Justin T. Conroy]]
|Ed Bennett
|
|-
|[[User:davidfell|David Fell]]
|Ed Bennett
|
|-
|[[User:rdoeksen|Ray Doeksen]]
|Ed Bennett
|
|-
|Ryan Pierce
|Ed Bennett
|
|-
|Elizabeth Koprucki
|Ed Bennett
|
|-
|Casey Olson
|Ed Bennett
|
|-
|Ron Olson
|Ed Bennett
|
|-
|Thomas Wright
|Ed Bennett
|
|-
|Tom Judge
|Tucker Tomlinson
|
|-
|Edward Muela
|Anna Yu
|5/13/14
|-
|Samuel Swope
|Anna Yu
|5/13/14
|-
|Chris Agocs
|Anna Yu
|6/3/14
|-
|Justine Miles
|Anna Yu
|6/3/14
|-
|Robert Grossman
|Ed Bennett
|
|-
|Tom Forajter
|Thomas Wright
|
|-
|[[User:ahbaker|Alan Baker]]
|Tucker Tomlinson
|
|-
|Jeff McBride
|Ed Bennett
|10/9/14
|-
|Mike Kislovsky
|Ed Bennett
|10/9/14
|-
|Arjun Wadnerkar
|Ed Bennett
|10/9/14
|-
|Oscar Villareal
|Ed Bennett
|10/9/14
|-
|TomF (? 7-17)
|Thomas Wright
|
|-
|Rich Smith
|Thomas Wright
|
|-
|George Shaw
|Thomas Wright
|
|-
|Ron Bean
|Ed Bennett
|
|-
|John Butera
|Ed Bennett
|10/18/14
|-
|Alex Schaffer
|Ed Bennett
|10/18/14
|-
|Daniel Loeser
|Ed Bennett
|10/18/14
|-
|Jonathan Bisson
|Ed Bennett
|10/18/14
|-
|Kyle Bieneman
|Todd Allen
|11/09/14
|-
|Scott Little
|Todd Allen
|11/09/14
|-
|RJ Metzger
|Todd Allen
|11/09/14
|-
|Giovanni Arroyo
|Todd Allen
|11/09/14
|-
|Joao Santos
|Todd Allen
|11/26/14
|-
|Nicholas Haldereman
|Todd Allen
|11/26/14
|-
|Doorman Dave
|Todd Allen
|11/26/14
|-
|Stephen Ioannou
|Todd Allen
|11/26/14
|-
|Lucas Goossen
|Todd Allen
|12/10/14
|-
|[[user:RogerMoore|Roger Moore]]
|Todd Allen
|12/10/14
|-
|[[User:Mwilkens|Matt Wilkens]]
|Todd Allen
|12/10/14
|-
|Rhonda Jackson
|Todd Allen
|12/10/14
|-
|Matt Meshulam
|Todd Allen
|12/21/14
|-
|Kevin Pulver
|Todd Allen
|12/21/14
|-
|Andrew Camardella
|Todd Allen
|12/21/14
|-
|Mike Coriale
|Todd Allen
|12/21/14
|-
|Nick Naro
|Todd Allen
|1/11/15
|-
|John Farmer
|Todd Allen
|1/11/15
|-
|[[user:Jaypee|Jay Pee]]
|Todd Allen
|1/11/15
|-
|Sam Paris
|Todd Allen
|1/21/2015
|-
|Jake Rush
|Todd Allen
|1/21/2015
|-
|Carolyn Ignacio
|Todd Allen
|1/21/2015
|-
|Andrew Sowa
|Todd Allen
|1/21/2015
|-
|Hilary Lee
|Todd Allen
|1/21/2015
|-
|Eric Slehofer
|Todd Allen
|1/28/2015
|-
|Sam Reicks
|Todd Allen
|1/28/2015
|-
|Tyler Matthew
|Todd Allen
|1/28/2015
|-
|Ben Bogler
|Todd Allen
|1/28/2015
|-
|Brittany Krawczyk
|Todd Allen
|1/28/2015
|-
|Cary Lahucik
|Todd Allen
|1/28/2015
|-
|Eric Yu
|Todd Allen
|2/8/2015
|-
|Davis Mazariegos
|Todd Allen
|2/8/2015
|-
|Dan Baltudis
|Todd Allen
|2/8/2015
|-
|Shae Kurko
|Todd Allen
|2/25/2015
|-
|Curtiss Cooke
|Todd Allen
|02/08/15
|-
|Ryan Taylor
|Everett Wilson
|03/04/15
|-
|Joe Wallace
|Todd Allen
|03/08/15
|-
|Josh Myers
|Todd Allen
|03/08/15
|-
|[[User:glenn|Glenn Powers]]
|Todd Allen
|03/08/15
|-
|Daniel Sojka
|Todd Allen
|03/25/2015
|-
|Michael Patton
|Todd Allen
|03/25/2015
|-
|Kevin M Sampson
|Todd Allen
|07/22/2015
|-
|Steve Farkas
|Everett Wilson

|-
|Josh Cooper
|Todd Allen
|09/30/2015
|-
|Sheila Miguez
|Everett Wilson
|2015/12/29
|-
|Zonghe Chua
|Michael Patton
|1/10/16
|-
|Brandon Love
|Michael Patton
|1/27/16
|-
|John McDonald
|Michael Patton
|3/6/16
|-
|Zachery Small
|Michael Patton
|5/1/16
|-
|Josh Younger
|Michael Patton
|5/7/16
|-
|Andy Muhic
|Michael Patton
|5/7/16
|-
|Spencer Simms
|Michael Patton
|5/26/16
|-
|Noah Lambert
|Michael Patton
|6/15/16
|-
|Ian Monroe
|Michael Patton
|6/29/16
|-
|Joe Iklov
|Michael Patton
|6/29/16
|-
|Jim Brink
|Michael Patton
|6/29/16
|-
|[[user:mct|McTavish McArdle]]
|Michael Patton
|2016-07-10
|-
|Patrick Bowling
|Michael Patton
|8/14/16
|-
|Ashley Matrisciano
|Michael Patton
|8/14/16
|-
|Juan Ramos
|Michael Patton
|8/14/16
|-
|Leo Rodman
|Dean?
|9/14/16
|-
|Dan Conrad
|Michael Patton
|10/05/16
|-
|Aaron Mintz
|Michael Patton
|10/20/16
|-
|Brian Carstensen
|Michael Patton
|10/20/16
|-
|Chris Ruhland
|Michael Patton
|11/7/16
|-
|Simon Pyle
|Michael Patton
|12/5/16
|-
|Josip Fijacko
|Michael Patton
|12/5/16
|-
|Adam Stein
|Michael Patton
|1/14/17
|-
|Paul McClay
|Chris Ruhland
|3/23/17
|-
|Ed Breuer
|Chris Ruhland
|04/09/2017
|-

Tier 1 Cold Metals Authorization

2017-04-11T05:09:55Z

Pedrosk: /* People who are Tier 1 Authorized for Cold Metals Area */