PS:1 Wiki Dev - User contributions [en]

Shopbot PRS CNC router

2020-01-26T15:28:24Z

Rfoto:

{{Template:EquipmentPage
|owner = PS:One
|serial = TBD.
|certification = yes
|hackable = no
|model = Shopbot PRS #10108 96-48
|arrived = 2014
|image = Shopbot.jpg
|doesitwork = yes
|contact = [[CNC|CNC Area Host]]
|where = Wood Shop
|value = $16000
|hostarea = CNC
}}
= ShopBot PRS #10108 96-48 =

* [http://www.shopbottools.com/mProducts/prSstandard.htm OEM website and specs]
* Nominal Cutting Area 96"x 48"x 6" (2.44m x 1.22m x .15m)
* Total Movement Area 102" x 50" x 8" (2.59m x 1.27m x .20m)
* Max spindle speed: 18000 RPM
* Min spindle speed: 4100 RPM

The spindle uses ER25 collets. These eventually wear out, so check before using them. Collets are a durable expendable.

Some people buy their own collets. There are a number of suppliers of collets, nuts, and related accessories. [http://www.techniksusa.com/ Techniks] and [http://www.shars.com/ Shars] are both brands that have been recommended by experienced CNC users, although other brands may also be of equivalent price and quality:

* [http://www.shars.com/1-4-ultra-precision-5-micron-er25-collet Shars ER25 Collet Ultra Precision 5 Micron]
* [https://www.ebay.com/itm/TECHNIKS-1-4-SUPER-PRECISION-ER25-COLLET-0002-ACCURACY-CNC-CHUCK-MILL-/130701349603?hash=item1e6e6852e3 Techniks 1/4" Super Precision ER25 Collet .0002 Accuracy]
* [https://www.toolstoday.com/cnc-high-precision-spring-collets-for-er25-tool-holder.html?variantids=11644,0&keywords=CO-286 Amana CNC High Precision Spring Collets for ER25 Tool Holder]
* [https://www.amazon.com/HHIP-3900-5215-ER-25-Spring-Collet/dp/B01ABWS9IG/ HHIP 3900-5215 ER-25 Spring Collet, 1/4"]
* [https://www.amazon.com/Dorian-Tool-Alloy-Precision-Collet/dp/B00CB14HXW/ Dorian Tool ER25 Alloy Steel Ultra Precision Collet, 0.236" - 0.276" Hole Size]

=Status=
August 2017: Dust collection system out of commission.

June 2017: There is an intermittent break in the wiring for the Z-axis Zero Plate. Check for continuity before using (the #1 input should light up on screen when you touch the contacts together). It usually works near the front of the table, but not halfway back. This will get fixed eventually, but it's a good idea to be in the habit of checking.

12/27/16 - Fixed Shopbot x-axis homing. The cable had been pulled on hard enough that some of the conductors broke inside the cable. It has been spliced, soldered, and heatshrinked back together.

= How to Get Authorized =

'''Authorization for this tool by authorized proctors only.''' This means you cannot get authorized by just anyone who is already authorized. You can only get authorized by a few people, the proctors listed below.

Authorization sessions are scheduled roughly monthly. Check the [https://www.meetup.com/Pumping-Station-One/events/ Meetup calendar] for upcoming authorizations. If no ShopBot sessions are currently scheduled, ask the [[CNC Area Host]] or on the [https://groups.google.com/group/pumping-station-one/ Google Group].

Be aware that this authorization consists of two parts; the first session is a classroom session that will cover the software required and introduce you to the essential settings and chip-load calculation, and the second part, scheduled separately, is a hands-on class.

== Authorizers ==
{| class="wikitable" border="1"
|-
|Elizabeth Koprucki
|Danger Committee
|-
|Bart Dring
|Danger Committee
|-
|Ryan Pierce
|Danger Committee
|-
|Nathan Ellis
|Danger Committee
|-
|Michael Skilton
|Danger Committee
|-
|Khoi Nguyen
|Michael Skilton
|-
|Andrew Camardella
|Elizabeth Koprucki
|-
|Matt Meshulam
|Andrew Camardella
|-
|David Earl
|Matt Meshulam
|-
|}

== How to Become an Authorizer ==
Get an ok from the area host. Successfully run an authorization supervised by an authorizer.
It's recommended that initial authorizations be limited to 2 member participants or less.

= Documentation =

[[File:Shopbotassembly.pdf|Shopbotassembly.pdf]]

[[File:Squaringshopbot.pdf|Squaring the ShopBot]]

[[File:Programming_handbook.pdf|Programming Handbook]]

[[File:PRS Maintenance Schedule.pdf|Maintenance Schedule]]

[[File:ShopBot_USB_Connection_Troubleshoot.pdf]] - USB Troubleshooting Guide

[[File:ShopBot_Tech_Support_FAQ_2016_09_12.pdf]] - Tech Support FAQ

[[File:SBG00142 User Guide 2013 05 01.pdf|SBG00142 User Guide 2013 05 01.pdf]] - User Guide

[[File:B17P.763_Schematic.pdf]] - Omer Nail Gun Documentation

[http://www.shopbottools.com/ShopBotDocs/files/quick%20start%20guide%202013%2007%2023.pdf QuickStart]

X, Y, Z probe: https://pumpingstationone.org/2015/09/xyz-finder-for-the-shopbot/

[http://drshopbot.com/index.php?title=Main_Page "Dr Shopbot" wiki]

[http://drshopbot.com/index.php?title=MaintainingConnection "Maintaining Connections"]

[[File:Shopbotmagnets.ai.zip]] - Template for the dust skirt and magnet placement.

== Tutorials ==
[https://www.youtube.com/watch?v=xWCZfYHOYWw Part 1 of our Shopbot Authorization] - This is available as a refresher only. You still need to go to the class when it happens to get access to the hands-on Part 2.

[http://www.woodguide.org/files/2014/07/CNCrouter_bit_basics.pdf Router Bit Basics for CNC - VERY USEFUL]

[https://groups.google.com/forum/?fromgroups=#!searchin/pumping-station-one/shopbot Shopbot Threads on Member List]

[https://groups.google.com/forum/?fromgroups=#!searchin/pumping-station-one/shopbot Shopbot Forum]

[https://groups.google.com/d/msg/pumping-station-one/vUF3iKRQ9yc/_qNnLXzZ3QcJ Overview of Cut Load calcualtions for setting bit feed and speed rates]

Vertanux1: This user teaches at Elgin Community College and has very good tutorials and downloadable textbook on Autodesk Inventor (which applies to Fusion 360 as well: http://www.vertanux1.com/ and https://www.youtube.com/user/vertanux1?reload=9

Online chipload calculator: https://www.guhdo.com/chipload-calculator

Fusion 360 Videos

NYC CNC - Several videos that provide an overview of downloading software, preferences, and basic sketch terms and steps. https://www.nyccnc.com/fusion-360/

Lars Christensen - CAD/CAM instructor hired by Autodesk to produce their Fusion 360 videos. The Absolute Basics and #LarsLive series are worth watching. https://www.youtube.com/watch?v=A5bc9c3S12g&feature=youtu.be

Maker's Muse CAD for Newbies Series - Provides a detailed overview of sketch dimensions, constraints, revolving, sweeping, and lofting, among many other topics. https://www.youtube.com/playlist?list=PLTCCNNvHC8PC40tcEqaJcgUMb97LNkLIn

Krenov Coffee Table - A fantastic overview of the design of a coffee table from scratch. Lots of CAD best practices. https://www.youtube.com/watch?v=J22j8RfETjs&feature=youtu.be

Fusion 360 V12 Engine - A long playlist series on a complex topic that demonstrates how powerful real CAD software can be. https://www.youtube.com/playlist?list=PLQl9vsO6sGSlasKFP-CAgnDs324Z6IW8s

= Software Tool Chain =
*Illustrator
*Inkscape
*Vectric Aspire
**Allows for 2D and 3D linework and toolpath creation
**Only available on the Shapeoko Computer
*Vectric V-Carve Makerspace Edition Version 9.0 (earlier versions may not be supported here anymore)
** http://www.vectric.com/products/vcarve/trial.html
**Allows for 2D linework and toolpath creation
**Allows at home use of V-Carve - output only at PS1
**Our Makerspace Code is: E4793-F6472-BB9E5-9B114-3FEEB-73649-16F4F
*Autodesk Fusion 360
**The ShopBot computer does not have this and may not be fast enough to run it.
**You '''MUST''' use the custom post-processor below. Otherwise, you will bypass the safety check to make sure the spindle really is running!
**For local '''Windows''', to install this on your local computer:
***Unzip and install this in C:\Users\YourName\AppData\Roaming\Autodesk\Fusion 360 CAM\Posts
***Note that AppData is often a hidden folder!
***Inside Fusion 360, when you select Actions / Post Process, under Configuration Folder, hit Setup and select Use Personal Posts.
**For local '''Mac'''
*** Unzip and install in Macintosh HD> Users> USERNAME> Autodesk> Fusion 360 CAM> Posts
*** In Fusion 360, when you select Actions > Post Process, under Settings select Personal Posts for the Source
**For '''Cloud'''
*** Open Fusion 360 and navigate to Libraries > Assets in the Data Panel.
*** Double click the Assets > CAMPosts folder to enter it.
*** Use the Upload button to upload the desired post processor from your local machine to the Assets > CAMPosts folder. This will upload the post to the cloud and allow you to access it anywhere you may login to your Fusion 360 account through My Cloud Posts.
*** After enabling cloud libraries in Fusion 360, you will be able to access your cloud post processor library by setting the Configuration Folder (Windows) or Source (Mac) to My Cloud Posts. Both of these dialog boxes are shown below. You will then be able to select the Cloud post you uploaded in the Post Configuration field (Windows) or the Post Processor field (Mac).
====Chip Load Calculation====
*[https://www.guhdo.com/chipload-calculator Chip Load Calculator by Guhdo]
*[http://www.pdsspindles.com/engineering-speeds Bit Parameter Overview by PDS Spindles]
*[https://www.monstertool.com/29/tech-data.htm Monster Tools Chip Load Calculator]
*[http://www.pdsspindles.com/admin/modules/page_editor/uploads/image/Chip%20load%20for%20common%20tool%20diameters%20(Inches).jpg Chip Load Chart by PDS Spindles]
*[https://groups.google.com/forum/#!searchin/pumping-station-one/makerspace$20edition/pumping-station-one/cTwfUHxESjU/7m_lI8UWCgAJ How to install Makerspace Version]

== User Tips & Troubleshooting Reports ==
[http://www.sgstool.com/PDF-speedfeeds/SGS-Speeds-Feeds-GP.pdf Some feed and speed recommendations for small bits]

Add your experiences with feeds and speeds or other tips here:
[[Shopbot_User_Tips]]

Add troubleshooting reports here:
[[Shopbot_Troubleshooting_Reports]]

=== Materials ===

* [[Shopbot_PRS_CNC_router/Aluminium|Aluminium]]
* [[Shopbot_PRS_CNC_router/Brass|Brass]]
* [[Shopbot_PRS_CNC_router/Wood|Wood]]

== Authorization Checklist ==

This is here as a checklist for proctors to follow when authorizing people. It can also help remind you of things after you are authorized. Just reading this does not authorizing you.

* How to get authorized
** Watch [http://www.meetup.com/Pumping-Station-One/ the meetup group] for a recurring class on the second Thursday and last Sunday of the month. Sometimes check [https://groups.google.com/forum/#!forum/pumping-station-one the forum] for announcements or ask on the forum if no announcements have been made for a few weeks.

* Authorization group size
** There is no cap to the software instruction preceding the machine usage portion of the class. If you come to this portion it is easier to get fully authorized at a later date.
** 3 machine users - each person will run a job (~1/2 hr each) and everyone will assist each other in completing a job profile and pocket cut. You must be present for the entire authorization

* Safety
** Safety Glasses
** Hearing Protection
** Dust Protection

* What can go wrong (and what to do)

* How does machine work
** Axes
** Motors
** Spindle

* Daily Maintenance
** Spindle bearing warm up.
*** The "C5" warm up routine should be run on the first job of the day. It runs the spindle at 3 speeds for 3 minutes each to warm up the bearings. (When it doubt, warm it up)

* Extended Maintenance
** See maintenance schedule file under documentation.
** Grease the racks
** Use Grease type: Manual states any type is safe there is some in the draw

* Machine Control
** Turn on sequence
*** Log into computer
*** Turn on Shopbot big red and yellow twist switch (see zeroing below)
*** Insert Key and turn to "engaged" position.
*** The VDF should light up, the spindle fan should be on.
*** Start "Shopbot 3" program.
*** Open Tools...Spindle RPM Control menu (to allow RPM control)
**** Make sure collet is tightened or no tool or nut is installed
**** Run the C5 warm up routine
** Jogging
*** Keypad
*** Arrow Keys + Page Up, Page Down (ctrl for fast jog)

* CAM Software
** Vectric V Carve
** Just the basics...separate class for advanced V Carve.
** Online videos

* Running your Job
** Zeroing X & Y
*** With machine off slow push gantry towards X0 until it hits hard stops (optional)
*** Turn on big red switch while still holding gantry.
*** Jog machine away from X0 Y0 so machine will find switches
*** Click X, Y zero button.
** Zeroing Z (top of work piece)
*** Jog over your work piece
*** Place Z zero plate on work piece under the bit
*** Place clip on bit
*** Test connection by touching plate to bit and watch for light #1 to light
*** Click the Z 0 button (it will touch off twice!!!)
*** If Z is critical, you may want to verify that your bit has been zeroed properly by using a "MZ,0" command over the surface you have zeroed the bit to. Repeat zeroing if not correct.

* Waste Board and clamping

* Collets, Bits, Feeds and Speeds
** Feeds and Speeds
*** Use a Cut Load Calculator to determine which feeds and speeds you should be using for your specific bits. An overview is avaialble at: [https://groups.google.com/d/msg/pumping-station-one/vUF3iKRQ9yc/_qNnLXzZ3QcJ]
** Collets
*** We currently have collets for 1/2, 1/4, 3/16 and 1/8" shank bits.
*** Try to keep them clean and store them away from dust between uses. Dust between the gaps will produce runout. The drawer mounted under the Shopbot is the right place to store these items.
*** If the collet nuts are not threading smoothly try cleaning the threads with a small brush, spindle threads as well.
** Bits
*** Use bits designed for the material you are cutting. Don't just steal a bits from the Bridgeport. They won't do a good job and will probably overheat.
*** For cutting out things, use the smallest appropriate bit. Using a 1/2" bit to cutout will just create a lot of mess.

* ShopBot should not be used for...
** Metals other than aluminum
** Cutting anything that requires coolant or lubricant (it will ruin the waste board)
** Ripping lumber (use the table saw)
** Thickness Planning (Use the planner if you can)
** Drilling holes with drill bits (a small end mill works better)

* How to leave the machine (be excellent)
** Machine
*** Home the machine to X0, Y0
*** Turn off both switches
*** Remove Key
*** Remove bit and collet.
*** Place both collet wrenches on top of electronics box
*** clean up work area
*** Smooth out waste board if you puckered it at all.
*** Check if the dust collector needs to be emptied

** Post a picture on our [[Blog]] please!

== Use checklist ==

PS1 is experimenting with the use of checklists to encourage the safe use and proper care of tools in the workspace. The latest version of the [[checklists]] for this tool is stored as a [https://docs.google.com/document/d/1zxrvQX0DXaLxaXkaKCKpZ-PAgnDak6ezKKBkdu_Fw1U/edit?usp=sharing Google Doc] that can be edited by anyone. If you make changes, update the effective date at the bottom of the document. Print a new copy, and replace the old one.

Physical checklists are necessarily constrained in length. Following is a more extensive pre-flight checklist:

* Did you home the machine?
* Is the dust collect gate open?
* Are you sure you have the right X, Y orientation for your file and material?
* Did you set the proper X,Y zero for your work piece on the Shopbot.
* Is the correct bit installed and tight?
* Is the key in and turned on?
* Is the dust skirt set right so it does not get smashed.
* Is Z zero set to the work top?
* Are the touch plate and clip returned?
* Is the material properly secured?
* Open the Shopbot spindle control dialog (Tools > Spindle RPM Control)
* Safety glasses, hearing protection on.
* Start the job with the E-Stop ready to hit.
* Turn on dust collector ( I like to wait so I can hear that things sound right on the shopbot before turning on the collector)

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Elizabeth Koprucki
|Danger Committee
|
|-
|Bart Dring
|Danger Committee
|
|-
|Ryan Pierce
|Danger Committee
|
|-
|Nathan Ellis
|Danger Committee
|
|-
|Michael Skilton
|Danger Committee
|
|-
|Arturo Duarte
|Bart
|
|-
|Derek Bever
|Bart
|
|-
|Everett
|Bart
|
|-
|Vincent Colombo
|Bart
|
|-
|[[User:justin|Justin T. Conroy]]
|Bart
|
|-
|Hugh Sato
|Bart
|
|-
|Sergey Nekrasov
|Bart
|
|-
|Valerie Moore
|Bart
|
|-
|Patrick Schless
|Bart
|
|-
|Tom Forajter
|Bart
|
|-
|Todd Allen
|Michael Skilton
|
|-
|[[User:RogerMoore|Roger Moore]]
|Bart
|
|-
|Tim Saylor
|Bart
|
|-
|Hef
|Bart
|
|-
|Jeff McBride
|Bart
|
|-
| Maxwell ?
| Michael Skilton
|
|-
|Samuel Swope
|Michael Skilton
|
|-
| Khoi Nguyen
|Michael Skilton
|
|-
|Brian Chojnowski
|Michael Skilton
|
|-
|Josh Cooper
|Bart
|
|-
|Andrew Camardella
|Bart
|
|-
|Adam Glick
|Bart
|
|-
|Yehuda Braun
|Bart
|
|-
| Jeff Kantarek
| Michael Sklton
|
|-
| Justin Miles
|Michael Skilton
|
|-
|Will Garza
|Michael Skilton
|
|-
|Clarence Risher
|Michael Skilton
|
|-
|[[User:ericbeau|Eric Beauchamp]]
|Michael Skilton
|
|-
|[[User:Jason|Jason]]
|Michael Skilton
|
|-
|Eric Stein
|Bart
|
|-
|Colin Parsons
|Bart
|
|-
|David Ditzler
|Bart
|
|-
|Ray Doeksen
|Bart Dring
|
|-
|Ron Bean
|Khoi Nguyen & Michael Skilton
|
|-
| Thomas Wright
|Khoi Nguyen & Michael Skilton
|
|-
|David Morton
|Bart Dring
|
|-
|Ron Olson
|Bart Dring
|
|-
|Kyle Bieneman
|Bart Dring
|
|-
|[[User:amishhammer|Tom Judge]]
|Michael Skilton
|
|-
|Bryan Gleason
|Michael Skilton
|
|-
|Dave Schact
|Ryan Pierce
|
|-
|Chris Agocs
|Andrew Camardella
|
|-
|[[user:kuroishi | Doorman Dave ]]
|Andrew Camardella
|
|-
|Alec Weege
|Andrew Camardella
|
|-
|Sam Reicks
|Andrew Camardella
|
|-
|Touly Phiachantharath
|Andrew Camardella
|
|-
|Lucas Goossen
|Andrew Camardella
|
|-
|[[user:Tina|Tina C]]
|Andrew Camardella
|
|-
|Ryan Neuman
|Andrew Camardella
|
|-
|Dan Loeser
|Andrew Camardella
|
|-
|Ben Bogler
|Andrew Camardella
|
|-
|Erin Banwell
|Ryan Pierce
|
|-
|Brad Rios
|Ryan Pierce
|
|-
|Aaron Carlock
|Andrew Camardella
|
|-
|James Villalpando
|Andrew Camardella
|
|-
|Connor Jansen
|Andrew Camardella
|
|-
|Tait Leswing
|Bart
|
|-
|Raj Perera
|Khoi Nguyen
|
|-
|Keith Hultman
|Andrew Camardella
|
|-
|David Srebro
|Andrew Camardella
|
|-
|[[user:Wessing | Erik Wessing ]]
|Andrew Camardella
|
|-
|Leeswann Bolden
|Andrew Camardella
|
|-
|Josh Myers
|Andrew Camardella
|
|-
|Kurt Ziegel
|Andrew Camardella
|
|-
|Glenn Powers
|Andrew Camardella
|
|-
|[[User:mqudsi|Mahmoud Al-Qudsi]]
|Andrew Camardella
|
|-
|Casey Olson
|Khoi
|
|-
|Mike Jones
|Andrew Camardella
|
|-
|Aaron Feigen
|Andrew Camardella
|
|-
|Jim Baker
|Andrew Camardella
|
|-
|Eric Reusche
|Khoi Nguyen
|
|-
|Ralph Brendler
|Andrew Camardella
|
|-
|John McDonald
|Andrew Camardella
|
|-
|Alex Al-Hamdan
|Andrew Camardella
|
|-
|Eugene Liokumovich
|Andrew Camardella
|
|-
|Randal Cox
|Andrew Camardella
|
|-
|Simon Pyle
|Andrew Camardella
|
|-
|Jean Michel Crettaz
|Andrew Camardella
|
|-
|Brian Zable
|Andrew Camardella
|
|-
|Daylan Dufelmeier
|Andrew Camardella
|
|-
|Steve Kruse
|Matt Meshulam
|
|-
|Mike Mandrea
|Andrew Camardella
|
|-
|Jeff Zelnio
|Andrew Camardella
|
|-
|Aaron Stoddart
|Matt Meshulam
|
|-
|Koun Park
|Matt Meshulam
|
|-
|Dan Baltudis
|Matt Meshulam
|
|-
|Curtiss Cooke
|Matt Meshulam
|
|-
|Jeannine Chuchan
|Matt Meshulam
|
|-
|Brennan Koziarz
|Matt Meshulam
|
|-
|Brandon Love
|Matt Meshulam
|
|-
|Mike Vitale
|Matt Meshulam
|
|-
|Emma Purola
|Matt Meshulam
|
|-
|Chris Kohl
|Matt Meshulam
|
|-
|Daniel Sojka
|Matt Meshulam
|
|-
|Naguib Azab
|Matt Meshulam
|
|-
|Mark Zumwalt
|Matt Meshulam
|
|-
|Joseph Juhnke
|Andrew Camardella
|
|-
|Alex Berkowitz
|Andrew Camardella
|
|-
|Andy Muhic
|Matt Meshulam
|
|-
|Adam Stein
|Matt Meshulam
|
|-
|John Farmer
|Matt Meshulam
|
|-
|Joshua Havenga
|Matt Meshulam
|
|-
|[[user:mct|McTavish McArdle]]
|Matt Meshulam
|
|-
|Frank Bowles
|Matt Meshulam
|
|-
|Joe Iklov
|Matt Meshulam
|
|-
|Matthew Quigley
|Matt Meshulam
|
|-
|Derwin Umali
|Andrew Camardella
|
|-
|Doug Mahoney
|Matt Meshulam
|
|-
|Rob Robinson
|Matt Meshulam
|
|-
|Dan Sloboda
|Matt Meshulam
|
|-
|Jacob Collins
|Matt Meshulam
|
|-
|Donald Wells
|Matt Meshulam
|
|-
|[[user:jim|Jim Brink]]
|Matt Meshulam
|
|-
|[[user:mkeith|Matt Keith]]
|Matt Meshulam
|
|-
|[[user:vmorris|Victoria Morris]]
|Matt Meshulam
|
|-
|[[user:bobsabayesian|Bob Loos]]
|Matt Meshulam
|
|-
|[[user:muthpete|Peter Muth]]
|Matt Meshulam
|
|-
|[[user:guijemont|Guillaume Emont]]
|Matt Meshulam
|
|-
|[[user:erikthefunk|Erik Funkhouser]]
|Matt Meshulam
|
|-
|[[user:mrashes|Max Rashes]]
|Matt Meshulam
|
|-
|[[user:panchan99|Juan Ramos]]
|Matt Meshulam
|
|-
|[[user:Justjoe|Joe Dowling]]
|Matt Meshulam
|
|-
|[[user:smash|Ashley Matrisciano]]
|Matt Meshulam
|
|-
|Ryan Kapp
|Matt Meshulam
|
|-
|Idris Raja
|Matt Meshulam
|
|-
|[[user:Dannyblanchard|Danny Blanchard]]
|Matt Meshulam
|
|-
|Aaron Mintz
|Matt Meshulam
|
|-
|[[user:ianstubbs|Ian Stubbs]]
|Matt Meshulam
|
|-
|[[user:skynaya|Sky Nova]]
|Matt Meshulam
|
|-
|Chris Ruhland
|Matt Meshulam
|
|-
|[[user:Jaypee|Jay Pee]]
|Matt Meshulam
|
|-
|[[user:Ryanmafi|Ryan Fiebing]]
|Matt Meshulam
|
|-
|[[user:sblaszak|Shawn Blaszak]]
|Matt Meshulam
|
|-
|[[user:tonyiacullo|Tony Iacullo]]
|Matt Meshulam
|
|-
|Mark Haughey
|Matt Meshulam
|
|-
|Chris Iacullo
|Matt Meshulam
|
|-
|Ian Monroe
|Matt Meshulam
|
|-
|Ashish Jasani
|Matt Meshulam
|
|-
|Kurt Gilman
|Matt Meshulam
|
|-
|Abel Greenwald
|Matt Meshulam
|
|-
|Vaidotas (Vai) Staugaitis
|Matt Meshulam
|
|-
|Leo Battikhi
|Matt Meshulam
|
|-
|Matt Schaid
|Matt Meshulam
|
|-
|Jamie Vollmer
|Matt Meshulam
|
|-
|Bhairavi Warke
|Matt Meshulam
|
|-
|Denis Kuznetsov
|Matt Meshulam
|
|-
|Brian Carstensen
|Matt Meshulam
|
|-
|Rob Dumas
|Matt Meshulam
|
|-
|Mark Weiser
|Matt Meshulam
|
|-
|Tom Burtonwood
|Matt Meshulam
|
|-
|Steve Madonna
|Matt Meshulam
|
|-
|Jason Araujo
|Matt Meshulam
|
|-
|Bruce Alan Mace
|Matt Meshulam
|
|-
|Molly Adamski
|Matt Meshulam
|
|-
|Jeremy Shaw
|Matt Meshulam
|
|-
|Sam Chen
|Matt Meshulam
|
|-
|John McBride
|Matt Meshulam
|
|-
|Adomas Tautkus
|Matt Meshulam
|
|-
|Tim Buckley
|Matt Meshulam
|
|-
|Martina Josimovska
|Matt Meshulam
|
|-
|James Jacobs
|Matt Meshulam
|
|-
|George Shaw
|Matt Meshulam
|
|-
|David Earl
|Matt Meshulam
|
|-
|[[User:pedrosk| Eduard Breuer]]
|Matt Meshulam
|
|-|-
|Matthew Kim
|Matt Meshulam
|
|-
|Corey Peoples
|Matt Meshulam
|
|-
|Paul Graham
|Matt Meshulam
|
|-
|Matt Grunstad
|Matt Meshulam
|
|-
|Rolf Scheidt
|Matt Meshulam
|
|-
|Arjun Sharma
|Matt Meshulam
|
|-
|Chris Laurent
|Matt Meshulam
|
|-
|[[User:dwlocks|Dan Locks]]
|Matt Meshulam
|
|-
|Zack Sasnow
|Matt Meshulam
|
|-
|Ben Stringer
|Matt Meshulam
|
|-
|[[User:Ekaj|Jacob Snyder]]
|Matt Meshulam
|8/24/17
|-
|James Beck
|Matt Meshulam
|9/13/17
|-
| Sam Gates
|Matt Meshulam
|10/01/17
|-
| Tommy TBones Cramer
|Matt Meshulam
|09/24/17
|-
| tee
|Matt Meshulam
|10/26/17
|-
|[[User:wittnl|Nathan Witt]]
|Matt Meshulam
|2017-12-09
|-
|[[User:GalaxyCascade|Steve Griegoliet]]
|Matt Meshulam
|12/09/17
|-
| Chinbayar Davaatseren
| Matt Meshulam
| 12/09/17
|-
|Theo T
|David Earl
|1/20/18
|-
|[[User:Frenchy|Jeremie Davis]]
|David Earl
|1/21/18
|-
|Armani Barron
|Matt Meshulam
|9/16/17
|-
|Scott Fullman
|David Earl
|02/24/18
|-
|Michael Donovan
|David Earl
|03/04/2018
|-
|Damon Carrvesco
|David Earl
|03/26/2018
|-
|Ryan Kelly
|David Earl
|03/26/2018
|-
|Will Coffin
|David Earl
|03/26/2018
|-
|Shabab Mustafa
|David Earl
|03/26/2018
|-
|Bruce Mace
|David Earl
|03/26/2018
|-
|Shahnawas Khokhar
|David Earl
|03/26/2018
|-
|Seth Cothron
|David Earl
|04/22/2018
|-
|Matthew Currey
|David Earl
|04/22/2018
|-
|Adam Hall
|David Earl
|04/29/2018
|-
|Kevin Huemann
|David Earl
|04/29/2018
|-
|Donzell Gordon
|David Earl
|04/28/2018
|-
|Nelson Reyes
|David Earl
|05/26/2018
|-
|David DesRoberts
|David Earl
|05/26/2018
|-
|Brendan Fortune
|David Earl
|06/02/2018
|-
|Chris Albert
|David Earl
|06/17/2018
|-
|Nate Myren
|David Earl
|06/23/2018
|-
|Eli Scholssberg
|David Earl
|06/23/2018
|-
|Szymon Mirek
|David Earl
|06/24/2018
|-
|Dan Willmott
|David Earl
|06/24/2018
|-
|Mark Treiber
|David Earl
|10/28/2018
|-
|Charlie Kepner
|David Earl
|02/20/2019
|-
|Kevin Cluff
|David Earl
|02/20/2019
|-
|Greg Bell
|David Earl
|03/23/19
|-
|Paul Ocampo
|David Earl
|03/28/19
|-
|Fritz Sullivan
|David Earl
|03/31/19
|-
|Daniel Gulick
|David Earl
|12/10/2018
|-
|Alex Biardo
|David Earl
|05/07/2019
|-
|Brendan Byrne
|David Earl
|05/07/2019
|-
|Sam Vuchetich
|David Earl
|09/29/2019
|-
|Antina Lee
|David Earl
|09/29/2019
|-
|Rob German
|David Earl
|09/29/2019
|-
|Ryan Zoghlin
|David Earl
|01/25/2020
|-}

If you have been authorized but cannot log in, request to be added to the "ShopBot Authorized" Samba group (send an email to info (at) pumpingstationone.org with your username and the name of the person who certified you) so that your login works. If you don't have a log-in on https://members.pumpingstationone.org/ you will have issues here - sign up on that site first if you haven't already.

= Maintenance =

== Maintenance Log ==
{| class="wikitable" border="1"
!Date
!Preformed by
!Service Type
!Notes
|-
|4/16/2017
|Ryan Pierce
|Created new AutoDesk Fusion 360 Post Processor. Modified Vectric Post Processors.
|Created new Fusion 360 Post Processor. It includes the changes listed below for the Vectric Post Processors. For Vectric, modified the Post Processors so that if the spindle does not spin up, it gives the user a Retry/Cancel dialog box instead of Abort/Retry/Ignore where Ignore is identical to Retry. Also, these Post Processors broke the Preview mode in the ShopBot software because the preview mode did the real spindle check and it failed because, of course, the spindle wasn't running. The new version will ignore the spindle check in preview mode.
|-
|11/8/2014
|Ryan Pierce
|Updated VCarve Post Processor
|Previously, installed new Post Processor to preset an Abort / Retry / Ignore dialog box when the spindle is started but doesn't spin up. Usual culprit is that a job is started when the the interlock is disabled, which results in the non-spinning bit crashing into the workpiece. Abort stops the job. Today, fixed Retry code. If you power on the VFD and the motor start is enabled, the VFD refuses to start. So I've re-programmed the Retry button to stop the VFD, wait 2 seconds, start the VFD, wait 2 more seconds, and check again to see if it is running. The Ignore button actually acts as Retry because we don't want someone clicking through this dialog box and damaging the machine. NOTE: The Aspire PC in the shop also has this Post Processor, but if you use Aspire, VCarve Pro, etc. on your personal computer, you will need the latest Post Processor to support this safety check.
|-
|11/8/2014
|Ryan Pierce
|Updated ShopBot software
|Did upgrade from 3.8.14 to 3.8.26. Installed latest firmware on ShopBot controller. (This was mandatory.) Two features of interest: Fixed occasional erractic behavior after repeated Stops and Resumes (and Nudges or Command Insertions). Reduced liklihood of Keypad lockup.
|-
|5/31/2015
|Ron Olson
|Created new VCarve Post Processors
|For drag/engraving bits, it's important that the spindle be turned '''off''' so as to not destroy the bit. Instead of manually modifying the sbp every time to remove the check that the spindle is turned on, I created a couple of new post processors (inches and mm, similar to Ryan's), that explicitly ''turn off'' the spindle. The user is given two opportunities to cancel the job if that is not what he/she wants.
|-
|}

== Outstanding Maintenance Issues ==

=== Lack of True E-Stop ===
As shipped, the ShopBot PRS does not support an Emergency Stop. This could be hacked, but it runs the risk of damaging the machine if engaged in a non-emergency situation. Suggested solution: Installing a 10A double pole 24V coil DIN mount relay, and powering the coil via the 24V supply through a normally closed E-Stop button. One pole will disconnect the 63V stepper motor current. One pole will break the control signal that enables the VFD and will cause the VFD to brake to a stop.

=== Automatic Dust Collection ===
The ShopBot has +5V TTL outputs that could be used to trigger automatic dust collection (when the spindle goes live) and/or a warning light (when the gantry is enabled to move.)

=== Limit Switch Issues ===
Every time you start the ShopBot, it resets itself so that the limit switches are disabled! You can turn them on (if memory serves) with the Values -> Input Switch Assignment menu item. Limit switches are really useful - but they need to be enabled. When they are, they will stop manual jogging when the limit is hit (although pressing the key again will let you continue moving the gantry) and they will also stop a running job (but give you the option of ignoring the limits.)

I found a couple more problems when testing all the limits. When I took the gantry to X maximum, the dust collector hose pulled off! I put it back on, but I'm not sure how stable this is. Also, when I originally set the Y maximum and minimum, I wanted as much spindle travel as possible. But it appears that if you're at the Y max and move in the X direction, you can hit the middle support with the dust collector boot. We've got several inches Y travel beyond the nominal 48", so we may want to look into reducing this to clear the supports.

== Resources ==
[[File:ShopBot PSOne Post Processors.zip]] - Post Processors for Vectric Aspire and VCarve Pro 8.0 which includes the change to check that the spindle actually started.

[[File:ShopBot_TC_PS1-NO-SPIN.zip]] - Post Processors for Vectric Aspire and VCarve Pro which include changes to explicitly *disable* spinning

[[File:ShopBot PSOne Fusion 360 Post Processor.zip]] - Post Processor for Autodesk Fusion 360 which includes the change to check that the spindle actually started.

[[Category:Fabrication]]
[[Category:CNC]]
[[Category:Future Things Bus Data Sources]]

Shopbot PRS CNC router

2020-01-26T15:20:13Z

Rfoto:

{{Template:EquipmentPage
|owner = PS:One
|serial = TBD.
|certification = yes
|hackable = no
|model = Shopbot PRS #10108 96-48
|arrived = 2014
|image = Shopbot.jpg
|doesitwork = yes
|contact = [[CNC|CNC Area Host]]
|where = Wood Shop
|value = $16000
|hostarea = CNC
}}
= ShopBot PRS #10108 96-48 =

* [http://www.shopbottools.com/mProducts/prSstandard.htm OEM website and specs]
* Nominal Cutting Area 96"x 48"x 6" (2.44m x 1.22m x .15m)
* Total Movement Area 102" x 50" x 8" (2.59m x 1.27m x .20m)
* Max spindle speed: 18000 RPM
* Min spindle speed: 4100 RPM

The spindle uses ER25 collets. These eventually wear out, so check before using them. Collets are a durable expendable.

Some people buy their own collets. There are a number of suppliers of collets, nuts, and related accessories. [http://www.techniksusa.com/ Techniks] and [http://www.shars.com/ Shars] are both brands that have been recommended by experienced CNC users, although other brands may also be of equivalent price and quality:

* [http://www.shars.com/1-4-ultra-precision-5-micron-er25-collet Shars ER25 Collet Ultra Precision 5 Micron]
* [https://www.ebay.com/itm/TECHNIKS-1-4-SUPER-PRECISION-ER25-COLLET-0002-ACCURACY-CNC-CHUCK-MILL-/130701349603?hash=item1e6e6852e3 Techniks 1/4" Super Precision ER25 Collet .0002 Accuracy]
* [https://www.toolstoday.com/cnc-high-precision-spring-collets-for-er25-tool-holder.html?variantids=11644,0&keywords=CO-286 Amana CNC High Precision Spring Collets for ER25 Tool Holder]
* [https://www.amazon.com/HHIP-3900-5215-ER-25-Spring-Collet/dp/B01ABWS9IG/ HHIP 3900-5215 ER-25 Spring Collet, 1/4"]
* [https://www.amazon.com/Dorian-Tool-Alloy-Precision-Collet/dp/B00CB14HXW/ Dorian Tool ER25 Alloy Steel Ultra Precision Collet, 0.236" - 0.276" Hole Size]

=Status=
August 2017: Dust collection system out of commission.

June 2017: There is an intermittent break in the wiring for the Z-axis Zero Plate. Check for continuity before using (the #1 input should light up on screen when you touch the contacts together). It usually works near the front of the table, but not halfway back. This will get fixed eventually, but it's a good idea to be in the habit of checking.

12/27/16 - Fixed Shopbot x-axis homing. The cable had been pulled on hard enough that some of the conductors broke inside the cable. It has been spliced, soldered, and heatshrinked back together.

= How to Get Authorized =

'''Authorization for this tool by authorized proctors only.''' This means you cannot get authorized by just anyone who is already authorized. You can only get authorized by a few people, the proctors listed below.

Authorization sessions are scheduled roughly monthly. Check the [https://www.meetup.com/Pumping-Station-One/events/ Meetup calendar] for upcoming authorizations. If no ShopBot sessions are currently scheduled, ask the [[CNC Area Host]] or on the [https://groups.google.com/group/pumping-station-one/ Google Group].

Be aware that this authorization consists of two parts; the first session is a classroom session that will cover the software required and introduce you to the essential settings and chip-load calculation, and the second part, scheduled separately, is a hands-on class.

== Authorizers ==
{| class="wikitable" border="1"
|-
|Elizabeth Koprucki
|Danger Committee
|-
|Bart Dring
|Danger Committee
|-
|Ryan Pierce
|Danger Committee
|-
|Nathan Ellis
|Danger Committee
|-
|Michael Skilton
|Danger Committee
|-
|Khoi Nguyen
|Michael Skilton
|-
|Andrew Camardella
|Elizabeth Koprucki
|-
|Matt Meshulam
|Andrew Camardella
|-
|David Earl
|Matt Meshulam
|-
|}

== How to Become an Authorizer ==
Get an ok from the area host. Successfully run an authorization supervised by an authorizer.
It's recommended that initial authorizations be limited to 2 member participants or less.

= Documentation =

[[File:Shopbotassembly.pdf|Shopbotassembly.pdf]]

[[File:Squaringshopbot.pdf|Squaring the ShopBot]]

[[File:Programming_handbook.pdf|Programming Handbook]]

[[File:PRS Maintenance Schedule.pdf|Maintenance Schedule]]

[[File:ShopBot_USB_Connection_Troubleshoot.pdf]] - USB Troubleshooting Guide

[[File:ShopBot_Tech_Support_FAQ_2016_09_12.pdf]] - Tech Support FAQ

[[File:SBG00142 User Guide 2013 05 01.pdf|SBG00142 User Guide 2013 05 01.pdf]] - User Guide

[[File:B17P.763_Schematic.pdf]] - Omer Nail Gun Documentation

[http://www.shopbottools.com/ShopBotDocs/files/quick%20start%20guide%202013%2007%2023.pdf QuickStart]

X, Y, Z probe: https://pumpingstationone.org/2015/09/xyz-finder-for-the-shopbot/

[http://drshopbot.com/index.php?title=Main_Page "Dr Shopbot" wiki]

[http://drshopbot.com/index.php?title=MaintainingConnection "Maintaining Connections"]

[[File:Shopbotmagnets.ai.zip]] - Template for the dust skirt and magnet placement.

== Tutorials ==
[https://www.youtube.com/watch?v=xWCZfYHOYWw Part 1 of our Shopbot Authorization] - This is available as a refresher only. You still need to go to the class when it happens to get access to the hands-on Part 2.

[http://www.woodguide.org/files/2014/07/CNCrouter_bit_basics.pdf Router Bit Basics for CNC - VERY USEFUL]

[https://groups.google.com/forum/?fromgroups=#!searchin/pumping-station-one/shopbot Shopbot Threads on Member List]

[https://groups.google.com/forum/?fromgroups=#!searchin/pumping-station-one/shopbot Shopbot Forum]

[https://groups.google.com/d/msg/pumping-station-one/vUF3iKRQ9yc/_qNnLXzZ3QcJ Overview of Cut Load calcualtions for setting bit feed and speed rates]

Vertanux1: This user teaches at Elgin Community College and has very good tutorials and downloadable textbook on Autodesk Inventor (which applies to Fusion 360 as well: http://www.vertanux1.com/ and https://www.youtube.com/user/vertanux1?reload=9

Online chipload calculator: https://www.guhdo.com/chipload-calculator

Fusion 360 Videos

NYC CNC - Several videos that provide an overview of downloading software, preferences, and basic sketch terms and steps. https://www.nyccnc.com/fusion-360/

Lars Christensen - CAD/CAM instructor hired by Autodesk to produce their Fusion 360 videos. The Absolute Basics and #LarsLive series are worth watching. https://www.youtube.com/watch?v=A5bc9c3S12g&feature=youtu.be

Maker's Muse CAD for Newbies Series - Provides a detailed overview of sketch dimensions, constraints, revolving, sweeping, and lofting, among many other topics. https://www.youtube.com/playlist?list=PLTCCNNvHC8PC40tcEqaJcgUMb97LNkLIn

Krenov Coffee Table - A fantastic overview of the design of a coffee table from scratch. Lots of CAD best practices. https://www.youtube.com/watch?v=J22j8RfETjs&feature=youtu.be

Fusion 360 V12 Engine - A long playlist series on a complex topic that demonstrates how powerful real CAD software can be. https://www.youtube.com/playlist?list=PLQl9vsO6sGSlasKFP-CAgnDs324Z6IW8s

= Software Tool Chain =
*Illustrator
*Inkscape
*Vectric Aspire
**Allows for 2D and 3D linework and toolpath creation
**Only available on the Shapeoko Computer
*Vectric V-Carve Makerspace Edition Version 9.0 (earlier versions may not be supported here anymore)
** http://www.vectric.com/products/vcarve/trial.html
**Allows for 2D linework and toolpath creation
**Allows at home use of V-Carve - output only at PS1
**Our Makerspace Code is: E4793-F6472-BB9E5-9B114-3FEEB-73649-16F4F
*Autodesk Fusion 360
**The ShopBot computer does not have this and may not be fast enough to run it.
**You '''MUST''' use the custom post-processor below. Otherwise, you will bypass the safety check to make sure the spindle really is running!
**For local '''Windows''', to install this on your local computer:
***Unzip and install this in C:\Users\YourName\AppData\Roaming\Autodesk\Fusion 360 CAM\Posts
***Note that AppData is often a hidden folder!
***Inside Fusion 360, when you select Actions / Post Process, under Configuration Folder, hit Setup and select Use Personal Posts.
**For local '''Mac'''
*** Unzip and install in Macintosh HD> Users> USERNAME> Autodesk> Fusion 360 CAM> Posts
*** In Fusion 360, when you select Actions > Post Process, under Settings select Personal Posts for the Source
**For '''Cloud'''
*** Open Fusion 360 and navigate to Libraries > Assets in the Data Panel.
*** Double click the Assets > CAMPosts folder to enter it.
*** Use the Upload button to upload the desired post processor from your local machine to the Assets > CAMPosts folder. This will upload the post to the cloud and allow you to access it anywhere you may login to your Fusion 360 account through My Cloud Posts.
*** After enabling cloud libraries in Fusion 360, you will be able to access your cloud post processor library by setting the Configuration Folder (Windows) or Source (Mac) to My Cloud Posts. Both of these dialog boxes are shown below. You will then be able to select the Cloud post you uploaded in the Post Configuration field (Windows) or the Post Processor field (Mac).
====Chip Load Calculation====
*[https://www.guhdo.com/chipload-calculator Chip Load Calculator by Guhdo]
*[http://www.pdsspindles.com/engineering-speeds Bit Parameter Overview by PDS Spindles]
*[https://www.monstertool.com/29/tech-data.htm Monster Tools Chip Load Calculator]
*[http://www.pdsspindles.com/admin/modules/page_editor/uploads/image/Chip%20load%20for%20common%20tool%20diameters%20(Inches).jpg Chip Load Chart by PDS Spindles]
*[https://groups.google.com/forum/#!searchin/pumping-station-one/makerspace$20edition/pumping-station-one/cTwfUHxESjU/7m_lI8UWCgAJ How to install Makerspace Version]

== User Tips & Troubleshooting Reports ==
[http://www.sgstool.com/PDF-speedfeeds/SGS-Speeds-Feeds-GP.pdf Some feed and speed recommendations for small bits]

Add your experiences with feeds and speeds or other tips here:
[[Shopbot_User_Tips]]

Add troubleshooting reports here:
[[Shopbot_Troubleshooting_Reports]]

=== Materials ===

* [[Shopbot_PRS_CNC_router/Aluminium|Aluminium]]
* [[Shopbot_PRS_CNC_router/Brass|Brass]]
* [[Shopbot_PRS_CNC_router/Wood|Wood]]

== Authorization Checklist ==

This is here as a checklist for proctors to follow when authorizing people. It can also help remind you of things after you are authorized. Just reading this does not authorizing you.

* How to get authorized
** Watch [http://www.meetup.com/Pumping-Station-One/ the meetup group] for a recurring class on the second Thursday and last Sunday of the month. Sometimes check [https://groups.google.com/forum/#!forum/pumping-station-one the forum] for announcements or ask on the forum if no announcements have been made for a few weeks.

* Authorization group size
** There is no cap to the software instruction preceding the machine usage portion of the class. If you come to this portion it is easier to get fully authorized at a later date.
** 3 machine users - each person will run a job (~1/2 hr each) and everyone will assist each other in completing a job profile and pocket cut. You must be present for the entire authorization

* Safety
** Safety Glasses
** Hearing Protection
** Dust Protection

* What can go wrong (and what to do)

* How does machine work
** Axes
** Motors
** Spindle

* Daily Maintenance
** Spindle bearing warm up.
*** The "C5" warm up routine should be run on the first job of the day. It runs the spindle at 3 speeds for 3 minutes each to warm up the bearings. (When it doubt, warm it up)

* Extended Maintenance
** See maintenance schedule file under documentation.
** Grease the racks
** Use Grease type: Manual states any type is safe there is some in the draw

* Machine Control
** Turn on sequence
*** Log into computer
*** Turn on Shopbot big red and yellow twist switch (see zeroing below)
*** Insert Key and turn to "engaged" position.
*** The VDF should light up, the spindle fan should be on.
*** Start "Shopbot 3" program.
*** Open Tools...Spindle RPM Control menu (to allow RPM control)
**** Make sure collet is tightened or no tool or nut is installed
**** Run the C5 warm up routine
** Jogging
*** Keypad
*** Arrow Keys + Page Up, Page Down (ctrl for fast jog)

* CAM Software
** Vectric V Carve
** Just the basics...separate class for advanced V Carve.
** Online videos

* Running your Job
** Zeroing X & Y
*** With machine off slow push gantry towards X0 until it hits hard stops (optional)
*** Turn on big red switch while still holding gantry.
*** Jog machine away from X0 Y0 so machine will find switches
*** Click X, Y zero button.
** Zeroing Z (top of work piece)
*** Jog over your work piece
*** Place Z zero plate on work piece under the bit
*** Place clip on bit
*** Test connection by touching plate to bit and watch for light #1 to light
*** Click the Z 0 button (it will touch off twice!!!)
*** If Z is critical, you may want to verify that your bit has been zeroed properly by using a "MZ,0" command over the surface you have zeroed the bit to. Repeat zeroing if not correct.

* Waste Board and clamping

* Collets, Bits, Feeds and Speeds
** Feeds and Speeds
*** Use a Cut Load Calculator to determine which feeds and speeds you should be using for your specific bits. An overview is avaialble at: [https://groups.google.com/d/msg/pumping-station-one/vUF3iKRQ9yc/_qNnLXzZ3QcJ]
** Collets
*** We currently have collets for 1/2, 1/4, 3/16 and 1/8" shank bits.
*** Try to keep them clean and store them away from dust between uses. Dust between the gaps will produce runout. The drawer mounted under the Shopbot is the right place to store these items.
*** If the collet nuts are not threading smoothly try cleaning the threads with a small brush, spindle threads as well.
** Bits
*** Use bits designed for the material you are cutting. Don't just steal a bits from the Bridgeport. They won't do a good job and will probably overheat.
*** For cutting out things, use the smallest appropriate bit. Using a 1/2" bit to cutout will just create a lot of mess.

* ShopBot should not be used for...
** Metals other than aluminum
** Cutting anything that requires coolant or lubricant (it will ruin the waste board)
** Ripping lumber (use the table saw)
** Thickness Planning (Use the planner if you can)
** Drilling holes with drill bits (a small end mill works better)

* How to leave the machine (be excellent)
** Machine
*** Home the machine to X0, Y0
*** Turn off both switches
*** Remove Key
*** Remove bit and collet.
*** Place both collet wrenches on top of electronics box
*** clean up work area
*** Smooth out waste board if you puckered it at all.
*** Check if the dust collector needs to be emptied

** Post a picture on our [[Blog]] please!

== Use checklist ==

PS1 is experimenting with the use of checklists to encourage the safe use and proper care of tools in the workspace. The latest version of the [[checklists]] for this tool is stored as a [https://docs.google.com/document/d/1zxrvQX0DXaLxaXkaKCKpZ-PAgnDak6ezKKBkdu_Fw1U/edit?usp=sharing Google Doc] that can be edited by anyone. If you make changes, update the effective date at the bottom of the document. Print a new copy, and replace the old one.

Physical checklists are necessarily constrained in length. Following is a more extensive pre-flight checklist:

* Did you home the machine?
* Is the dust collect gate open?
* Are you sure you have the right X, Y orientation for your file and material?
* Did you set the proper X,Y zero for your work piece on the Shopbot.
* Is the correct bit installed and tight?
* Is the key in and turned on?
* Is the dust skirt set right so it does not get smashed.
* Is Z zero set to the work top?
* Are the touch plate and clip returned?
* Is the material properly secured?
* Open the Shopbot spindle control dialog (Tools > Spindle RPM Control)
* Safety glasses, hearing protection on.
* Start the job with the E-Stop ready to hit.
* Turn on dust collector ( I like to wait so I can hear that things sound right on the shopbot before turning on the collector)

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Elizabeth Koprucki
|Danger Committee
|
|-
|Bart Dring
|Danger Committee
|
|-
|Ryan Pierce
|Danger Committee
|
|-
|Nathan Ellis
|Danger Committee
|
|-
|Michael Skilton
|Danger Committee
|
|-
|Arturo Duarte
|Bart
|
|-
|Derek Bever
|Bart
|
|-
|Everett
|Bart
|
|-
|Vincent Colombo
|Bart
|
|-
|[[User:justin|Justin T. Conroy]]
|Bart
|
|-
|Hugh Sato
|Bart
|
|-
|Sergey Nekrasov
|Bart
|
|-
|Valerie Moore
|Bart
|
|-
|Patrick Schless
|Bart
|
|-
|Tom Forajter
|Bart
|
|-
|Todd Allen
|Michael Skilton
|
|-
|[[User:RogerMoore|Roger Moore]]
|Bart
|
|-
|Tim Saylor
|Bart
|
|-
|Hef
|Bart
|
|-
|Jeff McBride
|Bart
|
|-
| Maxwell ?
| Michael Skilton
|
|-
|Samuel Swope
|Michael Skilton
|
|-
| Khoi Nguyen
|Michael Skilton
|
|-
|Brian Chojnowski
|Michael Skilton
|
|-
|Josh Cooper
|Bart
|
|-
|Andrew Camardella
|Bart
|
|-
|Adam Glick
|Bart
|
|-
|Yehuda Braun
|Bart
|
|-
| Jeff Kantarek
| Michael Sklton
|
|-
| Justin Miles
|Michael Skilton
|
|-
|Will Garza
|Michael Skilton
|
|-
|Clarence Risher
|Michael Skilton
|
|-
|[[User:ericbeau|Eric Beauchamp]]
|Michael Skilton
|
|-
|[[User:Jason|Jason]]
|Michael Skilton
|
|-
|Eric Stein
|Bart
|
|-
|Colin Parsons
|Bart
|
|-
|David Ditzler
|Bart
|
|-
|Ray Doeksen
|Bart Dring
|
|-
|Ron Bean
|Khoi Nguyen & Michael Skilton
|
|-
| Thomas Wright
|Khoi Nguyen & Michael Skilton
|
|-
|David Morton
|Bart Dring
|
|-
|Ron Olson
|Bart Dring
|
|-
|Kyle Bieneman
|Bart Dring
|
|-
|[[User:amishhammer|Tom Judge]]
|Michael Skilton
|
|-
|Bryan Gleason
|Michael Skilton
|
|-
|Dave Schact
|Ryan Pierce
|
|-
|Chris Agocs
|Andrew Camardella
|
|-
|[[user:kuroishi | Doorman Dave ]]
|Andrew Camardella
|
|-
|Alec Weege
|Andrew Camardella
|
|-
|Sam Reicks
|Andrew Camardella
|
|-
|Touly Phiachantharath
|Andrew Camardella
|
|-
|Lucas Goossen
|Andrew Camardella
|
|-
|[[user:Tina|Tina C]]
|Andrew Camardella
|
|-
|Ryan Neuman
|Andrew Camardella
|
|-
|Dan Loeser
|Andrew Camardella
|
|-
|Ben Bogler
|Andrew Camardella
|
|-
|Erin Banwell
|Ryan Pierce
|
|-
|Brad Rios
|Ryan Pierce
|
|-
|Aaron Carlock
|Andrew Camardella
|
|-
|James Villalpando
|Andrew Camardella
|
|-
|Connor Jansen
|Andrew Camardella
|
|-
|Tait Leswing
|Bart
|
|-
|Raj Perera
|Khoi Nguyen
|
|-
|Keith Hultman
|Andrew Camardella
|
|-
|David Srebro
|Andrew Camardella
|
|-
|[[user:Wessing | Erik Wessing ]]
|Andrew Camardella
|
|-
|Leeswann Bolden
|Andrew Camardella
|
|-
|Josh Myers
|Andrew Camardella
|
|-
|Kurt Ziegel
|Andrew Camardella
|
|-
|Glenn Powers
|Andrew Camardella
|
|-
|[[User:mqudsi|Mahmoud Al-Qudsi]]
|Andrew Camardella
|
|-
|Casey Olson
|Khoi
|
|-
|Mike Jones
|Andrew Camardella
|
|-
|Aaron Feigen
|Andrew Camardella
|
|-
|Jim Baker
|Andrew Camardella
|
|-
|Eric Reusche
|Khoi Nguyen
|
|-
|Ralph Brendler
|Andrew Camardella
|
|-
|John McDonald
|Andrew Camardella
|
|-
|Alex Al-Hamdan
|Andrew Camardella
|
|-
|Eugene Liokumovich
|Andrew Camardella
|
|-
|Randal Cox
|Andrew Camardella
|
|-
|Simon Pyle
|Andrew Camardella
|
|-
|Jean Michel Crettaz
|Andrew Camardella
|
|-
|Brian Zable
|Andrew Camardella
|
|-
|Daylan Dufelmeier
|Andrew Camardella
|
|-
|Steve Kruse
|Matt Meshulam
|
|-
|Mike Mandrea
|Andrew Camardella
|
|-
|Jeff Zelnio
|Andrew Camardella
|
|-
|Aaron Stoddart
|Matt Meshulam
|
|-
|Koun Park
|Matt Meshulam
|
|-
|Dan Baltudis
|Matt Meshulam
|
|-
|Curtiss Cooke
|Matt Meshulam
|
|-
|Jeannine Chuchan
|Matt Meshulam
|
|-
|Brennan Koziarz
|Matt Meshulam
|
|-
|Brandon Love
|Matt Meshulam
|
|-
|Mike Vitale
|Matt Meshulam
|
|-
|Emma Purola
|Matt Meshulam
|
|-
|Chris Kohl
|Matt Meshulam
|
|-
|Daniel Sojka
|Matt Meshulam
|
|-
|Naguib Azab
|Matt Meshulam
|
|-
|Mark Zumwalt
|Matt Meshulam
|
|-
|Joseph Juhnke
|Andrew Camardella
|
|-
|Alex Berkowitz
|Andrew Camardella
|
|-
|Andy Muhic
|Matt Meshulam
|
|-
|Adam Stein
|Matt Meshulam
|
|-
|John Farmer
|Matt Meshulam
|
|-
|Joshua Havenga
|Matt Meshulam
|
|-
|[[user:mct|McTavish McArdle]]
|Matt Meshulam
|
|-
|Frank Bowles
|Matt Meshulam
|
|-
|Joe Iklov
|Matt Meshulam
|
|-
|Matthew Quigley
|Matt Meshulam
|
|-
|Derwin Umali
|Andrew Camardella
|
|-
|Doug Mahoney
|Matt Meshulam
|
|-
|Rob Robinson
|Matt Meshulam
|
|-
|Dan Sloboda
|Matt Meshulam
|
|-
|Jacob Collins
|Matt Meshulam
|
|-
|Donald Wells
|Matt Meshulam
|
|-
|[[user:jim|Jim Brink]]
|Matt Meshulam
|
|-
|[[user:mkeith|Matt Keith]]
|Matt Meshulam
|
|-
|[[user:vmorris|Victoria Morris]]
|Matt Meshulam
|
|-
|[[user:bobsabayesian|Bob Loos]]
|Matt Meshulam
|
|-
|[[user:muthpete|Peter Muth]]
|Matt Meshulam
|
|-
|[[user:guijemont|Guillaume Emont]]
|Matt Meshulam
|
|-
|[[user:erikthefunk|Erik Funkhouser]]
|Matt Meshulam
|
|-
|[[user:mrashes|Max Rashes]]
|Matt Meshulam
|
|-
|[[user:panchan99|Juan Ramos]]
|Matt Meshulam
|
|-
|[[user:Justjoe|Joe Dowling]]
|Matt Meshulam
|
|-
|[[user:smash|Ashley Matrisciano]]
|Matt Meshulam
|
|-
|Ryan Kapp
|Matt Meshulam
|
|-
|Idris Raja
|Matt Meshulam
|
|-
|[[user:Dannyblanchard|Danny Blanchard]]
|Matt Meshulam
|
|-
|Aaron Mintz
|Matt Meshulam
|
|-
|[[user:ianstubbs|Ian Stubbs]]
|Matt Meshulam
|
|-
|[[user:skynaya|Sky Nova]]
|Matt Meshulam
|
|-
|Chris Ruhland
|Matt Meshulam
|
|-
|[[user:Jaypee|Jay Pee]]
|Matt Meshulam
|
|-
|[[user:Ryanmafi|Ryan Fiebing]]
|Matt Meshulam
|
|-
|[[user:sblaszak|Shawn Blaszak]]
|Matt Meshulam
|
|-
|[[user:tonyiacullo|Tony Iacullo]]
|Matt Meshulam
|
|-
|Mark Haughey
|Matt Meshulam
|
|-
|Chris Iacullo
|Matt Meshulam
|
|-
|Ian Monroe
|Matt Meshulam
|
|-
|Ashish Jasani
|Matt Meshulam
|
|-
|Kurt Gilman
|Matt Meshulam
|
|-
|Abel Greenwald
|Matt Meshulam
|
|-
|Vaidotas (Vai) Staugaitis
|Matt Meshulam
|
|-
|Leo Battikhi
|Matt Meshulam
|
|-
|Matt Schaid
|Matt Meshulam
|
|-
|Jamie Vollmer
|Matt Meshulam
|
|-
|Bhairavi Warke
|Matt Meshulam
|
|-
|Denis Kuznetsov
|Matt Meshulam
|
|-
|Brian Carstensen
|Matt Meshulam
|
|-
|Rob Dumas
|Matt Meshulam
|
|-
|Mark Weiser
|Matt Meshulam
|
|-
|Tom Burtonwood
|Matt Meshulam
|
|-
|Steve Madonna
|Matt Meshulam
|
|-
|Jason Araujo
|Matt Meshulam
|
|-
|Bruce Alan Mace
|Matt Meshulam
|
|-
|Molly Adamski
|Matt Meshulam
|
|-
|Jeremy Shaw
|Matt Meshulam
|
|-
|Sam Chen
|Matt Meshulam
|
|-
|John McBride
|Matt Meshulam
|
|-
|Adomas Tautkus
|Matt Meshulam
|
|-
|Tim Buckley
|Matt Meshulam
|
|-
|Martina Josimovska
|Matt Meshulam
|
|-
|James Jacobs
|Matt Meshulam
|
|-
|George Shaw
|Matt Meshulam
|
|-
|David Earl
|Matt Meshulam
|
|-
|[[User:pedrosk| Eduard Breuer]]
|Matt Meshulam
|
|-|-
|Matthew Kim
|Matt Meshulam
|
|-
|Corey Peoples
|Matt Meshulam
|
|-
|Paul Graham
|Matt Meshulam
|
|-
|Matt Grunstad
|Matt Meshulam
|
|-
|Rolf Scheidt
|Matt Meshulam
|
|-
|Arjun Sharma
|Matt Meshulam
|
|-
|Chris Laurent
|Matt Meshulam
|
|-
|[[User:dwlocks|Dan Locks]]
|Matt Meshulam
|
|-
|Zack Sasnow
|Matt Meshulam
|
|-
|Ben Stringer
|Matt Meshulam
|
|-
|[[User:Ekaj|Jacob Snyder]]
|Matt Meshulam
|8/24/17
|-
|James Beck
|Matt Meshulam
|9/13/17
|-
| Sam Gates
|Matt Meshulam
|10/01/17
|-
| Tommy TBones Cramer
|Matt Meshulam
|09/24/17
|-
| tee
|Matt Meshulam
|10/26/17
|-
|[[User:wittnl|Nathan Witt]]
|Matt Meshulam
|2017-12-09
|-
|[[User:GalaxyCascade|Steve Griegoliet]]
|Matt Meshulam
|12/09/17
|-
| Chinbayar Davaatseren
| Matt Meshulam
| 12/09/17
|-
|Theo T
|David Earl
|1/20/18
|-
|[[User:Frenchy|Jeremie Davis]]
|David Earl
|1/21/18
|-
|Armani Barron
|Matt Meshulam
|9/16/17
|-
|Scott Fullman
|David Earl
|02/24/18
|-
|Michael Donovan
|David Earl
|03/04/2018
|-
|Damon Carrvesco
|David Earl
|03/26/2018
|-
|Ryan Kelly
|David Earl
|03/26/2018
|-
|Will Coffin
|David Earl
|03/26/2018
|-
|Shabab Mustafa
|David Earl
|03/26/2018
|-
|Bruce Mace
|David Earl
|03/26/2018
|-
|Shahnawas Khokhar
|David Earl
|03/26/2018
|-
|Seth Cothron
|David Earl
|04/22/2018
|-
|Matthew Currey
|David Earl
|04/22/2018
|-
|Adam Hall
|David Earl
|04/29/2018
|-
|Kevin Huemann
|David Earl
|04/29/2018
|-
|Donzell Gordon
|David Earl
|04/28/2018
|-
|Nelson Reyes
|David Earl
|05/26/2018
|-
|David DesRoberts
|David Earl
|05/26/2018
|-
|Brendan Fortune
|David Earl
|06/02/2018
|-
|Chris Albert
|David Earl
|06/17/2018
|-
|Nate Myren
|David Earl
|06/23/2018
|-
|Eli Scholssberg
|David Earl
|06/23/2018
|-
|Szymon Mirek
|David Earl
|06/24/2018
|-
|Dan Willmott
|David Earl
|06/24/2018
|-
|Mark Treiber
|David Earl
|10/28/2018
|-
|Charlie Kepner
|David Earl
|02/20/2019
|-
|Kevin Cluff
|David Earl
|02/20/2019
|-
|Greg Bell
|David Earl
|03/23/19
|-
|Paul Ocampo
|David Earl
|03/28/19
|-
|Fritz Sullivan
|David Earl
|03/31/19
|-
|Daniel Gulick
|David Earl
|12/10/2018
|-
|Alex Biardo
|David Earl
|05/07/2019
|-
|Brendan Byrne
|David Earl
|05/07/2019
|-
|Sam Vuchetich
|David Earl
|09/29/2019
|-
-
|Antina Lee
|David Earl
|09/29/2019
-
|Rob German
|David Earl
|09/29/2019
|-}

If you have been authorized but cannot log in, request to be added to the "ShopBot Authorized" Samba group (send an email to info (at) pumpingstationone.org with your username and the name of the person who certified you) so that your login works. If you don't have a log-in on https://members.pumpingstationone.org/ you will have issues here - sign up on that site first if you haven't already.

= Maintenance =

== Maintenance Log ==
{| class="wikitable" border="1"
!Date
!Preformed by
!Service Type
!Notes
|-
|4/16/2017
|Ryan Pierce
|Created new AutoDesk Fusion 360 Post Processor. Modified Vectric Post Processors.
|Created new Fusion 360 Post Processor. It includes the changes listed below for the Vectric Post Processors. For Vectric, modified the Post Processors so that if the spindle does not spin up, it gives the user a Retry/Cancel dialog box instead of Abort/Retry/Ignore where Ignore is identical to Retry. Also, these Post Processors broke the Preview mode in the ShopBot software because the preview mode did the real spindle check and it failed because, of course, the spindle wasn't running. The new version will ignore the spindle check in preview mode.
|-
|11/8/2014
|Ryan Pierce
|Updated VCarve Post Processor
|Previously, installed new Post Processor to preset an Abort / Retry / Ignore dialog box when the spindle is started but doesn't spin up. Usual culprit is that a job is started when the the interlock is disabled, which results in the non-spinning bit crashing into the workpiece. Abort stops the job. Today, fixed Retry code. If you power on the VFD and the motor start is enabled, the VFD refuses to start. So I've re-programmed the Retry button to stop the VFD, wait 2 seconds, start the VFD, wait 2 more seconds, and check again to see if it is running. The Ignore button actually acts as Retry because we don't want someone clicking through this dialog box and damaging the machine. NOTE: The Aspire PC in the shop also has this Post Processor, but if you use Aspire, VCarve Pro, etc. on your personal computer, you will need the latest Post Processor to support this safety check.
|-
|11/8/2014
|Ryan Pierce
|Updated ShopBot software
|Did upgrade from 3.8.14 to 3.8.26. Installed latest firmware on ShopBot controller. (This was mandatory.) Two features of interest: Fixed occasional erractic behavior after repeated Stops and Resumes (and Nudges or Command Insertions). Reduced liklihood of Keypad lockup.
|-
|5/31/2015
|Ron Olson
|Created new VCarve Post Processors
|For drag/engraving bits, it's important that the spindle be turned '''off''' so as to not destroy the bit. Instead of manually modifying the sbp every time to remove the check that the spindle is turned on, I created a couple of new post processors (inches and mm, similar to Ryan's), that explicitly ''turn off'' the spindle. The user is given two opportunities to cancel the job if that is not what he/she wants.
|-
|}

== Outstanding Maintenance Issues ==

=== Lack of True E-Stop ===
As shipped, the ShopBot PRS does not support an Emergency Stop. This could be hacked, but it runs the risk of damaging the machine if engaged in a non-emergency situation. Suggested solution: Installing a 10A double pole 24V coil DIN mount relay, and powering the coil via the 24V supply through a normally closed E-Stop button. One pole will disconnect the 63V stepper motor current. One pole will break the control signal that enables the VFD and will cause the VFD to brake to a stop.

=== Automatic Dust Collection ===
The ShopBot has +5V TTL outputs that could be used to trigger automatic dust collection (when the spindle goes live) and/or a warning light (when the gantry is enabled to move.)

=== Limit Switch Issues ===
Every time you start the ShopBot, it resets itself so that the limit switches are disabled! You can turn them on (if memory serves) with the Values -> Input Switch Assignment menu item. Limit switches are really useful - but they need to be enabled. When they are, they will stop manual jogging when the limit is hit (although pressing the key again will let you continue moving the gantry) and they will also stop a running job (but give you the option of ignoring the limits.)

I found a couple more problems when testing all the limits. When I took the gantry to X maximum, the dust collector hose pulled off! I put it back on, but I'm not sure how stable this is. Also, when I originally set the Y maximum and minimum, I wanted as much spindle travel as possible. But it appears that if you're at the Y max and move in the X direction, you can hit the middle support with the dust collector boot. We've got several inches Y travel beyond the nominal 48", so we may want to look into reducing this to clear the supports.

== Resources ==
[[File:ShopBot PSOne Post Processors.zip]] - Post Processors for Vectric Aspire and VCarve Pro 8.0 which includes the change to check that the spindle actually started.

[[File:ShopBot_TC_PS1-NO-SPIN.zip]] - Post Processors for Vectric Aspire and VCarve Pro which include changes to explicitly *disable* spinning

[[File:ShopBot PSOne Fusion 360 Post Processor.zip]] - Post Processor for Autodesk Fusion 360 which includes the change to check that the spindle actually started.

[[Category:Fabrication]]
[[Category:CNC]]
[[Category:Future Things Bus Data Sources]]

Shopbot PRS CNC router

2020-01-26T15:18:35Z

Rfoto:

{{Template:EquipmentPage
|owner = PS:One
|serial = TBD.
|certification = yes
|hackable = no
|model = Shopbot PRS #10108 96-48
|arrived = 2014
|image = Shopbot.jpg
|doesitwork = yes
|contact = [[CNC|CNC Area Host]]
|where = Wood Shop
|value = $16000
|hostarea = CNC
}}
= ShopBot PRS #10108 96-48 =

* [http://www.shopbottools.com/mProducts/prSstandard.htm OEM website and specs]
* Nominal Cutting Area 96"x 48"x 6" (2.44m x 1.22m x .15m)
* Total Movement Area 102" x 50" x 8" (2.59m x 1.27m x .20m)
* Max spindle speed: 18000 RPM
* Min spindle speed: 4100 RPM

The spindle uses ER25 collets. These eventually wear out, so check before using them. Collets are a durable expendable.

Some people buy their own collets. There are a number of suppliers of collets, nuts, and related accessories. [http://www.techniksusa.com/ Techniks] and [http://www.shars.com/ Shars] are both brands that have been recommended by experienced CNC users, although other brands may also be of equivalent price and quality:

* [http://www.shars.com/1-4-ultra-precision-5-micron-er25-collet Shars ER25 Collet Ultra Precision 5 Micron]
* [https://www.ebay.com/itm/TECHNIKS-1-4-SUPER-PRECISION-ER25-COLLET-0002-ACCURACY-CNC-CHUCK-MILL-/130701349603?hash=item1e6e6852e3 Techniks 1/4" Super Precision ER25 Collet .0002 Accuracy]
* [https://www.toolstoday.com/cnc-high-precision-spring-collets-for-er25-tool-holder.html?variantids=11644,0&keywords=CO-286 Amana CNC High Precision Spring Collets for ER25 Tool Holder]
* [https://www.amazon.com/HHIP-3900-5215-ER-25-Spring-Collet/dp/B01ABWS9IG/ HHIP 3900-5215 ER-25 Spring Collet, 1/4"]
* [https://www.amazon.com/Dorian-Tool-Alloy-Precision-Collet/dp/B00CB14HXW/ Dorian Tool ER25 Alloy Steel Ultra Precision Collet, 0.236" - 0.276" Hole Size]

=Status=
August 2017: Dust collection system out of commission.

June 2017: There is an intermittent break in the wiring for the Z-axis Zero Plate. Check for continuity before using (the #1 input should light up on screen when you touch the contacts together). It usually works near the front of the table, but not halfway back. This will get fixed eventually, but it's a good idea to be in the habit of checking.

12/27/16 - Fixed Shopbot x-axis homing. The cable had been pulled on hard enough that some of the conductors broke inside the cable. It has been spliced, soldered, and heatshrinked back together.

= How to Get Authorized =

'''Authorization for this tool by authorized proctors only.''' This means you cannot get authorized by just anyone who is already authorized. You can only get authorized by a few people, the proctors listed below.

Authorization sessions are scheduled roughly monthly. Check the [https://www.meetup.com/Pumping-Station-One/events/ Meetup calendar] for upcoming authorizations. If no ShopBot sessions are currently scheduled, ask the [[CNC Area Host]] or on the [https://groups.google.com/group/pumping-station-one/ Google Group].

Be aware that this authorization consists of two parts; the first session is a classroom session that will cover the software required and introduce you to the essential settings and chip-load calculation, and the second part, scheduled separately, is a hands-on class.

== Authorizers ==
{| class="wikitable" border="1"
|-
|Elizabeth Koprucki
|Danger Committee
|-
|Bart Dring
|Danger Committee
|-
|Ryan Pierce
|Danger Committee
|-
|Nathan Ellis
|Danger Committee
|-
|Michael Skilton
|Danger Committee
|-
|Khoi Nguyen
|Michael Skilton
|-
|Andrew Camardella
|Elizabeth Koprucki
|-
|Matt Meshulam
|Andrew Camardella
|-
|David Earl
|Matt Meshulam
|-
|}

== How to Become an Authorizer ==
Get an ok from the area host. Successfully run an authorization supervised by an authorizer.
It's recommended that initial authorizations be limited to 2 member participants or less.

= Documentation =

[[File:Shopbotassembly.pdf|Shopbotassembly.pdf]]

[[File:Squaringshopbot.pdf|Squaring the ShopBot]]

[[File:Programming_handbook.pdf|Programming Handbook]]

[[File:PRS Maintenance Schedule.pdf|Maintenance Schedule]]

[[File:ShopBot_USB_Connection_Troubleshoot.pdf]] - USB Troubleshooting Guide

[[File:ShopBot_Tech_Support_FAQ_2016_09_12.pdf]] - Tech Support FAQ

[[File:SBG00142 User Guide 2013 05 01.pdf|SBG00142 User Guide 2013 05 01.pdf]] - User Guide

[[File:B17P.763_Schematic.pdf]] - Omer Nail Gun Documentation

[http://www.shopbottools.com/ShopBotDocs/files/quick%20start%20guide%202013%2007%2023.pdf QuickStart]

X, Y, Z probe: https://pumpingstationone.org/2015/09/xyz-finder-for-the-shopbot/

[http://drshopbot.com/index.php?title=Main_Page "Dr Shopbot" wiki]

[http://drshopbot.com/index.php?title=MaintainingConnection "Maintaining Connections"]

[[File:Shopbotmagnets.ai.zip]] - Template for the dust skirt and magnet placement.

== Tutorials ==
[https://www.youtube.com/watch?v=xWCZfYHOYWw Part 1 of our Shopbot Authorization] - This is available as a refresher only. You still need to go to the class when it happens to get access to the hands-on Part 2.

[http://www.woodguide.org/files/2014/07/CNCrouter_bit_basics.pdf Router Bit Basics for CNC - VERY USEFUL]

[https://groups.google.com/forum/?fromgroups=#!searchin/pumping-station-one/shopbot Shopbot Threads on Member List]

[https://groups.google.com/forum/?fromgroups=#!searchin/pumping-station-one/shopbot Shopbot Forum]

[https://groups.google.com/d/msg/pumping-station-one/vUF3iKRQ9yc/_qNnLXzZ3QcJ Overview of Cut Load calcualtions for setting bit feed and speed rates]

Vertanux1: This user teaches at Elgin Community College and has very good tutorials and downloadable textbook on Autodesk Inventor (which applies to Fusion 360 as well: http://www.vertanux1.com/ and https://www.youtube.com/user/vertanux1?reload=9

Online chipload calculator: https://www.guhdo.com/chipload-calculator

Fusion 360 Videos

NYC CNC - Several videos that provide an overview of downloading software, preferences, and basic sketch terms and steps. https://www.nyccnc.com/fusion-360/

Lars Christensen - CAD/CAM instructor hired by Autodesk to produce their Fusion 360 videos. The Absolute Basics and #LarsLive series are worth watching. https://www.youtube.com/watch?v=A5bc9c3S12g&feature=youtu.be

Maker's Muse CAD for Newbies Series - Provides a detailed overview of sketch dimensions, constraints, revolving, sweeping, and lofting, among many other topics. https://www.youtube.com/playlist?list=PLTCCNNvHC8PC40tcEqaJcgUMb97LNkLIn

Krenov Coffee Table - A fantastic overview of the design of a coffee table from scratch. Lots of CAD best practices. https://www.youtube.com/watch?v=J22j8RfETjs&feature=youtu.be

Fusion 360 V12 Engine - A long playlist series on a complex topic that demonstrates how powerful real CAD software can be. https://www.youtube.com/playlist?list=PLQl9vsO6sGSlasKFP-CAgnDs324Z6IW8s

= Software Tool Chain =
*Illustrator
*Inkscape
*Vectric Aspire
**Allows for 2D and 3D linework and toolpath creation
**Only available on the Shapeoko Computer
*Vectric V-Carve Makerspace Edition Version 9.0 (earlier versions may not be supported here anymore)
** http://www.vectric.com/products/vcarve/trial.html
**Allows for 2D linework and toolpath creation
**Allows at home use of V-Carve - output only at PS1
**Our Makerspace Code is: E4793-F6472-BB9E5-9B114-3FEEB-73649-16F4F
*Autodesk Fusion 360
**The ShopBot computer does not have this and may not be fast enough to run it.
**You '''MUST''' use the custom post-processor below. Otherwise, you will bypass the safety check to make sure the spindle really is running!
**For local '''Windows''', to install this on your local computer:
***Unzip and install this in C:\Users\YourName\AppData\Roaming\Autodesk\Fusion 360 CAM\Posts
***Note that AppData is often a hidden folder!
***Inside Fusion 360, when you select Actions / Post Process, under Configuration Folder, hit Setup and select Use Personal Posts.
**For local '''Mac'''
*** Unzip and install in Macintosh HD> Users> USERNAME> Autodesk> Fusion 360 CAM> Posts
*** In Fusion 360, when you select Actions > Post Process, under Settings select Personal Posts for the Source
**For '''Cloud'''
*** Open Fusion 360 and navigate to Libraries > Assets in the Data Panel.
*** Double click the Assets > CAMPosts folder to enter it.
*** Use the Upload button to upload the desired post processor from your local machine to the Assets > CAMPosts folder. This will upload the post to the cloud and allow you to access it anywhere you may login to your Fusion 360 account through My Cloud Posts.
*** After enabling cloud libraries in Fusion 360, you will be able to access your cloud post processor library by setting the Configuration Folder (Windows) or Source (Mac) to My Cloud Posts. Both of these dialog boxes are shown below. You will then be able to select the Cloud post you uploaded in the Post Configuration field (Windows) or the Post Processor field (Mac).
====Chip Load Calculation====
*[https://www.guhdo.com/chipload-calculator Chip Load Calculator by Guhdo]
*[http://www.pdsspindles.com/engineering-speeds Bit Parameter Overview by PDS Spindles]
*[https://www.monstertool.com/29/tech-data.htm Monster Tools Chip Load Calculator]
*[http://www.pdsspindles.com/admin/modules/page_editor/uploads/image/Chip%20load%20for%20common%20tool%20diameters%20(Inches).jpg Chip Load Chart by PDS Spindles]
*[https://groups.google.com/forum/#!searchin/pumping-station-one/makerspace$20edition/pumping-station-one/cTwfUHxESjU/7m_lI8UWCgAJ How to install Makerspace Version]

== User Tips & Troubleshooting Reports ==
[http://www.sgstool.com/PDF-speedfeeds/SGS-Speeds-Feeds-GP.pdf Some feed and speed recommendations for small bits]

Add your experiences with feeds and speeds or other tips here:
[[Shopbot_User_Tips]]

Add troubleshooting reports here:
[[Shopbot_Troubleshooting_Reports]]

=== Materials ===

* [[Shopbot_PRS_CNC_router/Aluminium|Aluminium]]
* [[Shopbot_PRS_CNC_router/Brass|Brass]]
* [[Shopbot_PRS_CNC_router/Wood|Wood]]

== Authorization Checklist ==

This is here as a checklist for proctors to follow when authorizing people. It can also help remind you of things after you are authorized. Just reading this does not authorizing you.

* How to get authorized
** Watch [http://www.meetup.com/Pumping-Station-One/ the meetup group] for a recurring class on the second Thursday and last Sunday of the month. Sometimes check [https://groups.google.com/forum/#!forum/pumping-station-one the forum] for announcements or ask on the forum if no announcements have been made for a few weeks.

* Authorization group size
** There is no cap to the software instruction preceding the machine usage portion of the class. If you come to this portion it is easier to get fully authorized at a later date.
** 3 machine users - each person will run a job (~1/2 hr each) and everyone will assist each other in completing a job profile and pocket cut. You must be present for the entire authorization

* Safety
** Safety Glasses
** Hearing Protection
** Dust Protection

* What can go wrong (and what to do)

* How does machine work
** Axes
** Motors
** Spindle

* Daily Maintenance
** Spindle bearing warm up.
*** The "C5" warm up routine should be run on the first job of the day. It runs the spindle at 3 speeds for 3 minutes each to warm up the bearings. (When it doubt, warm it up)

* Extended Maintenance
** See maintenance schedule file under documentation.
** Grease the racks
** Use Grease type: Manual states any type is safe there is some in the draw

* Machine Control
** Turn on sequence
*** Log into computer
*** Turn on Shopbot big red and yellow twist switch (see zeroing below)
*** Insert Key and turn to "engaged" position.
*** The VDF should light up, the spindle fan should be on.
*** Start "Shopbot 3" program.
*** Open Tools...Spindle RPM Control menu (to allow RPM control)
**** Make sure collet is tightened or no tool or nut is installed
**** Run the C5 warm up routine
** Jogging
*** Keypad
*** Arrow Keys + Page Up, Page Down (ctrl for fast jog)

* CAM Software
** Vectric V Carve
** Just the basics...separate class for advanced V Carve.
** Online videos

* Running your Job
** Zeroing X & Y
*** With machine off slow push gantry towards X0 until it hits hard stops (optional)
*** Turn on big red switch while still holding gantry.
*** Jog machine away from X0 Y0 so machine will find switches
*** Click X, Y zero button.
** Zeroing Z (top of work piece)
*** Jog over your work piece
*** Place Z zero plate on work piece under the bit
*** Place clip on bit
*** Test connection by touching plate to bit and watch for light #1 to light
*** Click the Z 0 button (it will touch off twice!!!)
*** If Z is critical, you may want to verify that your bit has been zeroed properly by using a "MZ,0" command over the surface you have zeroed the bit to. Repeat zeroing if not correct.

* Waste Board and clamping

* Collets, Bits, Feeds and Speeds
** Feeds and Speeds
*** Use a Cut Load Calculator to determine which feeds and speeds you should be using for your specific bits. An overview is avaialble at: [https://groups.google.com/d/msg/pumping-station-one/vUF3iKRQ9yc/_qNnLXzZ3QcJ]
** Collets
*** We currently have collets for 1/2, 1/4, 3/16 and 1/8" shank bits.
*** Try to keep them clean and store them away from dust between uses. Dust between the gaps will produce runout. The drawer mounted under the Shopbot is the right place to store these items.
*** If the collet nuts are not threading smoothly try cleaning the threads with a small brush, spindle threads as well.
** Bits
*** Use bits designed for the material you are cutting. Don't just steal a bits from the Bridgeport. They won't do a good job and will probably overheat.
*** For cutting out things, use the smallest appropriate bit. Using a 1/2" bit to cutout will just create a lot of mess.

* ShopBot should not be used for...
** Metals other than aluminum
** Cutting anything that requires coolant or lubricant (it will ruin the waste board)
** Ripping lumber (use the table saw)
** Thickness Planning (Use the planner if you can)
** Drilling holes with drill bits (a small end mill works better)

* How to leave the machine (be excellent)
** Machine
*** Home the machine to X0, Y0
*** Turn off both switches
*** Remove Key
*** Remove bit and collet.
*** Place both collet wrenches on top of electronics box
*** clean up work area
*** Smooth out waste board if you puckered it at all.
*** Check if the dust collector needs to be emptied

** Post a picture on our [[Blog]] please!

== Use checklist ==

PS1 is experimenting with the use of checklists to encourage the safe use and proper care of tools in the workspace. The latest version of the [[checklists]] for this tool is stored as a [https://docs.google.com/document/d/1zxrvQX0DXaLxaXkaKCKpZ-PAgnDak6ezKKBkdu_Fw1U/edit?usp=sharing Google Doc] that can be edited by anyone. If you make changes, update the effective date at the bottom of the document. Print a new copy, and replace the old one.

Physical checklists are necessarily constrained in length. Following is a more extensive pre-flight checklist:

* Did you home the machine?
* Is the dust collect gate open?
* Are you sure you have the right X, Y orientation for your file and material?
* Did you set the proper X,Y zero for your work piece on the Shopbot.
* Is the correct bit installed and tight?
* Is the key in and turned on?
* Is the dust skirt set right so it does not get smashed.
* Is Z zero set to the work top?
* Are the touch plate and clip returned?
* Is the material properly secured?
* Open the Shopbot spindle control dialog (Tools > Spindle RPM Control)
* Safety glasses, hearing protection on.
* Start the job with the E-Stop ready to hit.
* Turn on dust collector ( I like to wait so I can hear that things sound right on the shopbot before turning on the collector)

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Elizabeth Koprucki
|Danger Committee
|
|-
|Bart Dring
|Danger Committee
|
|-
|Ryan Pierce
|Danger Committee
|
|-
|Nathan Ellis
|Danger Committee
|
|-
|Michael Skilton
|Danger Committee
|
|-
|Arturo Duarte
|Bart
|
|-
|Derek Bever
|Bart
|
|-
|Everett
|Bart
|
|-
|Vincent Colombo
|Bart
|
|-
|[[User:justin|Justin T. Conroy]]
|Bart
|
|-
|Hugh Sato
|Bart
|
|-
|Sergey Nekrasov
|Bart
|
|-
|Valerie Moore
|Bart
|
|-
|Patrick Schless
|Bart
|
|-
|Tom Forajter
|Bart
|
|-
|Todd Allen
|Michael Skilton
|
|-
|[[User:RogerMoore|Roger Moore]]
|Bart
|
|-
|Tim Saylor
|Bart
|
|-
|Hef
|Bart
|
|-
|Jeff McBride
|Bart
|
|-
| Maxwell ?
| Michael Skilton
|
|-
|Samuel Swope
|Michael Skilton
|
|-
| Khoi Nguyen
|Michael Skilton
|
|-
|Brian Chojnowski
|Michael Skilton
|
|-
|Josh Cooper
|Bart
|
|-
|Andrew Camardella
|Bart
|
|-
|Adam Glick
|Bart
|
|-
|Yehuda Braun
|Bart
|
|-
| Jeff Kantarek
| Michael Sklton
|
|-
| Justin Miles
|Michael Skilton
|
|-
|Will Garza
|Michael Skilton
|
|-
|Clarence Risher
|Michael Skilton
|
|-
|[[User:ericbeau|Eric Beauchamp]]
|Michael Skilton
|
|-
|[[User:Jason|Jason]]
|Michael Skilton
|
|-
|Eric Stein
|Bart
|
|-
|Colin Parsons
|Bart
|
|-
|David Ditzler
|Bart
|
|-
|Ray Doeksen
|Bart Dring
|
|-
|Ron Bean
|Khoi Nguyen & Michael Skilton
|
|-
| Thomas Wright
|Khoi Nguyen & Michael Skilton
|
|-
|David Morton
|Bart Dring
|
|-
|Ron Olson
|Bart Dring
|
|-
|Kyle Bieneman
|Bart Dring
|
|-
|[[User:amishhammer|Tom Judge]]
|Michael Skilton
|
|-
|Bryan Gleason
|Michael Skilton
|
|-
|Dave Schact
|Ryan Pierce
|
|-
|Chris Agocs
|Andrew Camardella
|
|-
|[[user:kuroishi | Doorman Dave ]]
|Andrew Camardella
|
|-
|Alec Weege
|Andrew Camardella
|
|-
|Sam Reicks
|Andrew Camardella
|
|-
|Touly Phiachantharath
|Andrew Camardella
|
|-
|Lucas Goossen
|Andrew Camardella
|
|-
|[[user:Tina|Tina C]]
|Andrew Camardella
|
|-
|Ryan Neuman
|Andrew Camardella
|
|-
|Dan Loeser
|Andrew Camardella
|
|-
|Ben Bogler
|Andrew Camardella
|
|-
|Erin Banwell
|Ryan Pierce
|
|-
|Brad Rios
|Ryan Pierce
|
|-
|Aaron Carlock
|Andrew Camardella
|
|-
|James Villalpando
|Andrew Camardella
|
|-
|Connor Jansen
|Andrew Camardella
|
|-
|Tait Leswing
|Bart
|
|-
|Raj Perera
|Khoi Nguyen
|
|-
|Keith Hultman
|Andrew Camardella
|
|-
|David Srebro
|Andrew Camardella
|
|-
|[[user:Wessing | Erik Wessing ]]
|Andrew Camardella
|
|-
|Leeswann Bolden
|Andrew Camardella
|
|-
|Josh Myers
|Andrew Camardella
|
|-
|Kurt Ziegel
|Andrew Camardella
|
|-
|Glenn Powers
|Andrew Camardella
|
|-
|[[User:mqudsi|Mahmoud Al-Qudsi]]
|Andrew Camardella
|
|-
|Casey Olson
|Khoi
|
|-
|Mike Jones
|Andrew Camardella
|
|-
|Aaron Feigen
|Andrew Camardella
|
|-
|Jim Baker
|Andrew Camardella
|
|-
|Eric Reusche
|Khoi Nguyen
|
|-
|Ralph Brendler
|Andrew Camardella
|
|-
|John McDonald
|Andrew Camardella
|
|-
|Alex Al-Hamdan
|Andrew Camardella
|
|-
|Eugene Liokumovich
|Andrew Camardella
|
|-
|Randal Cox
|Andrew Camardella
|
|-
|Simon Pyle
|Andrew Camardella
|
|-
|Jean Michel Crettaz
|Andrew Camardella
|
|-
|Brian Zable
|Andrew Camardella
|
|-
|Daylan Dufelmeier
|Andrew Camardella
|
|-
|Steve Kruse
|Matt Meshulam
|
|-
|Mike Mandrea
|Andrew Camardella
|
|-
|Jeff Zelnio
|Andrew Camardella
|
|-
|Aaron Stoddart
|Matt Meshulam
|
|-
|Koun Park
|Matt Meshulam
|
|-
|Dan Baltudis
|Matt Meshulam
|
|-
|Curtiss Cooke
|Matt Meshulam
|
|-
|Jeannine Chuchan
|Matt Meshulam
|
|-
|Brennan Koziarz
|Matt Meshulam
|
|-
|Brandon Love
|Matt Meshulam
|
|-
|Mike Vitale
|Matt Meshulam
|
|-
|Emma Purola
|Matt Meshulam
|
|-
|Chris Kohl
|Matt Meshulam
|
|-
|Daniel Sojka
|Matt Meshulam
|
|-
|Naguib Azab
|Matt Meshulam
|
|-
|Mark Zumwalt
|Matt Meshulam
|
|-
|Joseph Juhnke
|Andrew Camardella
|
|-
|Alex Berkowitz
|Andrew Camardella
|
|-
|Andy Muhic
|Matt Meshulam
|
|-
|Adam Stein
|Matt Meshulam
|
|-
|John Farmer
|Matt Meshulam
|
|-
|Joshua Havenga
|Matt Meshulam
|
|-
|[[user:mct|McTavish McArdle]]
|Matt Meshulam
|
|-
|Frank Bowles
|Matt Meshulam
|
|-
|Joe Iklov
|Matt Meshulam
|
|-
|Matthew Quigley
|Matt Meshulam
|
|-
|Derwin Umali
|Andrew Camardella
|
|-
|Doug Mahoney
|Matt Meshulam
|
|-
|Rob Robinson
|Matt Meshulam
|
|-
|Dan Sloboda
|Matt Meshulam
|
|-
|Jacob Collins
|Matt Meshulam
|
|-
|Donald Wells
|Matt Meshulam
|
|-
|[[user:jim|Jim Brink]]
|Matt Meshulam
|
|-
|[[user:mkeith|Matt Keith]]
|Matt Meshulam
|
|-
|[[user:vmorris|Victoria Morris]]
|Matt Meshulam
|
|-
|[[user:bobsabayesian|Bob Loos]]
|Matt Meshulam
|
|-
|[[user:muthpete|Peter Muth]]
|Matt Meshulam
|
|-
|[[user:guijemont|Guillaume Emont]]
|Matt Meshulam
|
|-
|[[user:erikthefunk|Erik Funkhouser]]
|Matt Meshulam
|
|-
|[[user:mrashes|Max Rashes]]
|Matt Meshulam
|
|-
|[[user:panchan99|Juan Ramos]]
|Matt Meshulam
|
|-
|[[user:Justjoe|Joe Dowling]]
|Matt Meshulam
|
|-
|[[user:smash|Ashley Matrisciano]]
|Matt Meshulam
|
|-
|Ryan Kapp
|Matt Meshulam
|
|-
|Idris Raja
|Matt Meshulam
|
|-
|[[user:Dannyblanchard|Danny Blanchard]]
|Matt Meshulam
|
|-
|Aaron Mintz
|Matt Meshulam
|
|-
|[[user:ianstubbs|Ian Stubbs]]
|Matt Meshulam
|
|-
|[[user:skynaya|Sky Nova]]
|Matt Meshulam
|
|-
|Chris Ruhland
|Matt Meshulam
|
|-
|[[user:Jaypee|Jay Pee]]
|Matt Meshulam
|
|-
|[[user:Ryanmafi|Ryan Fiebing]]
|Matt Meshulam
|
|-
|[[user:sblaszak|Shawn Blaszak]]
|Matt Meshulam
|
|-
|[[user:tonyiacullo|Tony Iacullo]]
|Matt Meshulam
|
|-
|Mark Haughey
|Matt Meshulam
|
|-
|Chris Iacullo
|Matt Meshulam
|
|-
|Ian Monroe
|Matt Meshulam
|
|-
|Ashish Jasani
|Matt Meshulam
|
|-
|Kurt Gilman
|Matt Meshulam
|
|-
|Abel Greenwald
|Matt Meshulam
|
|-
|Vaidotas (Vai) Staugaitis
|Matt Meshulam
|
|-
|Leo Battikhi
|Matt Meshulam
|
|-
|Matt Schaid
|Matt Meshulam
|
|-
|Jamie Vollmer
|Matt Meshulam
|
|-
|Bhairavi Warke
|Matt Meshulam
|
|-
|Denis Kuznetsov
|Matt Meshulam
|
|-
|Brian Carstensen
|Matt Meshulam
|
|-
|Rob Dumas
|Matt Meshulam
|
|-
|Mark Weiser
|Matt Meshulam
|
|-
|Tom Burtonwood
|Matt Meshulam
|
|-
|Steve Madonna
|Matt Meshulam
|
|-
|Jason Araujo
|Matt Meshulam
|
|-
|Bruce Alan Mace
|Matt Meshulam
|
|-
|Molly Adamski
|Matt Meshulam
|
|-
|Jeremy Shaw
|Matt Meshulam
|
|-
|Sam Chen
|Matt Meshulam
|
|-
|John McBride
|Matt Meshulam
|
|-
|Adomas Tautkus
|Matt Meshulam
|
|-
|Tim Buckley
|Matt Meshulam
|
|-
|Martina Josimovska
|Matt Meshulam
|
|-
|James Jacobs
|Matt Meshulam
|
|-
|George Shaw
|Matt Meshulam
|
|-
|David Earl
|Matt Meshulam
|
|-
|[[User:pedrosk| Eduard Breuer]]
|Matt Meshulam
|
|-|-
|Matthew Kim
|Matt Meshulam
|
|-
|Corey Peoples
|Matt Meshulam
|
|-
|Paul Graham
|Matt Meshulam
|
|-
|Matt Grunstad
|Matt Meshulam
|
|-
|Rolf Scheidt
|Matt Meshulam
|
|-
|Arjun Sharma
|Matt Meshulam
|
|-
|Chris Laurent
|Matt Meshulam
|
|-
|[[User:dwlocks|Dan Locks]]
|Matt Meshulam
|
|-
|Zack Sasnow
|Matt Meshulam
|
|-
|Ben Stringer
|Matt Meshulam
|
|-
|[[User:Ekaj|Jacob Snyder]]
|Matt Meshulam
|8/24/17
|-
|James Beck
|Matt Meshulam
|9/13/17
|-
| Sam Gates
|Matt Meshulam
|10/01/17
|-
| Tommy TBones Cramer
|Matt Meshulam
|09/24/17
|-
| tee
|Matt Meshulam
|10/26/17
|-
|[[User:wittnl|Nathan Witt]]
|Matt Meshulam
|2017-12-09
|-
|[[User:GalaxyCascade|Steve Griegoliet]]
|Matt Meshulam
|12/09/17
|-
| Chinbayar Davaatseren
| Matt Meshulam
| 12/09/17
|-
|Theo T
|David Earl
|1/20/18
|-
|[[User:Frenchy|Jeremie Davis]]
|David Earl
|1/21/18
|-
|Armani Barron
|Matt Meshulam
|9/16/17
|-
|Scott Fullman
|David Earl
|02/24/18
|-
|Michael Donovan
|David Earl
|03/04/2018
|-
|Damon Carrvesco
|David Earl
|03/26/2018
|-
|Ryan Kelly
|David Earl
|03/26/2018
|-
|Will Coffin
|David Earl
|03/26/2018
|-
|Shabab Mustafa
|David Earl
|03/26/2018
|-
|Bruce Mace
|David Earl
|03/26/2018
|-
|Shahnawas Khokhar
|David Earl
|03/26/2018
|-
|Seth Cothron
|David Earl
|04/22/2018
|-
|Matthew Currey
|David Earl
|04/22/2018
|-
|Adam Hall
|David Earl
|04/29/2018
|-
|Kevin Huemann
|David Earl
|04/29/2018
|-
|Donzell Gordon
|David Earl
|04/28/2018
|-
|Nelson Reyes
|David Earl
|05/26/2018
|-
|David DesRoberts
|David Earl
|05/26/2018
|-
|Brendan Fortune
|David Earl
|06/02/2018
|-
|Chris Albert
|David Earl
|06/17/2018
|-
|Nate Myren
|David Earl
|06/23/2018
|-
|Eli Scholssberg
|David Earl
|06/23/2018
|-
|Szymon Mirek
|David Earl
|06/24/2018
|-
|Dan Willmott
|David Earl
|06/24/2018
|-
|Mark Treiber
|David Earl
|10/28/2018
|-
|Charlie Kepner
|David Earl
|02/20/2019
|-
|Kevin Cluff
|David Earl
|02/20/2019
|-
|Greg Bell
|David Earl
|03/23/19
|-
|Paul Ocampo
|David Earl
|03/28/19
|-
|Fritz Sullivan
|David Earl
|03/31/19
|-
|Daniel Gulick
|David Earl
|12/10/2018
|-
|Alex Biardo
|David Earl
|05/07/2019
|-
|Brendan Byrne
|David Earl
|05/07/2019
|-
|Sam Vuchetich
|David Earl
|09/29/2019
|-
-
|Antina Lee
|David Earl
|09/29/2019
-
|Rob German
|David Earl
|09/29/2019
-
|Ryan Zoghlin
|David Earl
|1/25/2020
|-}

If you have been authorized but cannot log in, request to be added to the "ShopBot Authorized" Samba group (send an email to info (at) pumpingstationone.org with your username and the name of the person who certified you) so that your login works. If you don't have a log-in on https://members.pumpingstationone.org/ you will have issues here - sign up on that site first if you haven't already.

= Maintenance =

== Maintenance Log ==
{| class="wikitable" border="1"
!Date
!Preformed by
!Service Type
!Notes
|-
|4/16/2017
|Ryan Pierce
|Created new AutoDesk Fusion 360 Post Processor. Modified Vectric Post Processors.
|Created new Fusion 360 Post Processor. It includes the changes listed below for the Vectric Post Processors. For Vectric, modified the Post Processors so that if the spindle does not spin up, it gives the user a Retry/Cancel dialog box instead of Abort/Retry/Ignore where Ignore is identical to Retry. Also, these Post Processors broke the Preview mode in the ShopBot software because the preview mode did the real spindle check and it failed because, of course, the spindle wasn't running. The new version will ignore the spindle check in preview mode.
|-
|11/8/2014
|Ryan Pierce
|Updated VCarve Post Processor
|Previously, installed new Post Processor to preset an Abort / Retry / Ignore dialog box when the spindle is started but doesn't spin up. Usual culprit is that a job is started when the the interlock is disabled, which results in the non-spinning bit crashing into the workpiece. Abort stops the job. Today, fixed Retry code. If you power on the VFD and the motor start is enabled, the VFD refuses to start. So I've re-programmed the Retry button to stop the VFD, wait 2 seconds, start the VFD, wait 2 more seconds, and check again to see if it is running. The Ignore button actually acts as Retry because we don't want someone clicking through this dialog box and damaging the machine. NOTE: The Aspire PC in the shop also has this Post Processor, but if you use Aspire, VCarve Pro, etc. on your personal computer, you will need the latest Post Processor to support this safety check.
|-
|11/8/2014
|Ryan Pierce
|Updated ShopBot software
|Did upgrade from 3.8.14 to 3.8.26. Installed latest firmware on ShopBot controller. (This was mandatory.) Two features of interest: Fixed occasional erractic behavior after repeated Stops and Resumes (and Nudges or Command Insertions). Reduced liklihood of Keypad lockup.
|-
|5/31/2015
|Ron Olson
|Created new VCarve Post Processors
|For drag/engraving bits, it's important that the spindle be turned '''off''' so as to not destroy the bit. Instead of manually modifying the sbp every time to remove the check that the spindle is turned on, I created a couple of new post processors (inches and mm, similar to Ryan's), that explicitly ''turn off'' the spindle. The user is given two opportunities to cancel the job if that is not what he/she wants.
|-
|}

== Outstanding Maintenance Issues ==

=== Lack of True E-Stop ===
As shipped, the ShopBot PRS does not support an Emergency Stop. This could be hacked, but it runs the risk of damaging the machine if engaged in a non-emergency situation. Suggested solution: Installing a 10A double pole 24V coil DIN mount relay, and powering the coil via the 24V supply through a normally closed E-Stop button. One pole will disconnect the 63V stepper motor current. One pole will break the control signal that enables the VFD and will cause the VFD to brake to a stop.

=== Automatic Dust Collection ===
The ShopBot has +5V TTL outputs that could be used to trigger automatic dust collection (when the spindle goes live) and/or a warning light (when the gantry is enabled to move.)

=== Limit Switch Issues ===
Every time you start the ShopBot, it resets itself so that the limit switches are disabled! You can turn them on (if memory serves) with the Values -> Input Switch Assignment menu item. Limit switches are really useful - but they need to be enabled. When they are, they will stop manual jogging when the limit is hit (although pressing the key again will let you continue moving the gantry) and they will also stop a running job (but give you the option of ignoring the limits.)

I found a couple more problems when testing all the limits. When I took the gantry to X maximum, the dust collector hose pulled off! I put it back on, but I'm not sure how stable this is. Also, when I originally set the Y maximum and minimum, I wanted as much spindle travel as possible. But it appears that if you're at the Y max and move in the X direction, you can hit the middle support with the dust collector boot. We've got several inches Y travel beyond the nominal 48", so we may want to look into reducing this to clear the supports.

== Resources ==
[[File:ShopBot PSOne Post Processors.zip]] - Post Processors for Vectric Aspire and VCarve Pro 8.0 which includes the change to check that the spindle actually started.

[[File:ShopBot_TC_PS1-NO-SPIN.zip]] - Post Processors for Vectric Aspire and VCarve Pro which include changes to explicitly *disable* spinning

[[File:ShopBot PSOne Fusion 360 Post Processor.zip]] - Post Processor for Autodesk Fusion 360 which includes the change to check that the spindle actually started.

[[Category:Fabrication]]
[[Category:CNC]]
[[Category:Future Things Bus Data Sources]]

Shopbot PRS CNC router

2020-01-26T15:13:02Z

Rfoto:

{{Template:EquipmentPage
|owner = PS:One
|serial = TBD.
|certification = yes
|hackable = no
|model = Shopbot PRS #10108 96-48
|arrived = 2014
|image = Shopbot.jpg
|doesitwork = yes
|contact = [[CNC|CNC Area Host]]
|where = Wood Shop
|value = $16000
|hostarea = CNC
}}
= ShopBot PRS #10108 96-48 =

* [http://www.shopbottools.com/mProducts/prSstandard.htm OEM website and specs]
* Nominal Cutting Area 96"x 48"x 6" (2.44m x 1.22m x .15m)
* Total Movement Area 102" x 50" x 8" (2.59m x 1.27m x .20m)
* Max spindle speed: 18000 RPM
* Min spindle speed: 4100 RPM

The spindle uses ER25 collets. These eventually wear out, so check before using them. Collets are a durable expendable.

Some people buy their own collets. There are a number of suppliers of collets, nuts, and related accessories. [http://www.techniksusa.com/ Techniks] and [http://www.shars.com/ Shars] are both brands that have been recommended by experienced CNC users, although other brands may also be of equivalent price and quality:

* [http://www.shars.com/1-4-ultra-precision-5-micron-er25-collet Shars ER25 Collet Ultra Precision 5 Micron]
* [https://www.ebay.com/itm/TECHNIKS-1-4-SUPER-PRECISION-ER25-COLLET-0002-ACCURACY-CNC-CHUCK-MILL-/130701349603?hash=item1e6e6852e3 Techniks 1/4" Super Precision ER25 Collet .0002 Accuracy]
* [https://www.toolstoday.com/cnc-high-precision-spring-collets-for-er25-tool-holder.html?variantids=11644,0&keywords=CO-286 Amana CNC High Precision Spring Collets for ER25 Tool Holder]
* [https://www.amazon.com/HHIP-3900-5215-ER-25-Spring-Collet/dp/B01ABWS9IG/ HHIP 3900-5215 ER-25 Spring Collet, 1/4"]
* [https://www.amazon.com/Dorian-Tool-Alloy-Precision-Collet/dp/B00CB14HXW/ Dorian Tool ER25 Alloy Steel Ultra Precision Collet, 0.236" - 0.276" Hole Size]

=Status=
August 2017: Dust collection system out of commission.

June 2017: There is an intermittent break in the wiring for the Z-axis Zero Plate. Check for continuity before using (the #1 input should light up on screen when you touch the contacts together). It usually works near the front of the table, but not halfway back. This will get fixed eventually, but it's a good idea to be in the habit of checking.

12/27/16 - Fixed Shopbot x-axis homing. The cable had been pulled on hard enough that some of the conductors broke inside the cable. It has been spliced, soldered, and heatshrinked back together.

= How to Get Authorized =

'''Authorization for this tool by authorized proctors only.''' This means you cannot get authorized by just anyone who is already authorized. You can only get authorized by a few people, the proctors listed below.

Authorization sessions are scheduled roughly monthly. Check the [https://www.meetup.com/Pumping-Station-One/events/ Meetup calendar] for upcoming authorizations. If no ShopBot sessions are currently scheduled, ask the [[CNC Area Host]] or on the [https://groups.google.com/group/pumping-station-one/ Google Group].

Be aware that this authorization consists of two parts; the first session is a classroom session that will cover the software required and introduce you to the essential settings and chip-load calculation, and the second part, scheduled separately, is a hands-on class.

== Authorizers ==
{| class="wikitable" border="1"
|-
|Elizabeth Koprucki
|Danger Committee
|-
|Bart Dring
|Danger Committee
|-
|Ryan Pierce
|Danger Committee
|-
|Nathan Ellis
|Danger Committee
|-
|Michael Skilton
|Danger Committee
|-
|Khoi Nguyen
|Michael Skilton
|-
|Andrew Camardella
|Elizabeth Koprucki
|-
|Matt Meshulam
|Andrew Camardella
|-
|David Earl
|Matt Meshulam
|-
|}

== How to Become an Authorizer ==
Get an ok from the area host. Successfully run an authorization supervised by an authorizer.
It's recommended that initial authorizations be limited to 2 member participants or less.

= Documentation =

[[File:Shopbotassembly.pdf|Shopbotassembly.pdf]]

[[File:Squaringshopbot.pdf|Squaring the ShopBot]]

[[File:Programming_handbook.pdf|Programming Handbook]]

[[File:PRS Maintenance Schedule.pdf|Maintenance Schedule]]

[[File:ShopBot_USB_Connection_Troubleshoot.pdf]] - USB Troubleshooting Guide

[[File:ShopBot_Tech_Support_FAQ_2016_09_12.pdf]] - Tech Support FAQ

[[File:SBG00142 User Guide 2013 05 01.pdf|SBG00142 User Guide 2013 05 01.pdf]] - User Guide

[[File:B17P.763_Schematic.pdf]] - Omer Nail Gun Documentation

[http://www.shopbottools.com/ShopBotDocs/files/quick%20start%20guide%202013%2007%2023.pdf QuickStart]

X, Y, Z probe: https://pumpingstationone.org/2015/09/xyz-finder-for-the-shopbot/

[http://drshopbot.com/index.php?title=Main_Page "Dr Shopbot" wiki]

[http://drshopbot.com/index.php?title=MaintainingConnection "Maintaining Connections"]

[[File:Shopbotmagnets.ai.zip]] - Template for the dust skirt and magnet placement.

== Tutorials ==
[https://www.youtube.com/watch?v=xWCZfYHOYWw Part 1 of our Shopbot Authorization] - This is available as a refresher only. You still need to go to the class when it happens to get access to the hands-on Part 2.

[http://www.woodguide.org/files/2014/07/CNCrouter_bit_basics.pdf Router Bit Basics for CNC - VERY USEFUL]

[https://groups.google.com/forum/?fromgroups=#!searchin/pumping-station-one/shopbot Shopbot Threads on Member List]

[https://groups.google.com/forum/?fromgroups=#!searchin/pumping-station-one/shopbot Shopbot Forum]

[https://groups.google.com/d/msg/pumping-station-one/vUF3iKRQ9yc/_qNnLXzZ3QcJ Overview of Cut Load calcualtions for setting bit feed and speed rates]

Vertanux1: This user teaches at Elgin Community College and has very good tutorials and downloadable textbook on Autodesk Inventor (which applies to Fusion 360 as well: http://www.vertanux1.com/ and https://www.youtube.com/user/vertanux1?reload=9

Online chipload calculator: https://www.guhdo.com/chipload-calculator

Fusion 360 Videos

NYC CNC - Several videos that provide an overview of downloading software, preferences, and basic sketch terms and steps. https://www.nyccnc.com/fusion-360/

Lars Christensen - CAD/CAM instructor hired by Autodesk to produce their Fusion 360 videos. The Absolute Basics and #LarsLive series are worth watching. https://www.youtube.com/watch?v=A5bc9c3S12g&feature=youtu.be

Maker's Muse CAD for Newbies Series - Provides a detailed overview of sketch dimensions, constraints, revolving, sweeping, and lofting, among many other topics. https://www.youtube.com/playlist?list=PLTCCNNvHC8PC40tcEqaJcgUMb97LNkLIn

Krenov Coffee Table - A fantastic overview of the design of a coffee table from scratch. Lots of CAD best practices. https://www.youtube.com/watch?v=J22j8RfETjs&feature=youtu.be

Fusion 360 V12 Engine - A long playlist series on a complex topic that demonstrates how powerful real CAD software can be. https://www.youtube.com/playlist?list=PLQl9vsO6sGSlasKFP-CAgnDs324Z6IW8s

= Software Tool Chain =
*Illustrator
*Inkscape
*Vectric Aspire
**Allows for 2D and 3D linework and toolpath creation
**Only available on the Shapeoko Computer
*Vectric V-Carve Makerspace Edition Version 9.0 (earlier versions may not be supported here anymore)
** http://www.vectric.com/products/vcarve/trial.html
**Allows for 2D linework and toolpath creation
**Allows at home use of V-Carve - output only at PS1
**Our Makerspace Code is: E4793-F6472-BB9E5-9B114-3FEEB-73649-16F4F
*Autodesk Fusion 360
**The ShopBot computer does not have this and may not be fast enough to run it.
**You '''MUST''' use the custom post-processor below. Otherwise, you will bypass the safety check to make sure the spindle really is running!
**For local '''Windows''', to install this on your local computer:
***Unzip and install this in C:\Users\YourName\AppData\Roaming\Autodesk\Fusion 360 CAM\Posts
***Note that AppData is often a hidden folder!
***Inside Fusion 360, when you select Actions / Post Process, under Configuration Folder, hit Setup and select Use Personal Posts.
**For local '''Mac'''
*** Unzip and install in Macintosh HD> Users> USERNAME> Autodesk> Fusion 360 CAM> Posts
*** In Fusion 360, when you select Actions > Post Process, under Settings select Personal Posts for the Source
**For '''Cloud'''
*** Open Fusion 360 and navigate to Libraries > Assets in the Data Panel.
*** Double click the Assets > CAMPosts folder to enter it.
*** Use the Upload button to upload the desired post processor from your local machine to the Assets > CAMPosts folder. This will upload the post to the cloud and allow you to access it anywhere you may login to your Fusion 360 account through My Cloud Posts.
*** After enabling cloud libraries in Fusion 360, you will be able to access your cloud post processor library by setting the Configuration Folder (Windows) or Source (Mac) to My Cloud Posts. Both of these dialog boxes are shown below. You will then be able to select the Cloud post you uploaded in the Post Configuration field (Windows) or the Post Processor field (Mac).
====Chip Load Calculation====
*[https://www.guhdo.com/chipload-calculator Chip Load Calculator by Guhdo]
*[http://www.pdsspindles.com/engineering-speeds Bit Parameter Overview by PDS Spindles]
*[https://www.monstertool.com/29/tech-data.htm Monster Tools Chip Load Calculator]
*[http://www.pdsspindles.com/admin/modules/page_editor/uploads/image/Chip%20load%20for%20common%20tool%20diameters%20(Inches).jpg Chip Load Chart by PDS Spindles]
*[https://groups.google.com/forum/#!searchin/pumping-station-one/makerspace$20edition/pumping-station-one/cTwfUHxESjU/7m_lI8UWCgAJ How to install Makerspace Version]

== User Tips & Troubleshooting Reports ==
[http://www.sgstool.com/PDF-speedfeeds/SGS-Speeds-Feeds-GP.pdf Some feed and speed recommendations for small bits]

Add your experiences with feeds and speeds or other tips here:
[[Shopbot_User_Tips]]

Add troubleshooting reports here:
[[Shopbot_Troubleshooting_Reports]]

=== Materials ===

* [[Shopbot_PRS_CNC_router/Aluminium|Aluminium]]
* [[Shopbot_PRS_CNC_router/Brass|Brass]]
* [[Shopbot_PRS_CNC_router/Wood|Wood]]

== Authorization Checklist ==

This is here as a checklist for proctors to follow when authorizing people. It can also help remind you of things after you are authorized. Just reading this does not authorizing you.

* How to get authorized
** Watch [http://www.meetup.com/Pumping-Station-One/ the meetup group] for a recurring class on the second Thursday and last Sunday of the month. Sometimes check [https://groups.google.com/forum/#!forum/pumping-station-one the forum] for announcements or ask on the forum if no announcements have been made for a few weeks.

* Authorization group size
** There is no cap to the software instruction preceding the machine usage portion of the class. If you come to this portion it is easier to get fully authorized at a later date.
** 3 machine users - each person will run a job (~1/2 hr each) and everyone will assist each other in completing a job profile and pocket cut. You must be present for the entire authorization

* Safety
** Safety Glasses
** Hearing Protection
** Dust Protection

* What can go wrong (and what to do)

* How does machine work
** Axes
** Motors
** Spindle

* Daily Maintenance
** Spindle bearing warm up.
*** The "C5" warm up routine should be run on the first job of the day. It runs the spindle at 3 speeds for 3 minutes each to warm up the bearings. (When it doubt, warm it up)

* Extended Maintenance
** See maintenance schedule file under documentation.
** Grease the racks
** Use Grease type: Manual states any type is safe there is some in the draw

* Machine Control
** Turn on sequence
*** Log into computer
*** Turn on Shopbot big red and yellow twist switch (see zeroing below)
*** Insert Key and turn to "engaged" position.
*** The VDF should light up, the spindle fan should be on.
*** Start "Shopbot 3" program.
*** Open Tools...Spindle RPM Control menu (to allow RPM control)
**** Make sure collet is tightened or no tool or nut is installed
**** Run the C5 warm up routine
** Jogging
*** Keypad
*** Arrow Keys + Page Up, Page Down (ctrl for fast jog)

* CAM Software
** Vectric V Carve
** Just the basics...separate class for advanced V Carve.
** Online videos

* Running your Job
** Zeroing X & Y
*** With machine off slow push gantry towards X0 until it hits hard stops (optional)
*** Turn on big red switch while still holding gantry.
*** Jog machine away from X0 Y0 so machine will find switches
*** Click X, Y zero button.
** Zeroing Z (top of work piece)
*** Jog over your work piece
*** Place Z zero plate on work piece under the bit
*** Place clip on bit
*** Test connection by touching plate to bit and watch for light #1 to light
*** Click the Z 0 button (it will touch off twice!!!)
*** If Z is critical, you may want to verify that your bit has been zeroed properly by using a "MZ,0" command over the surface you have zeroed the bit to. Repeat zeroing if not correct.

* Waste Board and clamping

* Collets, Bits, Feeds and Speeds
** Feeds and Speeds
*** Use a Cut Load Calculator to determine which feeds and speeds you should be using for your specific bits. An overview is avaialble at: [https://groups.google.com/d/msg/pumping-station-one/vUF3iKRQ9yc/_qNnLXzZ3QcJ]
** Collets
*** We currently have collets for 1/2, 1/4, 3/16 and 1/8" shank bits.
*** Try to keep them clean and store them away from dust between uses. Dust between the gaps will produce runout. The drawer mounted under the Shopbot is the right place to store these items.
*** If the collet nuts are not threading smoothly try cleaning the threads with a small brush, spindle threads as well.
** Bits
*** Use bits designed for the material you are cutting. Don't just steal a bits from the Bridgeport. They won't do a good job and will probably overheat.
*** For cutting out things, use the smallest appropriate bit. Using a 1/2" bit to cutout will just create a lot of mess.

* ShopBot should not be used for...
** Metals other than aluminum
** Cutting anything that requires coolant or lubricant (it will ruin the waste board)
** Ripping lumber (use the table saw)
** Thickness Planning (Use the planner if you can)
** Drilling holes with drill bits (a small end mill works better)

* How to leave the machine (be excellent)
** Machine
*** Home the machine to X0, Y0
*** Turn off both switches
*** Remove Key
*** Remove bit and collet.
*** Place both collet wrenches on top of electronics box
*** clean up work area
*** Smooth out waste board if you puckered it at all.
*** Check if the dust collector needs to be emptied

** Post a picture on our [[Blog]] please!

== Use checklist ==

PS1 is experimenting with the use of checklists to encourage the safe use and proper care of tools in the workspace. The latest version of the [[checklists]] for this tool is stored as a [https://docs.google.com/document/d/1zxrvQX0DXaLxaXkaKCKpZ-PAgnDak6ezKKBkdu_Fw1U/edit?usp=sharing Google Doc] that can be edited by anyone. If you make changes, update the effective date at the bottom of the document. Print a new copy, and replace the old one.

Physical checklists are necessarily constrained in length. Following is a more extensive pre-flight checklist:

* Did you home the machine?
* Is the dust collect gate open?
* Are you sure you have the right X, Y orientation for your file and material?
* Did you set the proper X,Y zero for your work piece on the Shopbot.
* Is the correct bit installed and tight?
* Is the key in and turned on?
* Is the dust skirt set right so it does not get smashed.
* Is Z zero set to the work top?
* Are the touch plate and clip returned?
* Is the material properly secured?
* Open the Shopbot spindle control dialog (Tools > Spindle RPM Control)
* Safety glasses, hearing protection on.
* Start the job with the E-Stop ready to hit.
* Turn on dust collector ( I like to wait so I can hear that things sound right on the shopbot before turning on the collector)

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Elizabeth Koprucki
|Danger Committee
|
|-
|Bart Dring
|Danger Committee
|
|-
|Ryan Pierce
|Danger Committee
|
|-
|Nathan Ellis
|Danger Committee
|
|-
|Michael Skilton
|Danger Committee
|
|-
|Arturo Duarte
|Bart
|
|-
|Derek Bever
|Bart
|
|-
|Everett
|Bart
|
|-
|Vincent Colombo
|Bart
|
|-
|[[User:justin|Justin T. Conroy]]
|Bart
|
|-
|Hugh Sato
|Bart
|
|-
|Sergey Nekrasov
|Bart
|
|-
|Valerie Moore
|Bart
|
|-
|Patrick Schless
|Bart
|
|-
|Tom Forajter
|Bart
|
|-
|Todd Allen
|Michael Skilton
|
|-
|[[User:RogerMoore|Roger Moore]]
|Bart
|
|-
|Tim Saylor
|Bart
|
|-
|Hef
|Bart
|
|-
|Jeff McBride
|Bart
|
|-
| Maxwell ?
| Michael Skilton
|
|-
|Samuel Swope
|Michael Skilton
|
|-
| Khoi Nguyen
|Michael Skilton
|
|-
|Brian Chojnowski
|Michael Skilton
|
|-
|Josh Cooper
|Bart
|
|-
|Andrew Camardella
|Bart
|
|-
|Adam Glick
|Bart
|
|-
|Yehuda Braun
|Bart
|
|-
| Jeff Kantarek
| Michael Sklton
|
|-
| Justin Miles
|Michael Skilton
|
|-
|Will Garza
|Michael Skilton
|
|-
|Clarence Risher
|Michael Skilton
|
|-
|[[User:ericbeau|Eric Beauchamp]]
|Michael Skilton
|
|-
|[[User:Jason|Jason]]
|Michael Skilton
|
|-
|Eric Stein
|Bart
|
|-
|Colin Parsons
|Bart
|
|-
|David Ditzler
|Bart
|
|-
|Ray Doeksen
|Bart Dring
|
|-
|Ron Bean
|Khoi Nguyen & Michael Skilton
|
|-
| Thomas Wright
|Khoi Nguyen & Michael Skilton
|
|-
|David Morton
|Bart Dring
|
|-
|Ron Olson
|Bart Dring
|
|-
|Kyle Bieneman
|Bart Dring
|
|-
|[[User:amishhammer|Tom Judge]]
|Michael Skilton
|
|-
|Bryan Gleason
|Michael Skilton
|
|-
|Dave Schact
|Ryan Pierce
|
|-
|Chris Agocs
|Andrew Camardella
|
|-
|[[user:kuroishi | Doorman Dave ]]
|Andrew Camardella
|
|-
|Alec Weege
|Andrew Camardella
|
|-
|Sam Reicks
|Andrew Camardella
|
|-
|Touly Phiachantharath
|Andrew Camardella
|
|-
|Lucas Goossen
|Andrew Camardella
|
|-
|[[user:Tina|Tina C]]
|Andrew Camardella
|
|-
|Ryan Neuman
|Andrew Camardella
|
|-
|Dan Loeser
|Andrew Camardella
|
|-
|Ben Bogler
|Andrew Camardella
|
|-
|Erin Banwell
|Ryan Pierce
|
|-
|Brad Rios
|Ryan Pierce
|
|-
|Aaron Carlock
|Andrew Camardella
|
|-
|James Villalpando
|Andrew Camardella
|
|-
|Connor Jansen
|Andrew Camardella
|
|-
|Tait Leswing
|Bart
|
|-
|Raj Perera
|Khoi Nguyen
|
|-
|Keith Hultman
|Andrew Camardella
|
|-
|David Srebro
|Andrew Camardella
|
|-
|[[user:Wessing | Erik Wessing ]]
|Andrew Camardella
|
|-
|Leeswann Bolden
|Andrew Camardella
|
|-
|Josh Myers
|Andrew Camardella
|
|-
|Kurt Ziegel
|Andrew Camardella
|
|-
|Glenn Powers
|Andrew Camardella
|
|-
|[[User:mqudsi|Mahmoud Al-Qudsi]]
|Andrew Camardella
|
|-
|Casey Olson
|Khoi
|
|-
|Mike Jones
|Andrew Camardella
|
|-
|Aaron Feigen
|Andrew Camardella
|
|-
|Jim Baker
|Andrew Camardella
|
|-
|Eric Reusche
|Khoi Nguyen
|
|-
|Ralph Brendler
|Andrew Camardella
|
|-
|John McDonald
|Andrew Camardella
|
|-
|Alex Al-Hamdan
|Andrew Camardella
|
|-
|Eugene Liokumovich
|Andrew Camardella
|
|-
|Randal Cox
|Andrew Camardella
|
|-
|Simon Pyle
|Andrew Camardella
|
|-
|Jean Michel Crettaz
|Andrew Camardella
|
|-
|Brian Zable
|Andrew Camardella
|
|-
|Daylan Dufelmeier
|Andrew Camardella
|
|-
|Steve Kruse
|Matt Meshulam
|
|-
|Mike Mandrea
|Andrew Camardella
|
|-
|Jeff Zelnio
|Andrew Camardella
|
|-
|Aaron Stoddart
|Matt Meshulam
|
|-
|Koun Park
|Matt Meshulam
|
|-
|Dan Baltudis
|Matt Meshulam
|
|-
|Curtiss Cooke
|Matt Meshulam
|
|-
|Jeannine Chuchan
|Matt Meshulam
|
|-
|Brennan Koziarz
|Matt Meshulam
|
|-
|Brandon Love
|Matt Meshulam
|
|-
|Mike Vitale
|Matt Meshulam
|
|-
|Emma Purola
|Matt Meshulam
|
|-
|Chris Kohl
|Matt Meshulam
|
|-
|Daniel Sojka
|Matt Meshulam
|
|-
|Naguib Azab
|Matt Meshulam
|
|-
|Mark Zumwalt
|Matt Meshulam
|
|-
|Joseph Juhnke
|Andrew Camardella
|
|-
|Alex Berkowitz
|Andrew Camardella
|
|-
|Andy Muhic
|Matt Meshulam
|
|-
|Adam Stein
|Matt Meshulam
|
|-
|John Farmer
|Matt Meshulam
|
|-
|Joshua Havenga
|Matt Meshulam
|
|-
|[[user:mct|McTavish McArdle]]
|Matt Meshulam
|
|-
|Frank Bowles
|Matt Meshulam
|
|-
|Joe Iklov
|Matt Meshulam
|
|-
|Matthew Quigley
|Matt Meshulam
|
|-
|Derwin Umali
|Andrew Camardella
|
|-
|Doug Mahoney
|Matt Meshulam
|
|-
|Rob Robinson
|Matt Meshulam
|
|-
|Dan Sloboda
|Matt Meshulam
|
|-
|Jacob Collins
|Matt Meshulam
|
|-
|Donald Wells
|Matt Meshulam
|
|-
|[[user:jim|Jim Brink]]
|Matt Meshulam
|
|-
|[[user:mkeith|Matt Keith]]
|Matt Meshulam
|
|-
|[[user:vmorris|Victoria Morris]]
|Matt Meshulam
|
|-
|[[user:bobsabayesian|Bob Loos]]
|Matt Meshulam
|
|-
|[[user:muthpete|Peter Muth]]
|Matt Meshulam
|
|-
|[[user:guijemont|Guillaume Emont]]
|Matt Meshulam
|
|-
|[[user:erikthefunk|Erik Funkhouser]]
|Matt Meshulam
|
|-
|[[user:mrashes|Max Rashes]]
|Matt Meshulam
|
|-
|[[user:panchan99|Juan Ramos]]
|Matt Meshulam
|
|-
|[[user:Justjoe|Joe Dowling]]
|Matt Meshulam
|
|-
|[[user:smash|Ashley Matrisciano]]
|Matt Meshulam
|
|-
|Ryan Kapp
|Matt Meshulam
|
|-
|Idris Raja
|Matt Meshulam
|
|-
|[[user:Dannyblanchard|Danny Blanchard]]
|Matt Meshulam
|
|-
|Aaron Mintz
|Matt Meshulam
|
|-
|[[user:ianstubbs|Ian Stubbs]]
|Matt Meshulam
|
|-
|[[user:skynaya|Sky Nova]]
|Matt Meshulam
|
|-
|Chris Ruhland
|Matt Meshulam
|
|-
|[[user:Jaypee|Jay Pee]]
|Matt Meshulam
|
|-
|[[user:Ryanmafi|Ryan Fiebing]]
|Matt Meshulam
|
|-
|[[user:sblaszak|Shawn Blaszak]]
|Matt Meshulam
|
|-
|[[user:tonyiacullo|Tony Iacullo]]
|Matt Meshulam
|
|-
|Mark Haughey
|Matt Meshulam
|
|-
|Chris Iacullo
|Matt Meshulam
|
|-
|Ian Monroe
|Matt Meshulam
|
|-
|Ashish Jasani
|Matt Meshulam
|
|-
|Kurt Gilman
|Matt Meshulam
|
|-
|Abel Greenwald
|Matt Meshulam
|
|-
|Vaidotas (Vai) Staugaitis
|Matt Meshulam
|
|-
|Leo Battikhi
|Matt Meshulam
|
|-
|Matt Schaid
|Matt Meshulam
|
|-
|Jamie Vollmer
|Matt Meshulam
|
|-
|Bhairavi Warke
|Matt Meshulam
|
|-
|Denis Kuznetsov
|Matt Meshulam
|
|-
|Brian Carstensen
|Matt Meshulam
|
|-
|Rob Dumas
|Matt Meshulam
|
|-
|Mark Weiser
|Matt Meshulam
|
|-
|Tom Burtonwood
|Matt Meshulam
|
|-
|Steve Madonna
|Matt Meshulam
|
|-
|Jason Araujo
|Matt Meshulam
|
|-
|Bruce Alan Mace
|Matt Meshulam
|
|-
|Molly Adamski
|Matt Meshulam
|
|-
|Jeremy Shaw
|Matt Meshulam
|
|-
|Sam Chen
|Matt Meshulam
|
|-
|John McBride
|Matt Meshulam
|
|-
|Adomas Tautkus
|Matt Meshulam
|
|-
|Tim Buckley
|Matt Meshulam
|
|-
|Martina Josimovska
|Matt Meshulam
|
|-
|James Jacobs
|Matt Meshulam
|
|-
|George Shaw
|Matt Meshulam
|
|-
|David Earl
|Matt Meshulam
|
|-
|[[User:pedrosk| Eduard Breuer]]
|Matt Meshulam
|
|-|-
|Matthew Kim
|Matt Meshulam
|
|-
|Corey Peoples
|Matt Meshulam
|
|-
|Paul Graham
|Matt Meshulam
|
|-
|Matt Grunstad
|Matt Meshulam
|
|-
|Rolf Scheidt
|Matt Meshulam
|
|-
|Arjun Sharma
|Matt Meshulam
|
|-
|Chris Laurent
|Matt Meshulam
|
|-
|[[User:dwlocks|Dan Locks]]
|Matt Meshulam
|
|-
|Zack Sasnow
|Matt Meshulam
|
|-
|Ben Stringer
|Matt Meshulam
|
|-
|[[User:Ekaj|Jacob Snyder]]
|Matt Meshulam
|8/24/17
|-
|James Beck
|Matt Meshulam
|9/13/17
|-
| Sam Gates
|Matt Meshulam
|10/01/17
|-
| Tommy TBones Cramer
|Matt Meshulam
|09/24/17
|-
| tee
|Matt Meshulam
|10/26/17
|-
|[[User:wittnl|Nathan Witt]]
|Matt Meshulam
|2017-12-09
|-
|[[User:GalaxyCascade|Steve Griegoliet]]
|Matt Meshulam
|12/09/17
|-
| Chinbayar Davaatseren
| Matt Meshulam
| 12/09/17
|-
|Theo T
|David Earl
|1/20/18
|-
|[[User:Frenchy|Jeremie Davis]]
|David Earl
|1/21/18
|-
|Armani Barron
|Matt Meshulam
|9/16/17
|-
|Scott Fullman
|David Earl
|02/24/18
|-
|Michael Donovan
|David Earl
|03/04/2018
|-
|Damon Carrvesco
|David Earl
|03/26/2018
|-
|Ryan Kelly
|David Earl
|03/26/2018
|-
|Will Coffin
|David Earl
|03/26/2018
|-
|Shabab Mustafa
|David Earl
|03/26/2018
|-
|Bruce Mace
|David Earl
|03/26/2018
|-
|Shahnawas Khokhar
|David Earl
|03/26/2018
|-
|Seth Cothron
|David Earl
|04/22/2018
|-
|Matthew Currey
|David Earl
|04/22/2018
|-
|Adam Hall
|David Earl
|04/29/2018
|-
|Kevin Huemann
|David Earl
|04/29/2018
|-
|Donzell Gordon
|David Earl
|04/28/2018
|-
|Nelson Reyes
|David Earl
|05/26/2018
|-
|David DesRoberts
|David Earl
|05/26/2018
|-
|Brendan Fortune
|David Earl
|06/02/2018
|-
|Chris Albert
|David Earl
|06/17/2018
|-
|Nate Myren
|David Earl
|06/23/2018
|-
|Eli Scholssberg
|David Earl
|06/23/2018
|-
|Szymon Mirek
|David Earl
|06/24/2018
|-
|Dan Willmott
|David Earl
|06/24/2018
|-
|Mark Treiber
|David Earl
|10/28/2018
|-
|Charlie Kepner
|David Earl
|02/20/2019
|-
|Kevin Cluff
|David Earl
|02/20/2019
|-
|Greg Bell
|David Earl
|03/23/19
|-
|Paul Ocampo
|David Earl
|03/28/19
|-
|Fritz Sullivan
|David Earl
|03/31/19
|-
|Daniel Gulick
|David Earl
|12/10/2018
|-
|Alex Biardo
|David Earl
|05/07/2019
|-
|Brendan Byrne
|David Earl
|05/07/2019
|-
|Sam Vuchetich
|David Earl
|09/29/2019
|-
-
|Antina Lee
|David Earl
|09/29/2019
|-
-
|Ryan Zoghlin
|David Earl
|1/25/2020
-
|Rob German
|David Earl
|09/29/2019
|-}

If you have been authorized but cannot log in, request to be added to the "ShopBot Authorized" Samba group (send an email to info (at) pumpingstationone.org with your username and the name of the person who certified you) so that your login works. If you don't have a log-in on https://members.pumpingstationone.org/ you will have issues here - sign up on that site first if you haven't already.

= Maintenance =

== Maintenance Log ==
{| class="wikitable" border="1"
!Date
!Preformed by
!Service Type
!Notes
|-
|4/16/2017
|Ryan Pierce
|Created new AutoDesk Fusion 360 Post Processor. Modified Vectric Post Processors.
|Created new Fusion 360 Post Processor. It includes the changes listed below for the Vectric Post Processors. For Vectric, modified the Post Processors so that if the spindle does not spin up, it gives the user a Retry/Cancel dialog box instead of Abort/Retry/Ignore where Ignore is identical to Retry. Also, these Post Processors broke the Preview mode in the ShopBot software because the preview mode did the real spindle check and it failed because, of course, the spindle wasn't running. The new version will ignore the spindle check in preview mode.
|-
|11/8/2014
|Ryan Pierce
|Updated VCarve Post Processor
|Previously, installed new Post Processor to preset an Abort / Retry / Ignore dialog box when the spindle is started but doesn't spin up. Usual culprit is that a job is started when the the interlock is disabled, which results in the non-spinning bit crashing into the workpiece. Abort stops the job. Today, fixed Retry code. If you power on the VFD and the motor start is enabled, the VFD refuses to start. So I've re-programmed the Retry button to stop the VFD, wait 2 seconds, start the VFD, wait 2 more seconds, and check again to see if it is running. The Ignore button actually acts as Retry because we don't want someone clicking through this dialog box and damaging the machine. NOTE: The Aspire PC in the shop also has this Post Processor, but if you use Aspire, VCarve Pro, etc. on your personal computer, you will need the latest Post Processor to support this safety check.
|-
|11/8/2014
|Ryan Pierce
|Updated ShopBot software
|Did upgrade from 3.8.14 to 3.8.26. Installed latest firmware on ShopBot controller. (This was mandatory.) Two features of interest: Fixed occasional erractic behavior after repeated Stops and Resumes (and Nudges or Command Insertions). Reduced liklihood of Keypad lockup.
|-
|5/31/2015
|Ron Olson
|Created new VCarve Post Processors
|For drag/engraving bits, it's important that the spindle be turned '''off''' so as to not destroy the bit. Instead of manually modifying the sbp every time to remove the check that the spindle is turned on, I created a couple of new post processors (inches and mm, similar to Ryan's), that explicitly ''turn off'' the spindle. The user is given two opportunities to cancel the job if that is not what he/she wants.
|-
|}

== Outstanding Maintenance Issues ==

=== Lack of True E-Stop ===
As shipped, the ShopBot PRS does not support an Emergency Stop. This could be hacked, but it runs the risk of damaging the machine if engaged in a non-emergency situation. Suggested solution: Installing a 10A double pole 24V coil DIN mount relay, and powering the coil via the 24V supply through a normally closed E-Stop button. One pole will disconnect the 63V stepper motor current. One pole will break the control signal that enables the VFD and will cause the VFD to brake to a stop.

=== Automatic Dust Collection ===
The ShopBot has +5V TTL outputs that could be used to trigger automatic dust collection (when the spindle goes live) and/or a warning light (when the gantry is enabled to move.)

=== Limit Switch Issues ===
Every time you start the ShopBot, it resets itself so that the limit switches are disabled! You can turn them on (if memory serves) with the Values -> Input Switch Assignment menu item. Limit switches are really useful - but they need to be enabled. When they are, they will stop manual jogging when the limit is hit (although pressing the key again will let you continue moving the gantry) and they will also stop a running job (but give you the option of ignoring the limits.)

I found a couple more problems when testing all the limits. When I took the gantry to X maximum, the dust collector hose pulled off! I put it back on, but I'm not sure how stable this is. Also, when I originally set the Y maximum and minimum, I wanted as much spindle travel as possible. But it appears that if you're at the Y max and move in the X direction, you can hit the middle support with the dust collector boot. We've got several inches Y travel beyond the nominal 48", so we may want to look into reducing this to clear the supports.

== Resources ==
[[File:ShopBot PSOne Post Processors.zip]] - Post Processors for Vectric Aspire and VCarve Pro 8.0 which includes the change to check that the spindle actually started.

[[File:ShopBot_TC_PS1-NO-SPIN.zip]] - Post Processors for Vectric Aspire and VCarve Pro which include changes to explicitly *disable* spinning

[[File:ShopBot PSOne Fusion 360 Post Processor.zip]] - Post Processor for Autodesk Fusion 360 which includes the change to check that the spindle actually started.

[[Category:Fabrication]]
[[Category:CNC]]
[[Category:Future Things Bus Data Sources]]

Drill Press Craftsman 20in woodshop

2020-01-18T23:16:34Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner= PS:One
|model=
|serial=
|arrived=
|doesitwork=yes
|contact=[[user: ericbeau|Eric Beauchamp]]
|where=Wood Shop
|certification=yes
|hackable=no
|value=$500
|image=Craftsman20Drill.jpg
|hostarea=Wood Shop
}}

The Craftsman 20" drill press is the primary drill press in the wood shop. Authorization is included in the general wood shop authorization. For upcoming authorizations, see the [https://pumpingstationone.org/events/ calendar].

== Safety ==
The [[:file:Craftsman20_drill_manual.pdf|user manual is available here]].

==Maintenance==
Per the [[:file:Craftsman20 drill manual.pdf|user manual]], the drill should be periodically cleaned of dust, the table wiped with wax to prevent rust, and (if needed) the quill lubricated with a dry lubricant like silicone or graphite. Users should perform this maintenance as the drill is used, and PS1 should inspect the drill monthly.

===Maintenance history===

* '''July 10, 2017.''' Drill press motor is not fully connected. Belt may be rubbing on the housing.
* '''July 14, 2017.''' One of the two posts that adjusts the motor position is missing its nut. Also, there is a rack-and-pinion lever that moves the motor in and out, and one of the posts had skipped a tooth. I worked it back into position, and I believe it is now safe to use, despite the missing nut. Replacing the nut will require removing the motor, which is a two-person job.
* '''July 18, 2017.''' This is fixed now. For the record, the missing nut was M12-1.75. I put some "purple" locktite on both nuts, so hopefully we won't have to take it apart again.

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Eric Beauchamp
|Danger committee
|
|-
| [[User:andrewvaughan|Andrew Vaughan]]
| Andy Larkin
| April 26, 2017
|-
|Paul McClay
|Ralph Brendler
|5/18/17
|-
|Jim Handley
|Ralph Brendler
|5/13/17
|-
|[[User:spektre1|Danielle MacDonald]]
|Ralph Brendler
|2017-06-29
|-
|Christophe Laurent
|Ralph Brendler
|8/10/17
|-
|Sam Yi
|Ralph Brendler
|7/27/17
|-
|Zack Sasnow
|Paul Van Lake
|8/3/17
|-
|Arjun Sharma
|Ralph Brendler
|8.10.17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|Sam Dreyer
|Ralph Brendler
|8/30/17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Tee
|Paul V
|11/09/17
|--
|-
|Nick Fera
|Paul V
|11/09/17
|--
|[[User:frenchy|Jeremie Davis]]
|Ralph Brendler
|11/16/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Jeff Hassberger
|Ralph Brendler
|
|-
|Mac MacDevitt
|Paul V
|12/7/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Jamin Nollsch
|Ralph Brendler
|12/28/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brendler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Scott Fullman
|Ralph Brendler
|2/8/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Nick Prorok
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|Wayne Warren
|Ralph Brendler
|3/22/18
|-
|Adam Hall
|Paul V
|3/29/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Matt Maggio
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|4/19/18
|-}
|Gary Newhouse
|Ralph Brendler
|4/26/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
|John Burkholder
|Ralph Brendler
|5/03/18
|-
| Wayne Hendryx
| Chris Iacullo
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Chris Niziolek
| Ralph Brendler
| 6/14/18
|-
| Sam Wallinga
| Ralph Brendler
| 6/14/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Eli Schlossberg
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Bruce Levin
| Paul V
| 7/05/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Kathryn Connolly
| Paul V
| 7/19/18
|-
| Sam Lewis
| Paul V
| 7/19/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Earl Wood
| Paul V
| 9/13/18
|-
| Jacob Dawson
| Paul V
| 9/13/18
|-
| Ryan Treacy
| Paul V
| 9/20/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Tim Bielawa
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
| Landon Smith
| Ralph Brendler
| 10/18/18
|-
| Will Brown
| Ralph Brendler
| 10/31/18
|-
|Deanna Musurlian
|Ralph Brendler
|01/24/19
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
|Tony Green
|Ralph Brendler
|02/07/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Zach Graceffa
|Ralph Brendler
|04/18/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|David Pfeffer
|Paul V
|05/24/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Sarah Lu
|Ralph Brendler
|07/25/19
|-
|Joseph Kardia
|Ralph Brendler
|08/01/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Hara Kumaran
|David Earl
|08/18/19
|-
|Mike Thompson
|Michelle DeLeon
|08/22/19
|-
|Denise Allen
|Paul V
|08/29/19
|-
|Sam Vuchetich
|Ralph Brendler
|09/05/19
|-
|Miles Hosanna
|Ralph Brendler
|09/19/2019
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|Adam Rangwala
|Ralph Brendler
|11/14/2019
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|Ryan Zoghlin
|Paul V
|1/16/2020
|-
|David Robbins
|Paul V
|1/16/2020
|}
[[Category:Shop Equipment]]
[[Category:Wood Shop]]

Sander (oscillating spindle) - Steel City

2020-01-18T23:15:46Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = No
|model = Steel City Tool Works 55200 Oscillating Spindle Sander
|serial = SERIAL NUMBER
|arrived = ?
|doesitwork = yes
|contact = Eric Beauchamp
|where = Sanding and routing area south wall
|value = $900 ??
|hostarea = Wood Shop
|image = SC spindle sanderL.jpg
}}

== NOTE ==
Eric has diagnosed and ordered parts Sept 2018

Fixed it but then oscillating function failed in spring 2019 again. Usable as spindle

12/7/2019 table unstable need to diagnose

= Maintenance =

== Maintenance Log ==
{| class="wikitable" border="1"
!Date
!Preformed by
!Service Type
!Notes
|-
|8/2018
|EB
|stopped oscillating.
|EB fixed december.
|-
|jan 2 2019
| Zac and gary
|stopped oscillating again.
|
|-
|}

== Outstanding Maintenance Issues ==

=== gearbox being repaired FIXED nov or dec? 2018 broken again jan 2019

== Rules ==

# If you break something, or damage the tool, contact the area host immediately. Don't let others do more damage to the machine, ruin their work, or hurt themselves by using a broken tool.
# Always vacuum the machine, cutting area, and the table around the machine when you are done.

== Documentation ==
* manual [https://images.homedepot-static.com/catalog/pdfImages/e4/e433b76b-3318-46e6-a1a2-f25f5606431e.pdf]

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|<please add>
|<please add>
|-
|gary newhouse
|Eric Beauchamp
|4/26/18
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|David Robbins
|Paul V
|1/16/2020
|-
|Ryan Zoghlin
|Paul V
|1/16/2020
|}

[[Category:Shop Equipment]]
[[Category:Wood Shop]]

Supermax 25x2 Drum Sander

2020-01-18T23:15:15Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner=PS:One
|model=25x2
|serial=?
|arrived=
|doesitwork=no
|contact=[[user: ericbeau|Eric Beauchamp]]
|where=Wood Shop
|certification=yes
|hackable=no
|value=$2700
|image=SupermaxSander.jpg
|hostarea=Wood Shop
}}

== Status ==
Aug 30 2018 Eric B installed new motor and starter capacitor..
'''
DO NOT OPEN HOOD''' to push start as we did in recent past. Just push start button and adjust feed speed.

Stay tuned for more detailed instructions for use.

12/7/2019 feed conveyor belt is destroyed. quite worn belt was running off center and tore itself apart. replacement being ordered.

== Authorization ==

Authorization required. Part of the WoodShop overall authorization. See the PS1 calendar for future dates.

== Usage Notes ==

*For oily or dense woods (tropical hardwoods, etc), take only very light passes to prevent clogging the sandpaper.

*Use a belt cleaner occasionally to refresh the sandpaper

== Safety ==

This sander features overload detection. If the machine detects too high a load, it will automatically slow down the feed. This saves wear and tear on the machine, but may cause burning of the workpiece if you cut too aggressively.

*The height adjustment on this machine is VERY aggressive. A full turn will raise the table by more than 2mm (a typical cut should be < .5mm). '''PLEASE USE A MAXIMUM OF 1/8 TURN OF THE HEIGHT WHEEL PER PASS!'''

* Make your first cuts with a very slow speed (10 or less). Once you are sure the load is OK you can gradually increase the speed on subsequent passes.

*When overload detection kicks in, a red light next to the speed control will turn on. '''IF YOU SEE THIS LIGHT, PLEASE REDUCE YOUR DEPTH OF CUT AND/OR FEED RATE!'''

*Like all of our other sanders, sleeves must be above the elbow, and no gloves should be worn. It's pretty easy to get pulled into the rollers.

== Description ==

* Sanding Capacity:
** Maximum Width (in): 25
** Minimum Length (in): 3-1/2
** Minimum Thickness (in): 1/32
* Drum Speed: 1740 RPM
* Dust Hood: 1000 CFM recommended

==External Links==

*[http://www.supermaxtools.com/products/wood/25x2-double-drum-sander Manufacturer's Page]
*[http://www.supermaxtools.com/wp-content/uploads/25x2_37x2-10-2015.pdf Owner's Manual]

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date}
|-
|Eric Beauchamp
|Danger committee
|6/23/2017
|-
|Ralph Brendler
|Danger committee
|6/23/2017
|-
|Paul van Lake
|Danger committee
|6/23/2017
|-
|Zack Sasnow
|Jason Shanfield
|8/27/17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|Jared K
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brandler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Michael Ice
|Ralph Brendler
|2/08/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Rolf Scheidt
|Ralph Brendler
|2/22/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Nick Prorok
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|[[User:waynr|Wayne Warren]]
|Ralph Brendler
|3/22/18
|-
|Adam Hall
|Paul V
|3/29/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|4/19/18
|-
|4/19/18|Gary Newhouse
|Ralph Brendler
|4/26/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
| Wayne Hendryx
| Ralph Brendler
| 4/19/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Sam Wallinga
| Ralph Brendler
| 6/14/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Eli Schlossberg
| Ralph Brendler
| 6/14/18
|-
| Tyler Works
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Bruce Levin
| Paul V4
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Kathryn Connolly
| Paul V
| 7/19/18
|-
| Sam Lewis
| Paul V
| 7/19/18
|-
| Sam Paris
| Ralph Brendler
| 9/2/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
| Will Brown
| Ralph Brendler
| 10/31/18
|-
|Tatjana Paunesku (tpaune)
|Ralph Brendler
|11/29/18
|-
|Jim Lund
|Paul Van Lake
|12/7/18
|-
|Deanna Musurlian
|Ralph Brendler
|01/24/19
|-
|Pat Hillegass
|Ralph Brendler
|1/24/19
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Kevin Schwartzenberg
|Paul Van Lake
|03/01/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|Zach Graceffa
|Ralph Brendler
|4/18/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|Jack Gibbons
|Paul V
|06/20/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Patrick Cook
|Ralph Brendler
|07/11/19
|-
|Patrick Cook
|Ralph Brendler
|07/11/19
|-
|Nathan Upchurch
|Ralph Brendler
|07/11/19
|-
|Andrew Soghigian
|Ralph Brendler
|07/11/19
|-
|Luke Krudwig
|Ralph Brendler
|07/11/19
|-
|Paul Ocampo
|Ralph Brendler
|07/11/19
|-
|Sarah Lu
|Ralph Brendler
|07/25/19
|-
|Joseph Kardia
|Ralph Brendler
|08/01/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Connar Rosebraugh
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Steven Rummelhoff
|Ralph Brendler
|08/22/19
|-
|Denise Allen
|Paul V
|08/29/19
|-
|Sam Vuchetich
|Ralph Brendler
|09/05/19
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|Adam Rangwala
|Ralph Brendler
|11/14/19
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Adam Keim
|Ralph Brendler
|11/14/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Ryan Zoghlin
|Paul V
|1/16/2020
|-
|David Robbins
|Paul V
|1/16/2020
|}
[[Category:Shop Equipment]]
[[Category:Wood Shop]]

Dayton 6x9 Belt Sander

2020-01-18T23:14:44Z

Rfoto: /* List of Currently Certified Users */

{{Template:EquipmentPage
|owner=PS:One
|model=
|serial=
|arrived=
|doesitwork=no
|contact=[[user: ericbeau|Eric Beauchamp]]
|where= Removed
|certification=yes
|hackable=no
|value=$500
|image=DaytonSander.jpg
|hostarea=Wood Shop
}}

== Notes ==
Dec 31 2018 Disk side guard, table and disk plate removed
== Safety ==

==maintenance==
[[Dayton_6x9_Belt_Sander_maintenance| maintenance page]]

[[Category:Shop Equipment]]
[[Category:Wood Shop]]

= List of Currently Certified Users =
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Eric Beauchamp
|Danger committee
|
|-
|Paul McClay
|Ralph Brendler
|5/18/17
|-
|Jim Handley
|Ralph Brendler
|5/13/17
|-
|Justin Pestka
|Ralph Brendler
|8/30/17
|-
|Danielle MacDonald||Ralph Brendler||2017-06-29
|-
|Zack Sasnow
|Paul Van Lake
|8/3/17
|-
|Arjun Sharma
|Ralph Brendler
|8.10.17
|-
|Sam Dreyer
|Ralph Brendler
|8/30/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Chinbayar Davaatseren
|Ralph Brendler
|11/2/17
|-
|Jeff Hassberger
|Ralph Brendler
|11/2/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brendler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-}
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|Adam Hall
|Paul V
|3/29/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Gary Newhouse
|Eric Beauchamp
|4/26/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
|John Burkholder
|Ralph Brendler
|5/03/18
|-
| Wayne Hendryx
| Chris Iacullo
| 4/19/18
|-
| Chris Niziolek
| Ralph Brendler
| 6/14/18
|-
| Sam Wallinga
| Ralph Brendler
| 6/14/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
|Jim Lund
|Paul Van Lake
|12/7/18
|-
|Michael Baker
|Paul V
|7/18/2019
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Mike Thompson
|Michelle DeLeon
|08/22/19
|-
|Miles Hosanna
|Ralph Brendler
|09/19/2019
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Ryan Zoghlin
|Paul V
|1/16/2020
|}

Router Table (was Excalibur)

2020-01-18T23:14:00Z

Rfoto: /* List of Currently Certified Users */

== Router ==

{{Template:EquipmentPage
| image = Excalibur.jpg
|owner = PS:One
|serial =
|certification = yes
|hackable = no
|model =
|arrived =
|doesitwork = yes
|contact =
|where = Wood Shop
|hostarea = Wood Shop
|value =
}}

'''This tool requires authorization for use.'''

Excalibur Router Table <br>
http://www.general.ca/products/2_excalibur/40-200.html

manual: [[File:Excalibur_router_manual.pdf]]

Porter-Cable 7518 router

Dec 11 2018. installed digitally controlled elevator mechanism.
it is a Nextwave Ready2Rout system https://www.nextwaveautomation.com/shop/READY2LIFT%C2%AE-COMPUTERIZED-ROUTER-LIFT-p114869879

the full system manual for the Ready2Rout is here with a section on how the control panel works
https://docs.wixstatic.com/ugd/59d161_bc5568e32f0848b481e9d3f2409be158.pdf

{{WoodshopProctors}}

== List of Currently Certified Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date Certified}
|-
|Keon Turner
|Ron Olson
|10/19/15
|-
|Marcin Ignasiak
|Eric Beauchamp
|
|-
|Tim Saylor
|Danger Committee
|
|-
|Dillon Gray
|Danger Committee
|
|-
|Shawn Blaszak
|
|
|-
|Adrianna McKinley
|Tim Saylor
|
|-
|Kathy Whisler
|Tim Saylor
|
|-
|James Longfield
|Tim Saylor
|
|-
|Eric Veggeberg
|Tim Saylor
|
|-
| Madeleine Klichowski
| Tim Saylor
|
|-
| Lyn Cole
| Tim Saylor
|
|-
| Nathan Becka
| Tim Saylor
|
|-
| Brian Carstensen
| Tim Saylor
|
|-
| Matt Triano
| Tim Saylor
|
|-
|Bryan Gleason
|Matt Triano
|
|-
|Daniel Wells
|Matt Triano
|
|-
|Sean Corbett
|Matt Triano
|
|-
|Michael Skilton
|Matt Triano
|
|-
|Aaron Feigen
|Matt Triano
|
|-
|Ryan Pierce
|Dan Locks
|
|-
|John Godwim
|Matt Triano
|
|-
|Nate Hutchins
|Matt Triano
|
|-
|Jeff Molek
|Matt Triano
|
|-
|Sloan Lavery
|Matt Triano
|
|-
|Trey Keifer
|Matt Triano
|
|-
|Juan Robles
|Matt Triano
|
|-
|Simon Cygielski
|Matt Triano
|
|-
|Tom Forajter
|Matt Triano
|
|-
|Robert Grossman
|Matt Triano
|
|-
|Lucas Morris
|Matt Triano
|
|-
|Sergio Preston
|Matt Triano
|
|-
|Ron Bean
|Matt Triano
|
|-
|Greg Eagel
|Matt Triano
|
|-
|Carter Constana
|Matt Triano
|
|-
|Adam Glick
|Matt Triano
|
|-
|Zachary Fietsch
|Matt Triano
|
|-
|Solomon Hursey
|Matt Triano
|
|-
|Jesse Reynolds
|Matt Triano
|
|-
|Eduard Shlahtichman
|Matt Triano
|
|-
|Skittles Rainbow
|Matt Triano
|
|-
|Tom Jurgensen
|Matt Triano
|
|-
|Barmey Ung
|Matt Triano
|
|-
|Casey Olson
|Matt Triano
|
|-
|Jonathan Bisson
|Matt Triano
|
|-
|Bandit Gangwere
|Matt Triano
|
|-
|Joseph Nudell
|Matt Triano
|
|-
|David Butler
|Matt Triano
|
|-
|Kathryn Smiley
|Matt Triano
|
|-
|Aimee Spevak
|Matt Triano
|
|-
|Cassie Webster
|Matt Triano
|
|-
|Chris Moylan
|Matt Triano
|
|-
|Mike O'Connor
|Matt Triano
|
|-
|Tyler Hsu
|Matt Triano
|
|-
|Dee Newcum
|Matt Triano
|
|-
|Zihe "Johnson" Luo
|Matt Triano
|
|-
|Giovanni Arroyo
|Matt Triano
|
|-
|Nathan Ellis
|Matt Triano
|
|-
|Ian McLeod
|Nathan Ellis
|
|-
|Brandon Price
|Matt Triano
|
|-
|Arturo Duarte
|Matt Triano
|
|-
|Eric Braun
|Matt Triano
|
|-
|Jeremy Fay
|Matt Triano
|
|-
|Leeswann Bolden
|Matt Triano
|
|-
|James Porter
|Matt Triano
|
|-
|Jeff McBride
|Matt Triano
|
|-
|Connor Miller
|Matt Triano
|
|-
|Ashley Duca
|Matt Triano
|
|-
|Karen Niemczyk
|Matt Triano
|
|-
|Bassam Alshammari
|Matt Triano
|
|-
|John Fiene
|Matt Triano
|
|-
|Thomas Wright
|Matt Triano
|
|-
|Joseph Peltier
|Matt Triano
|
|-
|Justin Conroy
|Matt Triano
|
|-
|David Koppel
|Matt Triano
|
|-
|Sevin Straus
|Matt Triano
|
|-
|Roger Moore
|Matt Triano
|
|-
|Valerie Moore
|Matt Triano
|
|-
|Andy Schwartz
|Matt Triano
|
|-
|Assaf Evron
|Matt Triano
|
|-
|David Pelot
|Matt Triano
|
|-
|Rich Smith
|Matt Triano
|
|-
|Khoi Nguyen
|Matt Triano
|
|-
|Brian Keehner
|Matt Triano
|
|-
|Jesse Gare
|Matt Triano
|
|-
|Tyler Natoli
|Matt Triano
|
|-
|David Siegfried
|Matt Triano
|
|-
|Annie Zebula
|Matt Triano
|
|-
|Eliya Gwetta
|Matt Triano
|
|-
|Patrick Schliss
|Matt Triano
|
|-
|Arjun Wadnerkar
|Matt Triano
|
|-
|Touly Phiachantharath
|Matt Triano
|
|-
|Matt Vibberts
|Matt Triano
|
|-
|Thomas Garza
|Matt Triano
|
|-
|Will Garza
|Matt Triano
|
|-
|Brennan Koziarz
|Matt Triano
|
|-
|Alec Weege
|Matt Triano
|
|-
|Eric Beauchamp
|Matt Triano
|
|-
|Clarence Risher
|Matt Triano
|
|-
|Erica Tesla
|Matt Triano
|
|-
|Jabu Dawdu
|Matt Triano
|
|-
|Karen Murphey
|Matt Triano
|
|-
|Matt Meshulam
|Matt Triano
|
|-
|Josh Myers
|Matt Triano
|
|-
|Weston Tanner
|Matt Triano
|
|-
|Hugh Sato
|Matt Triano
|
|-
|Nora Sluzas
|Matt Triano
|
|-
|Elizabeth Koprucki
|Matt Triano
|
|-
|Oscar Villareal
|Matt Triano
|
|-
|Rob Paral
|Matt Triano
|
|-
|Alex Schaffer
|Matt Triano
|
|-
|Szymon Sambor
|Matt Triano
|
|-
|Michael Solhelm
|Matt Triano
|
|-
|[[User:lucas|Lucas Goossen]]
|Matt Triano
|
|-
|[[User:Mwilkens|Matt Wilkens]]
|Matt Triano
|
|-
|Eric Slehofer
|Matt Triano
|
|-
|Jon Levine
|Matt Triano
|
|-
|Melody Snyder
|Matt Triano
|
|-
|Curtis Cooke
|Matt Triano
|
|-
|Harry Morgan
|Matt Triano
|
|-
|Sam Drazin
|Matt Triano
|
|-
|Mike Kislovsky
|Matt Triano
|
|-
|Keven Kalay
|Matt Triano
|
|-
|Sam Reicks
|Ron Olson
|
|-
|Kevin Pulver
|Ron Olson
|
|-
|Cary Lahucik
|Ron Olson
|
|-
|Keith Hultman
|Ron Olson
|
|-
|Mario Rodriguez
|Ron Olson
|
|-
|John Keippel
|Ron Olson
|
|-
|Szilvia Precsinszki
|Ron Olson
|
|-
|Davis Mazariegos
|Ron Olson
|
|-
|Pete Noverini
|Matt Triano
|
|-
|Mike Coriale
|Matt Triano
|
|-
|Dan Baltudis
|Ron Olson
|
|-
|David Fell
|Ron Olson
|
|-
|Dubi Kaufmann
|Ron Olson
|
|-
|Patrick Grider
|Ron Olson
|
|-
|Tyler Matthew
|Matt Triano
|
|-
|Shae Kurko
|Matt Triano
|
|-
|John Farmer
|Ron Olson
|
|-
|Sam Paris
|Ron Olson
|
|-
|Frances Ritchie
|Ron Olson
|
|-
|Ben Kern
|Ron Olson
|
|-
|Eric Yu
|Ron Olson
|
|-
|Knute Martell
|Ron Olson
|
|-
|Karol Slowikowski
|Ron Olson
|
|-
|Chris Smith
|Ron Olson
|
|-
|Benjamin Miller
|Ron Olson
|
|-
|Jennie P
|Ron Olson
|
|-
|Eugene Liokumovich
|Ron Olson
|
|-
|Laurel Garrett
|Matt Triano
|
|-
|Rei Kevin
|Matt Triano
|
|-
|Aji Slater
|Matt Triano
|
|-
|John Beyer
|Matt Triano
|
|-
|Brad Topol
|Matt Triano
|
|-
|[[User:papaben44|Benjamin Dambman]]
|Matt Triano
|4/14/2015
|-
|Tomas Ward
|Ron Olson
|4/26/2015
|-
|Les Schier
|Jason Shanfield
|5/2/15
|-
|Andy Richardson
|Matt Triano
|4/14/15
|-
|Erik Wessing
|Eric Beauchamp
|
|-
|Ray Doeksen
|Eric Beauchamp
|
|-
|Ryan Neuman
|Ron Olson
|
|-
|Anthony Phelps
|Eric Beauchamp
|8/27/2015
|-
|Ralph Brendler
|Eric Beauchamp
|8/27/2015
|-
|Jim Baker
|Eric Beauchamp
|8/27/2015
|-
|Kyle Bieneman
|Ron Olson
|
|-
|Glenn Powers
|Jason Shanfield
|10/18/2015
|-
|Niko Hawley
|Eric Beauchamp
|
|-
|Kevin Mitchell
|Eric Beauchamp
|
|-
|[[User:themoffatt|Adam Moffatt]]
|Eric Beauchamp
|10/22/2015
|-
|Jean Michel Crettaz
|Eric Beauchamp
|10/22/2015
|-
|Caleb Young
|Eric Beauchamp
|
|-
|Peter Letscher
|Eric Beauchamp
|11/05/15
|-
|Glenn Trussell
|Eric Beauchamp
|11/05/2015
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Shine Chen
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/03/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Chris Kohl
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Peter Brask
|Eric Beauchamp
|1/14/16
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
|Shelly Loke-Gayares
|Eric Beauchamp
|1/14/16
|-
|Christopher Carson
|Eric Beauchamp
|2/25/16
|-
|Jared K
|Andy L
|3/03/16
|-
|Brian Cuocci
|Andy L
|3/17/16
|-
|Julie Zwolinski
|Eric Beauchamp
|3/24/16
|-
|Nick Puglisi
|Eric Beauchamp
|4/21/16
|-
|Andy Muhic
|Andy Larkin
|4/28/16
|-
|Colin Campbell
|Andy L
|5/5/16
|-
|Hans Griese
|Andy Larkin
|5/5/16
|-
|Spencer Simms
|Eric Beauchamp
|05/19/2016
|-
|Josh Younger
|Eric Beauchamp
|5/19/16
|-
|Ian Monroe
|Eric Beauchamp
|5/19/16
|-
|Joseph Juhnke
|Eric Beauchamp
|6/20/16
|-
|Donald Wells
|Andy Larkin
|8/4/16
|-
|An Phan
|Andy Larkin
|7/7/16
|-
|Derwin Umali
|Andy Larkin
|8/4/16
|-
|Simon Pyle
|Andy Larkin
|
|-
|Max Rashes
|Ken Burkhardt
|9/20/16
|-
|Logan Price
|Andy Larkin
|11/21/16
|-
|Kris Blouch
|Andy Larkin
|11/21/16
|-
|Tony Iacullo
|Andy
|12/5/16
|-
|Matt Schaid
|Andy Larkin
|01/05/17
|-
|Jamie Vollmer
|Andy Larkin
|01/05/17
|-
|Chris Ruhland
|Andy Larkin
|01/05/17
|-
|John McBride
|Andy Larkin
|01/19/17
|-
|Will Heil
|Andy Larkin
|01/19/17
|-
|Dusty Buyck
|Andy Larkin
|01/19/17
|-
|Ashley Borg
|Andy Larkin
|4/13/17
|-
| [[User:Andrewvaughan|Andrew Vaughan]]
| Andy Larkin
| 2017-04-25
|-
|Molly Adamski
|Ralph Brendler
|4/27/17
|-
|Shabab Mustafa
|Ralph Brendler
|4/27/17
|-
|Brett Sanderson
|Ralph Brendler
|4/27/17
|-
|Crystal Zapata
|Ralph Brendler
|4/27/17
|-
|Alexa Viscius
|Ralph Brendler
|4/27/17
|-
|David Earl
|Ralph Brendler
|5/4/2017
|-
|Paul McClay
|Ralph Brendler
|5/18/17
|-
|Kari Danek
|Ralph Brendler
|6/16/17
|-
| [[User:spektre1|Danielle MacDonald]]
| Ralph Brendler
| 2017-06-29
|-
|Zack Sasnow
|Paul Van Lake
|8/3/17
|-
|Arjun Sharma
|Ralph Brendler
|8.10.17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|Sam Dreyer
|Ralph Brendler
|8/30/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
|Mike Thariath
|Ralph Brendler
|10/19/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Tee
|Paul V
|11/09/17
|--
|-
|Nick Fera
|Paul V
|11/09/17
|--
|[[User:frenchy|Jeremie Davis]]
|Ralph Brendler
|11/16/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Corey TOyama
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Jeff Hassberger
|Ralph Brendler
|11/2/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Jamin Nollsch
|Ralph Brendler
|12/28/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brendler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Michael Ice
|Ralph Brendler
|2/08/18
|-
|Scott Fullman
|Ralph Brendler
|2/08/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Rolf Scheidt
|Ralph Brendler
|2/22/18
|-}
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|[[User:waynr|Wayne Warren]]
|Ralph Brendler
|3/22/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Matt Maggio
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|4/19/18
|-
| Wayne Hendryx
| Chris Iacullo
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Fritz Sullivan
| Ralph Brendler
| 5/30/18
|-
| Elizabeth Reuter
| Ralph Brendler
| 5/30/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Chris Niziolek
| Ralph Brendler
| 6/14/18
|-
| Sam Wallinga
| Ralph Brendler
| 6/14/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Eli Schlossberg
| Ralph Brendler
| 6/14/18
|-
| Tyler Works
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Adam Wilk
| Ralph Brendler
| 7/26/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
| Will Brown
| Ralph Brendler
| 10/31/18
|-
|Tatjana Paunesku (tpaune)
|Ralph Brendler
|11/29/18
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Kevin Schwartzenberg
|Paul Van Lake
|03/01/19
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
| Tony Green
| Ralph Brendler
| 02/07/19
|-
|Bobby Salazar
|Ralph Brendler
|03/21/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|Zach Graceffa
|Ralph Brendler
|04/18/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Nathan Upchurch
|Ralph Brendler
|07/11/19
|-
|Luke Krudwig
|Ralph Brendler
|07/11/19
|-
|Andrew Soghigian
|Ralph Brendler
|07/11/19
|-
|Paul Ocampo
|Ralph Brendler
|07/11/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Joseph Kardia
|Ralph Brendler
|08/01/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Hara Kumaran
|David Earl
|08/18/19
|-
|Steven Rummelhoff
|Ralph Brendler
|08/22/19
|-
|Mike Thompson
|Michelle DeLeon
|08/22/19
|-
|Denise Allen
|Paul V
|08/29/19
|-
|Sam Vuchetich
|Ralph Brendler
|09/05/19
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|Drew Deitch
|Paul V
|10/17/19
|-
|Nikolas Gamarra
|Ralph Brendler
|10/13/19
|-
|Adam Rangwala
|Ralph Brendler
|11/14/19
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|David Robbins
|Paul V
|1/16/2020
|-
|Ryan Zoghlin
|Paul V
|1/16/2020
|}
[[Category:Shop Equipment]]
[[Category:Fabrication]]
[[Category:Wood Shop]]

SawStop table saw

2020-01-18T23:13:17Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|certification=yes
|hackable = NO
|model = Model PCS31230 3.0HP 220V
|serial = P114010835
|arrived = 9/1/2012
|doesitwork = yes
|contact = Wood Shop Area Host
|where = Wood Shop
|value = $3,000.00
|image = SawStop.jpg
|hostarea = Wood Shop
}}
[[File:Saw stop badge.jpg|thumb|right|200px]]

= Authorization for this tool by authorized proctors only =
== Authorized Proctors ==
{| class="wikitable" border="1"
|-
|Ron Olson
|-
|Eric Beauchamp
|-
|Ralph Brendler
|-
|Paul VanLake
|-
|Michelle DeLeon
|}

== Status ==

Repaired and in working order as of 11/9/2015

oops on 9/30/2018, someone reported on googlegroups that Chalkpaper on ply wood caused the brake to engage..

10-5-18 reports of Elevator not working

Repaired and in working order as of 11/9/2015

may 14 2018 brake triggered by lasered wood

june 16 2018 tilt broken

Repaired--9/30/2018, someone reported on googlegroups that Chalkpaper on ply wood caused the brake to engage..

7/1/2018 tilt broken

10-5-18 tilt and Elevator not working Parts ordered.

10/24/2018 everything put back together and the lift and tilt mechanisms work mostly like a charm.still waiting for pinion gear to optimize it, but is again functional..

11-17-2018 repaired. 11/16/2018. Brake tripped by user holding a graphite pen in hand while running saw. Pencil made blade contact with blade

2/12/2019. Ashley ordered and David E replaces brake and blade. 2/11/2019. bladeBrake tripped again new on order

3/3/2019. David earl repaired finniky switch. Repaired / adjusted spring and it’s mounts, re-mounted loose control PCB

4/7/2019. Elevator not working 4/9/2019 Eric repaired. Still a little hard to turn but working. 8/24. Brake engaged. Out of service

8/25/19. Saw is back in service. The dado stack will be out until we received the replacement brake

9/14/19. The angle adjustment is not working.
It is at 5 degrees currently and when trying to turn it, the gears sort of clunk and sets it back at 5. —david p.

9/16/19 working ok today thanks to whoever fixed it gary

10/26/19 Eric replaced brake

11/11/2019 Tilt mechanism broken DO NOT TILT BLADE. Gear stripped. Saw still usable in 90 degree cuts.

== How to Become an Authorized Proctor ==

Contact Wood Shop Area Host Eric Beauchamp.

= Rules =
# Do not move the machine ever.
# Never use the table as a work surface.
# Always have the dust collection on. Turn it on before you plug in the saw and off after you unplug the saw.
# Always check your material on the blade before you spin up the blade. If the light turns red, DO NOT CUT.
# Always check your wood for nails or staples. If you're not sure, check the entire piece with a magnet.
# If you break something, or damage the saw, contact the area host immediately. Don't let others do more damage or hurt themselves by using a broken tool.
# Always dust the entire machine when you are done. Also check the motor compartment after every use and vacuum out as needed.

= Additional Information =

== Dado Stack ==
Dado stack use requires separate authorization.

SawStop saws support 8″ dado sets only. The optional dado brake cartridge must be used for dado cuts. It has a larger brake pawl designed to stop the multiple blades in a dado set. In addition, you will also need to use a zero-clearance insert specifically for the dado set.

http://www.rockler.com/sawstop-dado-brake-cartridge-for-cns-table-saws

== Sacrificial Fence ==

The Sacrificial Fence requires the dado stack authorization to have been completed.

A sacrificial fence is used in combination with the dado stack to create rebates (grooves) at the edges of boards. Trying to make a rebate at the edge of a board without a sacrificial fence in place will result in damage to the rip fence.

The sacrificial fence is placed on top of the standard table saw rip fence and secured with the screws on the back side. Ensure that the fence is square to the table while tightening the set screws, and that the fence is flush with the front of the rip fence. Then, slide the fence over top of the dado stack, adjusting the fence for the desired rebate width. Adjust the blade height for the desired depth of rebate.

See: https://www.youtube.com/watch?v=JYqvwlbm6B0 beginning at minute 8 for a demonstration of how the sacrificial fence works.

== Blade Brake ==

This saw is equipped with a safety feature that will (hopefully) stop the blade when it contacts something conductive-- like your hand. However, that means you normally can't cut conductive things with this saw or you will trigger the safety brake. This is good if it was your hand in the way, but it also destroys the sawblade and requires installation of a replacement part that costs $70+ every time. And the saw will be down until the replacement can be installed.

According to the owner's manual: "Conductive materials such as aluminum and other metals, carbon fiber materials, '''mirrored acrylic''', carbon-filled materials, etc. will typically '''cause the brake to activate'''." [Emphasis added.]

Other things that may trigger the brake include wet wood, and wood with embedded nails or staples. Lexan and green pressure-treated wood reportedly can also be a problem. That is why the rules instruct you to check your material on the side of the blade before spinning it up, and to check your wood for nails or staples!

== Notes ==
* There's an m8 hole drilled and tapped in the mitre gauge. The post from a magnetic base of our dial indicators thread in. The post may require a spacer so the threads don't stick out (use a stack of washers or a larger-than-m8 nut).
* The right hand table adjusting screw was bent while aligning the table. The table was aligned without it. Aligning the arbor tilt axis will be *really tough* without a replacement. (Part #11 in the cabinet and table exploded diagram in the manual p98)
* The rear rip fence rail has places to put 4 countersunk allen bolts. The left hand bolt screwed into the main table was too long and made contact with an internal table part (probably the rear trunion). It probably pushed the table out of alignment and caused binding while re-aligning the table. That bolt was left out. Don't replace it!

== Training Links ==
* [http://www.sawstop.com/images/uploads/manuals/PCS%20Owners%20Manual%20Model%20PCS31230%20V5.0%2009-13.pdf Owner's Manual]

== Use checklist ==

PS1 is experimenting with the use of checklists to encourage the safe use and proper care of tools in the workspace. The latest version of the [[checklists]] for this tool is stored as a [https://docs.google.com/document/d/1zxrvQX0DXaLxaXkaKCKpZ-PAgnDak6ezKKBkdu_Fw1U/edit?usp=sharing Google Doc] that can be edited by anyone. If you make changes, update the effective date at the bottom of the document. Print a new copy, and replace the old one.

== Maintenance ==
* [http://web.archive.org/web/20130224091815/http://www.woodworkersjournal.com/Main/Articles/Table_Saw_Maintenance_Skill_Builder_Power_Tool_Tun_8197.aspx Table Saw Maintenance]
* [[SawStop Table Saw maintenance|maintenance page]]

== List of Currently Authorized Users ==
{|Class="wikitable sortable" border="1" style="td { border: 1px solid #000000}"
|-
! Member !! Authorizer !! Date
|-
|-
|Dan Meyer || Sean Blaszak || prior to 2015
|-
|Eric Stein || Steve Finkelman / Danger Committee || prior to 2015
|-
|Dee Newcum || Shawn Blaszak || prior to 2015
|-
|Steve Farkas || Adrianna McKinley || prior to 2015
|-
|Mike Warot || Adrianna McKinley || prior to 2015
|-
|Ryan Pierce || Adrianna McKinley || prior to 2015
|-
|Sean Nixon || Tim Saylor || prior to 2015
|-
|Michael Reddy || Tim Saylor || prior to 2015
|-
|Derek Bever || Tim Saylor || prior to 2015
|-
|Dan Willmott || Tim Saylor || prior to 2015
|-
|Michael Skilton || Adrianna McKinley || prior to 2015
|-
|João Santos || Geoffrey Topham || prior to 2015
|-
|David Fell || Tucker Tomlinson || prior to 2015
|-
|Dan Locks || Adrianna McKinley || prior to 2015
|-
|Dave Earley || Dan Locks || prior to 2015
|-
|Lyn Cole || Tim Saylor || prior to 2015
|-
|George Shaw || Tim Saylor || prior to 2015
|-
|Hilary Lee || Matt Triano || prior to 2015
|-
|Daylan Dufelmeier || Matt Triano || prior to 2015
|-
|Bryan Gleason || Matt Triano || prior to 2015
|-
|Daniel Wells || Matt Triano || prior to 2015
|-
|Aaron Feigen || Matt Triano || prior to 2015
|-
|Lawrence MacDevitt || Matt Triano || prior to 2015
|-
|Ryan Kelly || Matt Triano || prior to 2015
|-
|Ron Bean || Matt Triano || prior to 2015
|-
|Jonathan Bisson || Matt Triano || prior to 2015
|-
|Anna Yu || Matt Triano || prior to 2015
|-
|Bandit Gangwere || Matt Triano || prior to 2015
|-
|David Butler || Matt Triano || prior to 2015
|-
|Ian McLeod || Derek Bever || prior to 2015
|-
|Jeremy Fay || Matt Triano || prior to 2015
|-
|Justin Conroy || Matt Triano || prior to 2015
|-
|Sevin Straus || Matt Triano || prior to 2015
|-
|Ray Doeksen || Jason Shanfield || prior to 2015
|-
|Touly Phiachantharath || Matt Triano || prior to 2015
|-
|Will Garza || Matt Triano || prior to 2015
|-
|Brennan Koziarz || Matt Triano || prior to 2015
|-
|Eric Beauchamp || Matt Triano || prior to 2015
|-
|Josh Myers || Matt Triano || prior to 2015
|-
|Elizabeth Koprucki || Matt Triano || prior to 2015
|-
|Alex Schaffer || Matt Triano || prior to 2015
|-
|Szymon Sambor || Matt Triano || prior to 2015
|-
|Lucas Goossen || Matt Triano || prior to 2015
|-
|John Keippel || Ron Olson || prior to 2015
|-
|Pete Noverini || Matt Triano || prior to 2015
|-
|Dan Baltudis || Ron Olson || prior to 2015
|-
|Ben Bogler || Matt Triano || prior to 2015
|-
|Sam Paris || Matt Triano || prior to 2015
|-
|Bob McGrath || Ron Olson || prior to 2015
|-
|Michelle Deleon || Ron Olson || prior to 2015
|-
|Jennie P || Ron Olson || prior to 2015
|-
|Eugene Liokumovich || Ron Olson || prior to 2015
|-
|John Beyer || Matt Triano || prior to 2015
|-
|Erik Wessing || Eric Beauchamp || prior to 2015
|-
|Marcin Ignasiak || Eric Beauchamp || prior to 2015
|-
|Abel Greenwald || Andy Larkin || prior to 2015
|-
|Glenn Powers || Matt Triano || Mar/01/2015
|-
|Mike Jones || Matt Triano || May/12/2015
|-
|Mark Stevens || Eric Beauchamp || Jul/18/2015
|-
|Ralph Brendler || Eric Beauchamp || Aug/27/2015
|-
|Shane Kanter || Ron Olson || Sep/10/2015
|-
|Burton Kent || Ron Olson || Sep/10/2015
|-
|Jeff Smykil || Matt Triano || Sep/26/2015
|-
|John McDonald || Eric Beauchamp || Oct/05/2015
|-
|Aaron Carlock || Eric Beauchamp || Nov/19/2015
|-
|Patrick Lynch || Eric Beauchamp || Nov/19/2015
|-
|Alex Al-Hamdan || Eric Beauchamp || Dec/04/2015
|-
|Jared K. || Eric Beauchamp || Mar/10/2016
|-
|Mark Zumwalt || Andy Larkin || Mar/17/2016
|-
|Adam Stein || Andy Larkin || Apr/14/2016
|-
|Greg "Nerobro" Teiber || Dan Locks || Apr/29/2016
|-
|Spencer Simms || Eric Beauchamp || May/19/2016
|-
|Jim Brink || Andy Larkin || Jul/21/2016
|-
|Derwin Umali || Andy Larkin || Aug/04/2016
|-
|Joe Dowling || Ken Burkhardt || Aug/15/2016
|-
|Revant Ohri || Andy L || Sep/15/2016
|-
|Max Rashes || Ken Burkhardt || Sep/20/2016
|-
|Jon Komperda || Ken Burkhardt || Oct/17/2016
|-
|Logan Price || Andy Larkin || Nov/21/2016
|-
|Tony Iacullo || Andy || Dec/05/2016
|-
|John McBride || Andy Larkin || Jan/19/2017
|-
|Bruce Mace || Eric Beauchamp || Feb/20/2017
|-
|Matthew Quigley || Andy Larkin || Mar/02/2017
|-
|Molly Adamski || Ralph Brendler || Apr/27/2017
|-
|David Earl || Ralph Brendler || May/04/2017
|-
|Jim Handley || Ralph Brendler || May/13/2017
|-
|Paul McClay || Ralph Brendler || May/18/2017
|-
|Kari Danek || Ralph Brendler || Jun/15/2017
|-
|Danielle MacDonald || Ralph Brendler || Jun/29/2017
|-
|Andrew Wingate || Jason Shanfield || Jul/22/2017
|-
|Zack Sasnow || Paul Van Lake || Aug/03/2017
|-
|Christophe Laurent || Ralph Brendler || Aug/10/2017
|-
|Jacob Snyder || Ralph Brendler || Sep/07/2017
|-
|Mark Haughey || Sevin Straus || Sep/30/2017
|-
|Theo T || Ralph Brendler || Nov/30/2017
|-
|Wally Ibrahim || Ralph Brendler || Nov/30/2017
|-
|Sam Holtman || Paul V || Dec/06/2017
|-
|Ben Starett || Ralph Brendler || Dec/14/2017
|-
|Ross Hanchett || Ralph Brendler || Dec/14/2017
|-
|Michael Donovan || Ralph Brendler || Dec/14/2017
|-
|Jamin Nollsch || Ralph Brendler || Dec/28/2017
|-
|Aaron Vander Bee || Ralph Brandler || Jan/11/2018
|-
|Ben Farmer || Ralph Brendler || Jan/11/2018
|-
|Joseph Crouch || Ralph Brendler || Jan/11/2018
|-
|Bradford Smith || Ralph Brendler || Jan/11/2018
|-
|Stephanie Pelzer || Ralph Brendler || Jan/11/2018
|-
|Amanda Assaley || Ralph Brendler || Jan/11/2018
|-
|Chris Eppig || Ralph Brendler || Jan/11/2018
|-
|Patrick Smith || Ralph Brendler || Jan/11/2018
|-
|Jeff Gershune || Paul VanLake || Jan/16/2018
|-
|Bryan Pennington || Ralph Brendler || Jan/25/2018
|-
|Michael Ice || Ralph Brendler || Feb/08/2018
|-
|Francisco Becerril || Ralph Brendler || Feb/08/2018
|-
|Brandon Kennedy || Ralph Brendler || Feb/22/2018
|-
|Rolf Scheidt || Ralph Brendler || Feb/22/2018
|-
|Charles Barker || Ralph Brendler || Mar/08/2018
|-
|Dan Mach || Ralph Brendler || Mar/08/2018
|-
|Bruce Mace || Ralph Brendler || Mar/08/2018
|-
|Nick Prorok || Ralph Brendler || Mar/08/2018
|-
|Ricardo Staudt || Ralph Brendler || Mar/08/2018
|-
|Paul Graham || Ralph Brendler || Mar/22/2018
|-
|Mike Gucciard || Ralph Brendler || Mar/22/2018
|-
|Wayne Warren || Ralph Brendler || Mar/22/2018
|-
|Adam Hall || Paul V || Mar/29/2018
|-
|Bill Schroeder || Ralph Brendler || Apr/05/2018
|-
|Mike Wilkin || Ralph Brendler || Apr/19/2018
|-
|Alex Lanigan || Ralph Brendler || Apr/19/2018
|-
|Jessica Jokhi || Ralph Brendler || Apr/19/2018
|-
|Matt Maggio || Ralph Brendler || Apr/19/2018
|-
|Jonathan Frink || Ralph Brendler || Apr/19/2018
|-
|Ian Brieger || Ralph Brendler || Apr/19/2018
|-
|Wayne Hendryx || Ralph Brendler || Apr/19/2018
|-
|Gary Newhouse || Ralph Brendler || Apr/26/2018
|-
|Dave DesRoberts || Paul Van Lake || Apr/26/2018
|-
|Jennifer DesRoberts || Paul Van Lake || Apr/26/2018
|-
|John Burkholder || Ralph Brendler || May/03/2018
|-
|Brendan Fortune || Ralph Brendler || May/17/2018
|-
|Fritz Sullivan || Ralph Brendler || May/30/2018
|-
|Elizabeth Reuter || Ralph Brendler || May/30/2018
|-
|Kirsten Landmark Masih || Ralph Brendler || Jun/07/2018
|-
|Chris Niziolek || Ralph Brendler || Jun/14/2018
|-
|Bob Fritz || Ralph Brendler || Jun/14/2018
|-
|Sam Wallinga || Ralph Brendler || Jun/14/2018
|-
|Nate Myren || Ralph Brendler || Jun/14/2018
|-
|Eli Schlossberg || Ralph Brendler || Jun/14/2018
|-
|Tyler Works || Ralph Brendler || Jun/14/2018
|-
|Bruce Levin || Paul V || Jul/05/2018
|-
|Joe Day || Paul V || Jul/05/2018
|-
|Mike Yacobucci || Ralph Brendler || Jul/12/2018
|-
|Mike Yacobucci || Ralph Brendler || Jul/12/2018
|-
|Aaron Hale || Ralph Brendler || Jul/26/2018
|-
|Adam Wilk || Ralph Brendler || Jul/26/2018
|-
|Adam Wilk || Ralph Brendler || Jul/26/2018
|-
|Adam Wilk || Ralph Brendler || Jul/26/2018
|-
|Aaron Hale || Ralph Brendler || Jul/26/2018
|-
|Geoff Klein || Paul V || Sep/13/2018
|-
|Earl Wood || Paul V || Sep/13/2018
|-
|Jacob Dawson || Paul V || Sep/13/2018
|-
|Jacob Dawson || Paul V || Sep/13/2018
|-
|Geoff Klein || Paul V || Sep/13/2018
|-
|Geoff Klein || Paul V || Sep/13/2018
|-
|Earl Wood || Paul V || Sep/13/2018
|-
|Earl Wood || Paul V || Sep/13/2018
|-
|Jacob Dawson || Paul V || Sep/13/2018
|-
|Farsheed Hamidi-Toosi || Paul V || Sep/27/2018
|-
|Farsheed Hamidi-Toosi || Paul V || Sep/27/2018
|-
|Tim Bielawa || Paul V || Sep/27/2018
|-
|Farsheed Hamidi-Toosi || Paul V || Sep/27/2018
|-
|Gwenn-Ael Lynn || Ralph Brendler || Oct/04/2018
|-
|Gwenn-Ael Lynn || Ralph Brendler || Oct/04/2018
|-
|Tatjana Paunesku || Ralph Brendler || Nov/29/2018
|-
|Kevin Bradley || Paul V || Dec/07/2018
|-
|Dan Gulick || Paul V || Dec/07/2018
|-
|Jim Lund || Paul Van Lake || Dec/07/2018
|-
|Deanna Musurlian || Ralph Brendler || Jan/24/2019
|-
|Pat Hillegass || Ralph Brendler || Jan/24/2019
|-
|Brian Barnt || Ralph Brendler || Feb/07/2019
|-
|Matt Dinning || Ralph Brendler || Feb/07/2019
|-
|Tony Green || Ralph Brendler || Feb/07/2019
|-
|Johanna Vargas || David Earl || Feb/13/2019
|-
|Alex Biardo || Paul Van Lake || Mar/01/2019
|-
|Tyler Moench || Ralph Brendler || Mar/03/2019
|-
|Carsten Lohan || Ralph Brendler || Mar/07/2019
|-
|Bobby Salazar || Ralph Brendler || Mar/21/2019
|-
|Vaibhav Konanur || Paul Van Lake || Mar/30/2019
|-
|Sean Blum || Ralph Brendler || Apr/04/2019
|-
|Maciej Warchalowski || Paul V || Apr/10/2019
|-
|David Earley || Ralph Brendler || Apr/18/2019
|-
|Zach Graceffa || Ralph Brendler || Apr/18/2019
|-
|David Pfeffer || Paul V || May/24/2019
|-
|Jack Gibbons || Paul V || Jun/20/2019
|-
|Tim Whelan || Ralph Brendler || Jun/27/2019
|-
|Andrew Soghigian || Ralph Brendler || Jul/11/2019
|-
|Luke Krudwig || Ralph Brendler || Jul/11/2019
|-
|Nathan Upchurch || Ralph Brendler || Jul/11/2019
|-
|Paul Ocampo || Ralph Brendler || Jul/11/2019
|-
|Eric Kostecki || Paul V || Jul/18/2019
|-
|Michael Baker || Paul V || Jul/18/2019
|-
|Sarah Lu || Ralph Brendler || Jul/25/2019
|-
|Connar Rosebraugh || Ralph Brendler || Aug/01/2019
|-
|Joseph Kardia || Ralph Brendler || Aug/01/2019
|-
|Kevin Huemann || Ralph Brendler || Aug/01/2019
|-
|Szymon Mirek || David Earl || Aug/18/2019
|-
|Justin Pestka || Ralph Brendler || Aug/30/2019
|-
|Arjun Sharma || Ralph Brendler || aug 10 2017
|-
|Mike Thompson || Michelle DeLeon || 08/22/19
|-
|Denise Allen || Paul V || 08/29/19
|-
|Sam Vuchetich || Ralph Brendler || 09/05/19
|-
|Malindima Sampa || Paul V || 10/11/19
|-
|Nikolas Gamarra || Ralph Brendler || 10/13/19
|-
|Tony Vetter || Michelle DeLeon || 10/06/19
|-
|Drew Deitch || Michelle DeLeon || 10/31/19
|-
|Adam Rangwala || Ralph Brendler || 11/14/19
|-
|Derek Smith || Ralph Brendler || 11/14/19
|-
|Jeff Becker || Eric Beauchamp || 11/23/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|Ryan Zoghlin
|Paul V
|1/16/2020
|-
|David Robbins
|Paul V
|1/16/2020
|}

[[Category:Shop Equipment]]
[[Category:Fabrication]]
[[Category:Wood Shop]]

Laguna 16" Planer

2020-01-18T23:12:20Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = no
|model = MPLAN1510-0120
|serial = 144367
|arrived =
|doesitwork = yes
|contact =
|where = Wood Shop
|value = $3000
|image = LagunaPlaner.jpg
|hostarea = Wood Shop
}}
== reference material ==
[[file:Laguna16PlanerManual.pdf]]
== Guidelines for proper use ==
# '''Always''' check your wood for nails or staples. Something as small as the staple at the end of a 1x1 can ruin the blades. If you're not sure, check the entire piece with the metal detector sitting on the table saw.
# '''Always''' measure the thickness of your work and set the initial and working blade height to remove only small amounts of material per pass. You will damage the blades if you manage to dig the machine out on your work.
# If the machine is making a strange noise when you use it, there is a problem, and you should '''ask for help.'''
# If the blades are dull or damaged, '''contact the area host immediately.'''
# If you break something, or damage the tool, '''contact the area host immediately.''' Don't let others do more damage or hurt themselves by using a broken tool.
# '''Always''' make sure that the dust collection bag isn't too full and is passing air freely.
# '''Always''' vacuum the machine, cutting area, and the table around the machine when you are done.

April 29 2019. Planer shut down in mid use. Broken elec connection repaired but sill does not start. See gg and slack for more detail.
'''This tool requires authorization for use.'''

== Checklist ==
PS1 is experimenting with the use of [[checklists]] to encourage the safe use and proper care of tools in the workspace. The latest version of the checklist for this tool is stored as a [https://docs.google.com/document/d/1C0pna59ZDq92vC2uEZM5ANUGh6qx-svit9atMhJNLm8/edit?usp=sharing Google Doc] that can be edited by anyone. If you make changes, update the effective date at the bottom of the document. Print a new copy, and replace the old one.

== External Links ==
*[https://lagunatools.com/classic-machinery/planers/planer-16-inch-4-post/ Manufacturer Page]
*[https://system.na3.netsuite.com/core/media/media.nl?id=661707&c=860860&h=94f90373845230ed877d&_xt=.pdf Owner's Manual]
maintenance gdoc click on "1" to view, "link icon" to edit [https://docs.google.com/spreadsheets/d/e/2PACX-1vRiwd8cogJ6NOWSUqhAaSJM_vcQi1nAUZ-dqsxR4iuGnFKr1g8X5w7qmZNjkeD3xK_f9pwu1Vnu09wm/pubhtml]
* [https://docs.google.com/spreadsheets/d/e/2PACX-1vRiwd8cogJ6NOWSUqhAaSJM_vcQi1nAUZ-dqsxR4iuGnFKr1g8X5w7qmZNjkeD3xK_f9pwu1Vnu09wm/pubhtml Internal PS1 Maintenance Google Doc]

{{WoodshopProctors}}

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Matt Triano
|Danger committee
|
|-
|Eric Beauchamp
|Danger committee
|
|-
|Jason Shanfield
|Matt Triano
|
|-
|Tom Judge
|Matt Triano
|
|-
|Hunter Koerner
|Eric Beauchamp
|
|-
|Deanna Williams
|Eric Beauchamp
|
|-
|Casey Olson
|Eric Beauchamp
|
|-
|Burton Kent
|Eric Beauchamp
|
|-
|Jeff Smykil
|Matt Triano
|
|-
|Ray Doeksen
|Jason Shanfield
|
|-
|Anna Yu
|Jason Shanfield
|
|-
|Todd Allen
|Ron Olson
|
|-
|Jon Levine
|Jason Shanfield
|
|-
|Kyle Bieneman
|Eric Beauchamp
|
|-
|Niko Hawley
|Eric Beauchamp
|
|-
|-
|Adam Moffatt
|Eric Beauchamp
|
|-
|Marcin Ignasiak
|Eric Beauchamp
|
|-
|Keon Turner
|Ron Olson
|
|-
|Mike Mandrea
|Eric Beauchamp
|
|-
|Caleb Young
|Eric Beauchamp
|
|-
|Erik Wessing
|Eric Beauchamp
|
|-
|Doorman Dave
|Eric Beauchamp
|
|-
|Peter Letscher
|Eric Beauchamp
|11/05/15
|-
|Glenn Trussell
|Eric Beauchamp
|11/05/2015
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Shine Chen
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/03/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Chris Kohl
|Eric Beauchamp
|1/8/2016
|-
|Szymon Sambor
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Peter Brask
|Eric Beauchamp
|1/14/16
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
|Shelly Loke-Gayares
|Eric Beauchamp
|1/14/16
|-
|Saul Weiner
|Eric Beauchamp
|1/14/16
|-
|Brandon Love
|Eric Beauchamp
|1/28/16
|-
|Christopher Carson
|Eric Beauchamp
|2/25/16
|-
|Jared K
|Andy L
|3/03/16
|-
|Keith Couture
|Eric Beauchamp
|3/10/16
|-
|Julie Zwolinski
|Eric Beauchamp
|3/24/16
|-
|Nick Puglisi
|Eric Beauchamp
|4/21/16
|-
|Andy Muhic
|Andy Larkin
|4/28/16
|-
|Greg "Nerobro" Teiber
|Dan Locks
|4/29/16
|-
|Ken Burkhardt
|Andy Larkin
|5/5/16
|-
|Hans Griese
|Andy Larkin
|5/5/16
|-
|Spencer Simms
|Eric Beauchamp
|05/19/2016
|-
|Josh Younger
|Eric Beauchamp
|5/19/16
|-
|Ian Monroe
|Eric Beauchamp
|5/19/16
|-
|Joseph Juhnke
|Eric Beauchamp
|6/20/16
|-
|An Phan
|Andy Larkin
|07/07/16
|-
|Jim Brink
|Andy Larkin
|07/21/16
|-
|Donald Wells
|Andy Larkin
|8/4/16
|-
|Derwin Umali
|Andy Larkin
|8/7/16
|-
|[[User:mct|McTavish McArdle]]
|Andy Larkin
|2016-08-04
|-
|Joe Dowling
|Ken Burkhardt
|8/15/16
|-
|Leo Rodman
|Jason S
|9/12/16
|-
|Brian Cuocci
|Andy L
|9/15/16
|-
|Revant Ohri
|Andy L
|9/15/16
|-
|Max Rashes
|Ken Burkhardt
|9/20/16
|-
|Aaron Mintz
|Ken Burkhardt
|10/17/16
|-
|Brian Carstensen
|Ken Burkhardt
|10/17/16
|-
|Jon Komperda
|Ken Burkhardt
|10/17/16
|-
|Regan Via
|Ken Burkhardt
|10/17/16
|-
|Robert Richardson
|Ken Burkhardt
|10/17/16
|-
|Jack Berg
|Ken Burkhardt
|11/07/16
|-
|Logan Price
|Andy Larkin
|11/21/16
|-
|Kris Blouch
|Andy Larkin
|11/21/16
|-
|Tony Iacullo
|Andy
|12/5/16
|-
|Ashish Jasani
|Andy Larkin
|11/28/16
|-
|Chris Ruhland
|Andy Larkin
|01/05/17
|-
|John McBride
|Andy Larkin
|01/19/17
|-
|Will Heil
|Andy Larkin
|01/19/17
|-
|Dusty Buyck
|Andy Larkin
|01/19/17
|-
|Matthew Quigley
|Andy Larkin
|03/02/17
|-
|W. Anthony Claypool
|Andy Larkin
|03/16/17
|-
|-
|Crystal Morales
|Andy Larkin
|2017-03-16
|-
|Jason Pittman
|Andy Larkin
|2017-03-16
|-
|Ashley Borg
|Andy Larkin
|4/13/17
|-
|Sam Chen
|Andy Larkin
|
|-
| [[User:Andrewvaughan|Andrew Vaughan]]
| Andy Larkin
| 2017-04-25
|-
|Molly Adamski
|Ralph Brendler
|4/27/17
|-
|Shabab Mustafa
|Ralph Brendler
|4/27/17
|-
|Adomas Tautkus
|Ralph Brendler
|4/27/17
|-
|Crystal Zapata
|Ralph Brendler
|4/27/17
|-
|Alexa Viscius
|Ralph Brendler
|4/27/17
|-
|David Earl
|Ralph Brendler
|5/4/17
|-
|Luis Colmenares
|Ralph Brendler
|6/1/17
|-
|Kari Danek
|Ralph Brendler
|6/15/17
|-
|Christophe Laurent
|Ralph Brendler
|8/10/17
|-
|[[User:spektre1|Danielle MacDonald]]
|Ralph Brendler
|2017-06-29
|-
|Zack Sasnow
|Paul Van Lake
|8/3/17
|-
|Arjun Sharma
|Ralph Brendler
|8.10.17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|Sam Dreyer
|Ralph Brendler
|8/30/17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|Mark Haughey
|Sevin Straus
|9/30/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
| Tommy TBones Cramer
|Ralph Brendlet
|08/30/17
|-
|Mike Thariath
|Ralph Brendlet
|10/19/17
|-
|Chinbayar Davaatseren
|Ralph Brendler
|11/02/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Tee
|Paul V
|11/09/17
|--
|[[User:frenchy|Jeremie Davis]]
|Ralph Brendler
|11/16/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Jeff Hassberger
|Ralph Brendler
|11/2/17
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Mac MacDevitt
|Paul V
|12/7/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Jamin Nollsch
|Ralph Brendler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brandler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Scott Fullman
|Ralph Brendler
|2/8/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Nick Prorok
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|[[User:waynr|Wayne Warren]]
|Ralph Brendler
|3/22/18
|-
|Adam Hall
|Paul V
|3/29/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Matt Maggio
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|4/19/18
|-}
|Gary Newhouse
|Ralph Brendler
|4/26/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
|John Burkholder
|Ralph Brendler
|5/03/18
|-
| Wayne Hendryx
| Ralph Brendler
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Eli Schlossberg
| Ralph Brendler
| 6/14/18
|-
| Tyler Works
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Bruce Levin
| Paul V
| 7/05/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Kathryn Connolly
| Paul V
| 7/19/18
|-
| Sam Lewis
| Paul V
| 7/19/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Adam Wilk
| Ralph Brendler
| 7/26/18
|-
|Tom Henderson
|Ralph Brendler
|2018-08-09
|-
| Kelvin Lane
| Paul V
| 9/13/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Earl Wood
| Paul V
| 9/13/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
| Will Brown
| Ralph Brendler
| 10/31/18
|-
| Tatjana Paunesku (tpaune)
| Ralph Brendler
| 11/29/18
|-
|Jim Lund
|Paul Van Lake
|12/6/18
|-
|Pat Hillegass
|Ralph Brendler
|1/24/19
|-
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
|Tony Green
|Ralph Brendler
|02/07/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|David Pfeffer
|Paul V
|05/24/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Nathan Upchurch
|Ralph Brendler
|07/11/19
|-
|Andrew Soghigian
|Ralph Brendler
|07/11/19
|-
|Luke Krudwig
|Ralph Brendler
|07/11/19
|-
|Paul Ocampo
|Ralph Brendler
|07/11/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Sarah Lu
|Ralph Brendler
|07/25/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Connar Rosebraugh
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Hara Kumaran
|David Earl
|08/18/19
|-
|Steven Rummelhoff
|Ralph Brendler
|08/22/19
|-
|-
|Mike Thompson
|Michelle DeLeon
|08/22/19
|-
|Denise Allen
|Paul V
|08/29/19
|-
|Sam Vuchetich
|Ralph Brendler
|09/05/19
|-
|Nikolas Gamarra
|Ralph Brendler
|10/13/19
|-
|Adam Rangwala
|Ralph Brendler
|11/14/19
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|Ryan Zoghlin
|Paul V
|1/16/2020
|-
|David Robbins
|Paul V
|1/16/2020
|}
[[Category:Wood Shop]]
[[Category:Shop Equipment]]

Rockwell Delta 20" Bandsaw

2020-01-18T23:11:34Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = Pumping Station:One
|hostarea = Wood Shop
|certification = yes
|hackable = no
|model = 28-350
|serial = 1457257
|arrived = 8/26/15
|where = Wood Shop
|doesitwork = yes
|contact = matt . triano @ gmail . com
|trustee = Ralph Brendler
|value = $1,000
|move me = yes
|image = RockwellDelta20Bandsaw.jpg
}}

=== Status ===
* 3/6/2019. Andrew w replaced drive belt
* 2/23/2019 drive belt broke, status will be updated once underway/fixed.
* 10/18/2018 blade broke & Eric B. replaced it
* 5/31/2019 someone broke off one of the guides while “brushing off” the table. it is usable but blade stability is poor. NEW guide made by helpful cold metals.
*. 8/2019. Drive belt and pulley came off drive shaft. Eric and Gary replaced but drive belt does not run perfectly true. Brake does not seem to be optimally functional. Ralph will do a tune up soon.

* Tires are out of lateral alignment as well. Ralph and helpers will do a total overhaul Saturday 9/7/2019
* 9/8/2019. Ralph and Tim did total overhaul with new tires and belt. But later in day, blade was reportedly running off lower tire.

* Ralph repaired lower tire. Discovered that we cannot run at fastest pulley setting.
* 9/10 throat plate broken again
* 9/16/19 joe made new throat plate
* 10/13/19. Ralph discovered major bearing issues. Parts ordered.
* 11/2/2019. Ralph put it back into service with the great assistance of Jim brink
* 12/29/2019 thrust bearings and guides failure
* 12/31/2019 Ralph replaced thrust bearings, guides and other pats top wheel bearing/shaft still needs work, but she's usable again

* 1/8/2020 blade badly kinked. person was sawing fresh bark-on logs. i spoke with him AFTER. gn
switched to fine blade. new 1/2 inch blade on wall hanger

==Notes==
manual: [[File:Rockwell-28-350.pdf]]
related manual with more details: [[File:Rockwell20bandsaw.pdf]]

* https://ozarktoolmanuals.com/ozarkshoptalkblog/machine-idd-rockwell-delta-20-wood-band-saw-28-350/

The best manual is at http://www.walkemooretools.com/wp/wp-content/uploads/2015/07/Delta_Rockwell-bandsaw-manual.pdf

== Authorization; How to get Authorized ==

*Authorizations for the 14" Rockwell do not carry over to this tool
*This tool requires authorization for use.
*To be authorized, please see an authorized proctor/trainer from the list, below.

=== Consumable Parts ===
* This saw takes 141" blades.
* Thrust bearings type [https://www.mcmaster.com/5972k2 6203-2Z] (17mm x 40mm x 12mm). Be sure to get 2Z or ZZ (steel shield) and not 2RS (rubber shield).
* Throat plate. We still need this made frequently

Throat plate templates/model courtesy of Joe Dowling

zip of SKP, STL and f3D files : [[File:Bandsaw Plate.zip]]

image [[Media:picofbandsawplate.jpg]] and

Fusion 360 model at Joe's Adobe360 https://a360.co/2RdzuCe

There is usually a spare plates in the locked cabinet

==Tips on Use==

This section is based on a [https://groups.google.com/forum/#!msg/pumping-station-one/rCix6WMMS4Q/S6Ds9sO7DAAJ discussion that took place on the mailing list].

Band-saws have two main uses in the wood shop:

# The primary use is to make curved cuts in a piece of flat wood. In this case the piece is held by hand and guided so the blade follows the curve. A fence is counterproductive for this use.
# The second is resawing lumber that is too thick for the table saw. This is typically, but not exclusively, done with valuable pieces of wood for the purpose of creating a veneer. A fence may be appropriate for this use.

With a bandsaw, you basically never want to have the fence locked parallel to the blade. Every blade will have some degree of drift, and it is necessary to accommodate this drift to achieve a straight cut. There are two common solutions: single-point fences, and adjustable angle fences. PS:1 has both a nice magnetic adjustable fence and a single-point fence that attaches to it.

With a single point fence, you adjust for the drift angle by eye as you cut. This quick and easy method is most appropriate for resawing of narrower boards with a width of 6" or less.

For wider boards, use the adjustable fence with a tall secondary fence attached, carefully adjusted to the drift angle of the blade. For really wide boards, you can also use a presser-board to ensure contact with the fence.

Some additional advice on resawing:

* Buy a nice blade and learn how to install and adjust it. The PS:1 blades are often fairly dull and don't track well.
* Make sure your stock is prepared well, with at least one flat face and one square and flat edge.
* Try to keep only 3-10 teeth in the wood. A 1.5 tpi blade is appropriate for most resawing.
* Use a skip-tooth blade, at least 1" wide (but see note below).

{{WoodshopProctors}}

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Keon Turner
|Ron Olson
|
|-
|Hunter Koerner
|Eric Beauchamp
|
|-
|Deanna Williams
|Eric Beauchamp
|
|-
|Ray Doeksen
|Eric Beauchamp
|
|-
|Burton Kent
|Eric Beauchamp
|
|-
|Casey Olson
|Jason Shanfield
|
|-
|Tom Judge
|Matt Triano
|
|-
|Jeff Smykil
|(Pending confirmation)
|
|-
|Anna Yu
|Matt Triano
|
|-
|Jon Levine
|Jason Shanfield
|
|-
|Kyle Bieneman
|Eric Beauchamp
|
|-
|Niko Hawley
|Eric Beauchamp
|
|-
|Kevin Mitchell
|Eric Beauchamp
|
|-
|Adam Moffatt
|Jason Shanfield
|
|-
|Peter Letscher
|Eric Beauchamp
|11/05/15
|-
|Glenn Trussell
|Eric Beauchamp
|11/05/2015
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Shine Chen
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/04/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Marcin Ignasiak
|Eric Beauchamp
|
|-
|Thomas Ward
|Andy L.
|11/18/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Chris Kohl
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Peter Brask
|Eric Beauchamp
|1/14/16
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
|Shelly Loke-Gayares
|Eric Beauchamp
|1/14/16
|-
|Saul Weiner
|Eric Beauchamp
|1/14/16
|-
|Brandon Love
|Eric Beauchamp
|1/28/16
|-
|Sam Paris
|Eric Beauchamp
|1/28/16
|-
|Craig Koszewski
|Eric Beauchamp
|1/28/16
|-
|Christopher Carson
|Eric Beauchamp
|2/25/16
|-
|Jared K
|Andy L
|3/03/16
|-
|Keith Couture
|Eric Beauchamp
|3/10/16
|-
|Brian Cuocci
|Andy L
|3/17/16
|-
|Julie Zwolinski
|Eric Beauchamp
|3/24/16
|-
|Nick Puglisi
|Eric Beauchamp
|4/21/16
|-
|Andy Muhic
|Andy Larkin
|4/28/16
|-
|Colin Campbell
|Andy L
|5/5/16
|-
|Ken Burkhardt
|Andy Larkin
|5/5/16
|-
|Hans Griese
|Andy Larkin
|5/5/16
|-
|Josh Younger
|Eric Beauchamp
|5/19/16
|-
|Ian Monroe
|Eric Beauchamp
|5/19/16
|-
|An Phan
|Andy Larkin
|7/7/16
|-
|Donald Wells
|Andy Larkin
|8/4/16
|-
|Derwin Umali
|Andy Larkin
|8/7/16
|-
|[[User:mct|McTavish McArdle]]
|Andy Larkin
|2016-08-04
|-
|Joe Dowling
|Ken Burkhardt
|8/15/16
|-
|Leo Rodman
|Jason S
|9/12/16
|-
|[[user:guijemont|Guillaume Emont]]
|Ken Burkhardt
|9/19/16
|-
|Max Rashes
|Ken Burkhardt
|9/20/16
|-
|Revant Ohri
|Andy L
|9/15/16
|-
|Aaron Mintz
|Ken Burkhardt
|10/17/16
|-
|Brian Carstensen
|Ken Burkhardt
|10/17/16
|-
|Jon Komperda
|Ken Burkhardt
|10/17/16
|-
|Regan Via
|Ken Burkhardt
|10/17/16
|-
|Robert Richardson
|Ken Burkhardt
|10/17/16
|-
|Ryan Fiebing
|Ken Burkhardt
|10/24/16
|-
|Jack Berg
|Ken Burkhardt
|11/07/16
|-
|Logan Price
|Andy Larkin
|11/21/16
|-
|Kris Blouch
|Andy Larkin
|11/21/16
|-
|Tony Iacullo
|Andy
|12/5/16
|-
|Chris Ruhland
|Andy Larkin
|01/05/17
|-
|John McBride
|Andy Larkin
|01/19/17
|-
|Will Heil
|Andy Larkin
|01/19/17
|-
|Dusty Buyck
|Andy Larkin
|01/19/17
|-
|Bruce Mace
|Eric Beauchamp
|02/20/17
|-
|Matthew Quigley
|Andy Larkin
|03/02/17
|-
|W. Anthony Claypool
|Andy Larkin
|03/16/17
|-
|Crystal Morales
|Andy Larkin
|2017-03-16
|-
|Jason Pittman
|Andy Larkin
|2017-03-16
|-
|Sam Chen
|Andy Larkin
|
|-
|Abel Greenwald
|Andy Larkin
|
|-
| [[User:Andrewvaughan|Andrew Vaughan]]
| Andy Larkin
| 2017-04-25
|-
|Molly Adamski
|Ralph Brendler
|4/27/17
|-
|Shabab Mustafa
|Ralph Brendler
|4/27/17
|-
|Adomas Tautkus
|Ralph Brendler
|4/27/17
|-
|Crystal Zapata
|Ralph Brendler
|4/27/17
|-
|Alexa Viscius
|Ralph Brendler
|4/27/17
|-
|David Earl
|Ralph Brendler
|5/4/17
|-
|Paul McClay
|Ralph Brendler
|5/18/17
|-
|Jim Handley
|Ralph Brendler
|5/13/17
|-
|Luis Colmenares
|Ralph Brendler
|6/1/17
|-
|Kari Danek
|Ralph Brendler
|6/15/17
|-
|Christophe Laurent
|Ralph Brendler
|8/10/17
|-
|[[User:spektre1|Danielle MacDonald]]
|Ralph Brendler
|2017-06-29
|-
|Zack Sasnow
|Paul Van Lake
|8/3/2017
|-
|Arjun Sharma
|Ralph Brendler
|8.10.17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|Sam Dreyer
|Ralph Brendler
|8/30/17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|Joanna C.
|Sam O.
|9/27/17
|-
|Mark Haughey
|Sevin Straus
|9/30/17
|-
|Jacqueline Villa
|Maria Miller
|10/3/17
|-
|Mike Thariath
|Ralph Brendler
|10/19/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Tee
|Paul V
|11/09/17
|-
|Nick Fera
|Paul V
|11/09/17
|-
|[[User:frenchy|Jeremie Davis]]
|Ralph Brendler
|11/16/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Corey Toyama
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Jeff Hassberger
|Ralph Brendler
|
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Mac MacDevitt
|Paul V
|12/7/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Jamin Nollsch
|Ralph Brendler
|12/28/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brandler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Michael Ice
|Ralph Brendler
|2/08/18
|-
|Francisco becerril
|Ralph Brendler
|2/08/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|[[User:waynr|Wayne Warren]]
|Ralph Brendler
|3/22/18
|-
|Adam Hall
|Paul V
|3/29/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Matt Maggio
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|4/19/18
|-}
|Gary Newhouse
|Ralph Brendler
|4/19/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
| Wayne Hendryx
| Ralph Brendler
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Fritz Sullivan
| Ralph Brendler
| 5/30/18
|-
| Elizabeth Reuter
| Ralph Brendler
| 5/30/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Chris Niziolek
| Ralph Brendler
| 6/14/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Eli Schlossberg
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Bruce Levin
| Paul V
| 7/05/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Kathryn Connolly
| Paul V
| 7/19/18
|-
| Sam Lewis
| Paul V
| 7/19/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Adam Wilk
| Ralph Brendler
| 7/26/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Earl Wood
| Paul V
| 9/13/18
|-
| Jacob Dawson
| Paul V
| 9/13/18
|-
|Nick Prorok
|Ralph Brendler
|3/8/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Tim Bielawa
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
| Landon Smith
| Ralph Brendler
| 10/18/18
|-
| Will Brown
| Ralph Brendler
| 10/31/18
|-
| Tatjana Paunesku (tpaune)
| Ralph Brendler
| 11/29/18
|-
|Jim Lund
|Paul Van Lake
|12/7/18
|-
|Deanna Musurlian
|Ralph Brendler
|01/24/19
|-
|Pat Hillegass
|Ralph Brendler
|1/24/19
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Charlie Kepner
|Paul Van Lake
|03/01/19
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
|Tony Green
|Ralph Brendler
|02/07/19
|-
|Craig Cernek
|Dave Solomon
|03/27/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|Zach Graceffa
| Ralph Brendler
|4/18/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|David Pfeffer
|Paul V
|05/24/19
|-
|Jack Gibbons
|Paul V
|06/20/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Patrick Cook
|Ralph Brendler
|07/11/19
|-
|Matt Saunders
|Ralph Brendler
|07/11/19
|-
|Nathan Upchurch
|Ralph Brendler
|07/11/19
|-
|Luke Krudwig
|Ralph Brendler
|07/11/19
|-
|Andrew Soghigian
|Ralph Brendler
|07/11/19
|-
|Eric Kostecki
|Paul V
|07/18/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Sarah Lu
|Ralph Brendler
|07/25/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Connar Rosebraugh
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Hara Kumaran
|David Earl
|08/18/19
|-
|Miles Hosanna
|Ralph Brendler
|09/19/2019
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|Tony Vetter
|Michelle DeLeon
|10/06/19
|-
|Adam Rangwala
|Ralph Brendler
|11/14/19
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Adam Keim
|Ralph Brendler
|11/14/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|Ryan Zoghlin
|Paul V
|1/16/2020
|-
|David Robbins
|Paul V
|1/16/2020
|}

[[Category:Wood Shop]]
[[Category:Shop Equipment]]

Ridgid Oscillating Spindle Sander

2020-01-18T23:11:04Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|certification=yes
|hackable = NO
|model = G0654
|serial = NA
|arrived = December 2014
|doesitwork = yes
|contact = Matt Triano
|where = Wood Shop
|hostarea = Wood Shop
|value = $200.00
|image = ridgidossander.jpg
}}

please see: https://wiki.pumpingstationone.org/Sander_(oscillating_spindle)_-_Steel_City
it is the current spindle sander since mid 2018. However it no longer oscillates so this backup returns to service.

'''This tool requires authorization for use.

12/26/2019 replaced spindle knob . THIS IS A LEFT HAND THREADED KNOB AND SEEMS TO CONFUSE MANY USERS '''

The belt sander attachment lives in a pocket at the back of the tool.

{{WoodshopProctors}}

== Rules ==
# Always check your wood for nails or staples. If you're not sure, check the entire piece with the metal detector or a magnet.
# Always use dust collection.
# Always use the appropriate washer with the oscillating drums, and put the washers away when you're done.
# Adjust the belt sander so that the belt tracks without running against the metal supports.
# Always replace washers and throat plates in their respective slots on the front of the machine when you switch accessories.

== Documentation ==
* [https://www.ridgid.com/us/en/oscillating-edge-belt-spindle-sander Links to manual and parts list]

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Matt Triano
|Matt Triano
|
|-
|Erin Kunkel
|Matt Triano
|
|-
|Tyler Matthew
|Matt Triano
|
|-
|Shae Kurko
|Matt Triano
|
|-
|Ben Bogler
|Matt Triano
|
|-
|Sam Paris
|Ron Olson
|
|-
|Knute Martell
|Ron Olson
|
|-
|Chris Kleehammer
|[[User:jason|Jason Shanfield]]
|
|-
|Trey Elliott
|[[User:jason|Jason Shanfield]]
|
|-
|Nik Brink
|[[User:jason|Jason Shanfield]]
|
|-
|Frances Ritchie
|Ron Olson
|
|-
|Ben Kern
|Ron Olson
|
|-
|Eric Yu
|Ron Olson
|
|-
|Karol Slowikowski
|Ron Olson
|
|-
|Chris Smith
|Ron Olson
|
|-
|Ryan Pierce
|Matt Triano
|
|-
|Benjamin Miller
|Ron Olson
|
|-
|Jennie P
|Ron Olson
|
|-
|Eugene Liokumovich
|Ron Olson
|
|-
|Tomas Ward
|Ron Olson
|4/26/2015
|-
|Les Schier
|Jason Shanfield
|5/2/15
|-
|Hunter Koerner
|Eric Beauchamp
|6/4/15
|-
|Erik Wessing
|Eric Beauchamp
|
|-
|Kurt Ziegel
|Eric Beauchamp
|6/4/15
|-
|Simon Pyle
|Eric Beauchamp
|6/4/15
|-
|Anthony Phelps
|Eric Beauchamp
|8/27/2015
|-
|Ralph Brendler
|Eric Beauchamp
|8/27/2015
|-
|Kyle Bieneman
|Eric Beauchamp
|8/27/2015
|-
|Jim Baker
|Eric Beauchamp
|8/27/2015
|-
|Shane Kanter
|Ron Olson
|9/12/2015
|-
|Marcin Ignasiak
|Eric Beauchamp
|
|-
|Deanna Williams
|Eric Beauchamp
|
|-
|Niko Hawley
|Eric Beauchamp
|
|-
|Kevin Mitchell
|Eric Beauchamp
|
|-
|[[User:themoffatt|Adam Moffatt]]
|Eric Beauchamp
|10/22/2015
|-
|Mike Mandrea
|Eric Beauchamp
|11/5/2015
|-
|Caleb Young
|Eric Beauchamp
|
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/03/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Shelly Loke-Gayares
|Eric Beauchamp
|1/14/16
|-
|Saul Weiner
|Eric Beauchamp
|1/14/16
|-
|Brandon Love
|Eric Beauchamp
|1/28/16
|-
|Christopher Carson
|Eric Beauchamp
|2/25/16
|-
|Jared K
|Andy L
|3/03/16
|-
|Nick Puglisi
|Eric Beauchamp
|4/21/16
|-
|Andy Muhic
|Andy Larkin
|4/28/16
|-
|Josh Younger
|Eric Beauchamp
|5/19/16
|-
|Joseph Juhnke
|Eric Beauchamp
|6/20/16
|-
|Donald Wells
|Andy Larkin
|8/4/16
|-
|[[User:mct|McTavish McArdle]]
|Andy Larkin
|2016-08-04
|-
|Joe Dowling
|Ken Burkhardt
|8/15/16
|-
|Leo Rodman
|Jason S
|9/12/16
|-
|Brian Cuocci
|Andy L
|9/15/16
|-
|Regan Via
|Ken Burkhardt
|10/17/16
|-
|Jon Komperda
|Ken Burkhardt
|10/17/16
|-
|Logan Price
|Andy Larkin
|11/21/16
|-
|Kris Blouch
|Andy Larkin
|11/21/16
|-
|Chris Ruhland
|Andy Larkin
|01/05/17
|-
|Bruce Mace
|Eric Beauchamp
|02/20/17
|-
|Matthew Quigley
|Andy Larkin
|03/02/17
|-
|Kari Danek
|Ralph Brendler
|6/15/17
|-
|Christophe Laurent
|Ralph Brendler
|8/10/17
|-
|[[User:spektre1|Danielle MacDonald]]
|Ralph Brendler
|2017-06-29
|-
|Sam Yi
|Ralph Brendler
|7/27/17
|-
|Zack Sasnow
|Paul Van Lake
|8/3/2017
|-
|Arjun Sharma
|Ralph Brendler
|8.10.17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
|Mike Thariath
|Ralph Brendler
|10/19/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Corey TOyama
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Aaron Vander Bee
|Ralph Brandler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Rolf Scheidt
|Ralph Brendler
|2/22/18
|-
|Charles Barker
|Ralph Brendler
|3/8/18
|-}
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Gary Newhouse
|Eric Beauchamp
|4/26/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
|John Burkholder
|Ralph Brendler
|5/03/18
|-
| Wayne Hendryx
| Ralph Brendler
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|David Pfeffer
|Paul V
|05/24/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Ryan Zoghlin
|Paul V
|1/16/2020
|-
|David Robbins
|Paul V
|1/16/2020
|}
[[Category:Shop Equipment]]
[[Category:Wood Shop]]

Bosch Sliding Compound Miter Saw

2020-01-18T23:10:24Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner=PS:One
|model=GCM12SD
|serial=610003177
|arrived=
|doesitwork=no
|contact=[[user: ericbeau|Eric Beauchamp]]
|where= removed
|certification=yes
|hackable=no
|value=$50.00
|image=BoschMiter.jpg
|hostarea= removed
}}

== Notes ==
Fixed. Oct 3 2018. informed from several members that the chop saw is currently unsafe to use. The guard stays up and the fences are not present.

FIXED!! Please do not use this saw until it is fixed or replaced.

replaced by MetaboHPT (formerly Hitachi) saw dec 20019 [[Miter_saw_compound_-_MetaboHPT]]

== Safety ==

== Maintenance ==
[[Bosch_Sliding_Compound_Miter_Saw_maintenance| Bosch miter saw maintenance]]

[[Category:Shop Equipment]]
[[Category:Wood Shop]]

== Authorized Proctors ==
{| class="wikitable" border="1"
|-
|Matt Triano
|-
|Jason Shanfield
|-
|Ron Olson
|-
|Eric Beauchamp
|-
|Andy Larkin
|-
|Ken Burkhardt
|-
|Ralph Brendler
|-
|Paul VanLake
|-
|Michelle DeLeon
|}

==Outside Links==

*[https://content.abt.com/documents/50981/GCM12SD_manual.pdf/93000-93999/93762.pdf User's Manual]

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Eric Beauchamp
|Danger committee
|
|-
|Sam Paris
|Andy Larkin
|
|-
| [[User:andrewvaughan|Andrew Vaughan]]
| Andy Larkin
| April 26, 2017
|-
|Paul McClay
|Ralph Brendler
|5/18/17
|-
|Jim Handley
|Ralph Brendler
|5/13/17
|-
|Zack Sasnow
|Paul Van Lake
|8/3/17
|-
|Justin Pestka
|Ralph Brendler
|8/30/17
|-
|Sam Dreyer
|Ralph Brendler
|8/30/17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
|Mike Thariath
|Ralph Brendler
|10/19/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Chinbayar Davaatseren
|Ralph Brendler
|11/2/17
|-
|Tee
|Paul V
|11/09/17
|--
|-
|Nick Fera
|Paul V
|11/09/17
|--
|[[User:frenchy|Jeremie Davis]]
|Ralph Brendler
|11/16/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Jeff Hassberger
|Ralph Brendler
|11/2/17
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Mac MacDevitt
|Paul V
|12/7/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Jamin Nollsch
|Ralph Brendler
|12/28/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Aaron Vander Bee
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Michael Ice
|Ralph Brendler
|2/08/18
|-
|Francisco Becerril
|Ralph Brendler
|2/08/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|[[User:waynr|Wayne Warren]]
|Ralph Brendler
|3/22/18
|-
|Adam Hall
|Paul V
|3/29/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Matt Maggio
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|4/19/18
|-
|Gary Newhouse
|Eric Beauchamp
|4/26/18
|-
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
|John Burkholder
|Ralph Brendler
|5/03/18
|-
| Wayne Hendryx
| Chris Iacullo
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Fritz Sullivan
| Ralph Brendler
| 5/30/18
|-
| Elizabeth Reuter
| Ralph Brendler
| 5/30/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Chris Niziolek
| Ralph Brendler
| 6/14/18
|-
| Sam Wallinga
| Ralph Brendler
| 6/14/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Berndler
| 6/14/18
|-
| Eli Schlossberg
| Ralph Brendler
| 6/14/18
|-
| Tyler Works
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Bruce Levin
| Paul V
| 7/05/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Kathryn Connolly
| Paul V
| 7/19/18
|-
| Sam Lewis
| Paul V
| 7/19/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Adam Wilk
| Ralph Brendler
| 7/26/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Earl Wood
| Paul V
| 9/13/18
|-
| Jacob Dawson
| Paul V
| 9/13/18
|-
| Ryan Treacy
| Paul V
| 9/20/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Tim Bielawa
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
|Tatjana Paunesku (tpaune)
|Ralph Brendler
|11/29/18
|-
|Deanna Musurlian
|Ralph Brendler
|01/24/19
|-
|Pat Hillegass
|Ralph Brendler
|1/24/19
|-
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Kevin Schwartzenberg
|Paul Van Lake
|03/01/19
|-
|Charlie Kepner
|Paul Van Lake
|03/01/19
|-
|Tony Green
|Ralph Brendler
|02/07/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|Zach Graceffa
|Ralph Brendler
|04/18/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|David Pfeffer
|Paul V
|05/24/19
|-
|Jack Gibbons
|Paul V
|06/20/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Luke Krudwig
|Ralph Brendler
|07/12/19
|-
|Paul Ocampo
|Ralph Brendler
|07/11/19
|-
|Andrew Soghigian
|Ralph Brendler
|07/11/19
|-
|Eric Kostecki
|Paul V
|07/18/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Sarah Lu
|Ralph Brendler
|07/25/19
|-
|Joseph Kardia
|Ralph Brendler
|08/01/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Connar Rosebraugh
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Hara Kumaran
|David Earl
|08/18/19
|-
|Steven Rummelhoff
|Ralph Brendler
|08/22/19
|-
|Mike Thompson
|Michelle DeLeon
|08/22/19
|-
|Sam Vuchetich
|Ralph Brendler
|09/05/19
|-
|Denise Allen
|Paul V
|08/29/19
|-
|Miles Hosanna
|Ralph Brendler
|09/19/2019
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|Tony Vetter
|Michelle DeLeon
|10/06/19
|-
|Drew Deitch
|Paul V
|10/31/19
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|Ryan Zoghlin
|Paul V
|1/16/2020
|}

Grizzly 6" jointer

2020-01-18T23:09:04Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS1
|certification=yes
|hackable = NO
|model = G0654
|serial = NA
|arrived = Sept 2013
|doesitwork = yes
|contact = Wood Shop Area Host
|where = Wood Shop
|value = $525.00
|hostarea = Wood Shop
|image = Jointer.jpg
}}

== Status ==
Eric fixed the broken cutter <UNSAFE to use until fixed, 1/18/2019
At least one broken indexable cutter. >

October 16 2018. Several bad gouges/chips in blades. signs of severe misuse. Please check your materials for nails etc. Repaired but just barely.

3/30/2019 The outfeed surface is out of alignment with the infeed surface, causing the work to teeter over the blades halfway down and making an uneven surface on the work (a gouge at the fulcrum point). REALIGNED..

July 2019...We have purchased a new 12 inch Jointer. Will assemble a Danger committee to devise training once it is connected to Dust Collection and power ....approx October). This is part of the Dust Collection / Shop reorganization sequence.

== Jan 2 2019 Blade guard totally loose needs spring repair BE CAREFUL ==
'''Bold text'''

purchased from Matt Triano for a song. Thank you for everything, Matt!

'''This tool requires authorization for use.'''

{{WoodshopProctors}}

== Rules ==
# Always check your wood for nails or staples. If you're not sure, check the entire piece with the metal detector or a magnet.
# Remove the smallest amount of material possible and feed it at an appropriate speed. More passes are better than fewer. If you don't know how to properly adjust the infeed table, ask for help.
# Always use the vacuum while running the jointer. Otherwise, it will clog with chips.
# If you break something, or damage the tool, contact the area host immediately. Don't let others do more damage to the machine, ruin their work, or hurt themselves by using a broken tool.
# Always vacuum the machine, cutting area, and the table around the machine when you are done.

== Documentation ==
* [http://cdn0.grizzly.com/manuals/g0654_m.pdf Manual]
* [http://cdn0.grizzly.com/partslists/g0654_pl.pdf Parts List]

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date}
|-
|Matt Triano
|Owner
|
|-
|Marcin Ignasiak
|Eric Beauchamp
|
|-
|Jason Shanfield
|Matt Triano
|
|-
|Sam Drazin
|Matt Triano
|
|-
|Eric Beauchamp
|Matt Triano
|
|-
|Ryan Pierce
|Matt Triano
|
|-
|Pete Noverini
|Matt Triano
|
|-
|Mike Coriale
|Matt Triano
|
|-
|Will Garza
|Matt Triano
|
|-
|Chris Kleehammer
|[[User:jason|Jason Shanfield]]
|
|-
|Trey Elliott
|[[User:jason|Jason Shanfield]]
|
|-
|Nik Brink
|[[User:jason|Jason Shanfield]]
|
|-
|Bradley Topol
|Matt Triano
|
|-
|Mike Jones
|Matt Triano
|
|-
|Ray Doeksen
|[[User:jason|Jason Shanfield]]
|
|-
|Hunter Koerner
|Eric Beauchamp
|
|-
|Casey Olson
|Matt Triano
|
|-
|Eugene Liokumovich
|Matt Triano
|
|-
|Jeff Smykil
|Matt Triano
|
|-
|Scott Merrell
|Eric Beauchamp
|
|-
|Erik Wessing
|Eric Beauchamp
|
|-
|Glenn Trussell
|Eric Beauchamp
|
|-
|David Gutowsky
|Eric Beauchamp
|
|-
|Szymon Sambor
|Eric Beauchamp
|9/3/15
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/15
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/15
|-
|Shine Chen
|Eric Beauchamp
|11/19/15
|-
|Mike Forkan
|Eric Beauchamp
|11/19/15
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/15
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/15
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/15
|-
|Chris Kohl
|Andy Larkin
|1/21/16
|-
|Ian McGrath
|Andy Larkin
|1/21/16
|-
|Amner Castillo
|Eric Beauchamp
|2/26/16
|-
|Christopher Carson
|Eric Beauchamp
|2/25/16
|-
|Jared K
|Andy L
|3/03/16
|-
|Keith Couture
|Eric Beauchamp
|3/10/16
|-
|Andy Muhic
|Andy Larkin
|4/28/16
|-
|Colin Campbell
|Andy L
|5/5/16
|-
|Hans Griese
|Andy L
|5/5/16
|-
|Daniel Sojka
|Andy L
|
|-
|Ken Burkhardt
|Andy Larkin
|5/5/16
|-
|An Phan
|Andy Larkin
|07/07/16
|-
|Jim Brink
|Andy Larkin
|07/21/16
|-
|Derwin Umali
|Andy Larkin
|8/7/16
|-
|Donald Wells
|Andy Larkin
|8/4/16
|-
|[[User:mct|McTavish McArdle]]
|Andy Larkin
|8/4/16
|-
|Joe Dowling
|Ken Burkhardt
|8/15/16
|-
|Simon Pyle
|Andy Larkin
|
|-
|Matt Meshulam
|Jason Shanfield
|8/24/16
|-
|Leo Rodman
|Jason S
|9/12/16
|-
|Brian Cuocci
|Andy Larkin
|9/15/16
|-
|Max Rashes
|Ken Burkhardt
|9/20/16
|-
|Revant Ohri
|Andy L
|9/15/16
|-
|Sam Paris
|Ken Burkhardt
|
|-
|Aaron Mintz
|Ken Burkhardt
|10/17/16
|-
|Brian Carstensen
|Ken Burkhardt
|10/17/16
|-
|Regan Via
|Ken Burkhardt
|10/17/16
|-
|Jon Komperda
|Ken Burkhardt
|10/17/16
|-
|Robert Richardson
|Ken Burkhardt
|10/17/16
|-
|Ryan Fiebing
|Ken Burkhardt
|10/24/16
|-
|Jack Berg
|Ken Burkhardt
|11/07/16
|-
|Logan Price
|Andy Larkin
|11/21/16
|-
|Kris Blouch
|Andy Larkin
|11/21/16
|-
|Tony Iacullo
|Andy
|12/5/16
|-
|Matt Schaid
|Andy Larkin
|01/05/17
|-
|Jamie Vollmer
|Andy Larkin
|01/05/17
|-
|John McBride
|Andy Larkin
|01/19/17
|-
|Will Heil
|Andy Larkin
|01/19/17
|-
|Dusty Buyck
|Andy Larkin
|01/19/17
|-
|Chris Ruhland
|Andy Larkin
|01/19/17
|-
|Bruce Mace
|Eric Beauchamp
|02/20/17
|-
|Matthew Quigley
|Andy Larkin
|03/02/17
|-
|W. Anthony Claypool
|Andy Larkin
|03/16/17
|-
|Crystal Morales
|Andy Larkin
|3/16/17
|-
|Jason Pittman
|Andy Larkin
|3/16/17
|-
|Ashley Borg
|Andy Larkin
|4/13/17
|-
|Sam Chen
|Andy Larkin
|
|-
|Brett Sanderson
|Ralph Brendler
|4/27/17
|-
|Crystal Zapata
|Ralph Brendler
|4/27/17
|-
|Alexa Viscius
|Ralph Brendler
|4/27/17
|-
|Andrew Vaughan
|Andy Larkin
|4/25/17
|-
|David Earl
|Ralph Brendler
|5/4/17
|-
|Paul McClay
|Ralph Brendler
|5/18/17
|-
|Luis Colmenares
|Ralph Brendler
|6/1/17
|-
|Kari Danek
|Ralph Brendler
|6/15/17
|-
|Danielle MacDonald
|Ralph Brendler
|6/29/17
|-
|Sam Yi
|Ralph Brendler
|7/27/17
|-
|Zack Sasnow
|Paul Van Lake
|8/3/17
|-
|Justin Pestka
|Ralph Brendler
|8/30/17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|Mark Haughey
|Sevin Straus
|9/30/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
|Mike Thariath
|Ralph Brendler
|10/20/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Chinbayar Davaatseren
|Ralph Brendler
|11/2/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Tee
|Paul V
|11/09/17
|--
|-
|Nick Fera
|Paul V
|11/09/17
|--
|[[User:frenchy|Jeremie Davis]]
|Ralph Brendler
|11/16/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Corey Toyama
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Jeff Hassberger
|Ralph Brendler
|11/2/17
|-
|Mac MacDevitt
|Paul V
|12/7/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Jamin Nollsch
|Ralph Brendler
|12/28/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Michael Ice
|Ralph Brendler
|2/08/18
|-
|Scott Fullman
|Ralph Brendler
|2/8/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|[[User:waynr|Wayne Warren]]
|Ralph Brendler
|3/22/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Matt Maggio
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|
|-
|4/19/18|Gary Newhouse
|Ralph Brendler
|4/26/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
| Wayne Hendryx
| Ralph Brendler
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Fritz Sullivan
| Ralph Brendler
| 5/30/18
|-
| Elizabeth Reuter
| Ralph Brendler
| 5/30/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Tyler Works
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Bruce Levin
| Paul V
| 7/05/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Kathryn Connolly
| Paul V
| 7/19/18
|-
| Sam Lewis
| Paul V
| 7/19/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Adam Wilk
| Ralph Brendler
| 7/26/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Earl Wood
| Paul V
| 9/13/18
|-
| Jacob Dawson
| Paul V
| 9/13/18
|-
| Ryan Treacy
| Paul V
| 9/20/18
|-
| Tim Bielawa
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| GWenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
|Tatjana Paunesku (tpaune)
|Ralph Brendler
|11/29/18
|-
|Jim Lund
|Paul Van Lake
|12/6/18
|-
|Deanna Musurlian
|Ralph Brendler
|01/24/19
|-
|Pat Hillegass
|Ralph Brendler
|1/24/19
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
|Tony Green
|Ralph Brendler
|02/07/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|Zach Graceffa
|Ralph Brendler
|04/18/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|David Pfeffer
|Paul V
|05/24/19
|-
|Jack Gibbons
|Paul V
|06/20/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Andrew Soghigian
|Ralph Brendler
|07/11/19
|-
|Luke Krudwig
|Ralph Brendler
|07/11/19
|-
|Patrick Cook
|Ralph Brendler
|07/11/19
|-
|Nathan Upchurch
|Ralph Brendler
|07/11/19
|-
|Paul Ocampo
|Ralph Brendler
|07/11/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Sarah Lu
|Ralph Brendler
|07/25/19
|-
|Joseph kardia
|Ralph Brendler
|08/01/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Connar Rosebraugh
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Hara Kumaran
|David Earl
|08/18/19
|-
|Steven Rummelhoff
|Ralph Brendler
|08/22/19
|-
|Mike Thompson
|Michelle DeLeon
|08/22/19
|-
|Sam Vuchetich
|Ralph Brendler
|09/05/19
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|Drew Deitch
|Paul V
|10/17/19
|-
|Adam Rangwala
|Ralph Brendler
|11/14/19
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Jeff Becker
|Eric Beauchamp
|11/23/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|David Robbins
|Paul V
|1/16/2020
|-
|Ryan Zoghlin
|Paul V
|1/16/2020
|}
[[Category:Shop Equipment]]
[[Category:Wood Shop]]
[[Category:Loaned Equipment]]

Grizzly 6" jointer

2020-01-18T23:07:27Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS1
|certification=yes
|hackable = NO
|model = G0654
|serial = NA
|arrived = Sept 2013
|doesitwork = yes
|contact = Wood Shop Area Host
|where = Wood Shop
|value = $525.00
|hostarea = Wood Shop
|image = Jointer.jpg
}}

== Status ==
Eric fixed the broken cutter <UNSAFE to use until fixed, 1/18/2019
At least one broken indexable cutter. >

October 16 2018. Several bad gouges/chips in blades. signs of severe misuse. Please check your materials for nails etc. Repaired but just barely.

3/30/2019 The outfeed surface is out of alignment with the infeed surface, causing the work to teeter over the blades halfway down and making an uneven surface on the work (a gouge at the fulcrum point). REALIGNED..

July 2019...We have purchased a new 12 inch Jointer. Will assemble a Danger committee to devise training once it is connected to Dust Collection and power ....approx October). This is part of the Dust Collection / Shop reorganization sequence.

== Jan 2 2019 Blade guard totally loose needs spring repair BE CAREFUL ==
'''Bold text'''

purchased from Matt Triano for a song. Thank you for everything, Matt!

'''This tool requires authorization for use.'''

{{WoodshopProctors}}

== Rules ==
# Always check your wood for nails or staples. If you're not sure, check the entire piece with the metal detector or a magnet.
# Remove the smallest amount of material possible and feed it at an appropriate speed. More passes are better than fewer. If you don't know how to properly adjust the infeed table, ask for help.
# Always use the vacuum while running the jointer. Otherwise, it will clog with chips.
# If you break something, or damage the tool, contact the area host immediately. Don't let others do more damage to the machine, ruin their work, or hurt themselves by using a broken tool.
# Always vacuum the machine, cutting area, and the table around the machine when you are done.

== Documentation ==
* [http://cdn0.grizzly.com/manuals/g0654_m.pdf Manual]
* [http://cdn0.grizzly.com/partslists/g0654_pl.pdf Parts List]

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date}
|-
|Matt Triano
|Owner
|
|-
|Marcin Ignasiak
|Eric Beauchamp
|
|-
|Jason Shanfield
|Matt Triano
|
|-
|Sam Drazin
|Matt Triano
|
|-
|Eric Beauchamp
|Matt Triano
|
|-
|Ryan Pierce
|Matt Triano
|
|-
|Pete Noverini
|Matt Triano
|
|-
|Mike Coriale
|Matt Triano
|
|-
|Will Garza
|Matt Triano
|
|-
|Chris Kleehammer
|[[User:jason|Jason Shanfield]]
|
|-
|Trey Elliott
|[[User:jason|Jason Shanfield]]
|
|-
|Nik Brink
|[[User:jason|Jason Shanfield]]
|
|-
|Bradley Topol
|Matt Triano
|
|-
|Mike Jones
|Matt Triano
|
|-
|Ray Doeksen
|[[User:jason|Jason Shanfield]]
|
|-
|Hunter Koerner
|Eric Beauchamp
|
|-
|Casey Olson
|Matt Triano
|
|-
|Eugene Liokumovich
|Matt Triano
|
|-
|Jeff Smykil
|Matt Triano
|
|-
|Scott Merrell
|Eric Beauchamp
|
|-
|Erik Wessing
|Eric Beauchamp
|
|-
|Glenn Trussell
|Eric Beauchamp
|
|-
|David Gutowsky
|Eric Beauchamp
|
|-
|Szymon Sambor
|Eric Beauchamp
|9/3/15
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/15
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/15
|-
|Shine Chen
|Eric Beauchamp
|11/19/15
|-
|Mike Forkan
|Eric Beauchamp
|11/19/15
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/15
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/15
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/15
|-
|Chris Kohl
|Andy Larkin
|1/21/16
|-
|Ian McGrath
|Andy Larkin
|1/21/16
|-
|Amner Castillo
|Eric Beauchamp
|2/26/16
|-
|Christopher Carson
|Eric Beauchamp
|2/25/16
|-
|Jared K
|Andy L
|3/03/16
|-
|Keith Couture
|Eric Beauchamp
|3/10/16
|-
|Andy Muhic
|Andy Larkin
|4/28/16
|-
|Colin Campbell
|Andy L
|5/5/16
|-
|Hans Griese
|Andy L
|5/5/16
|-
|Daniel Sojka
|Andy L
|
|-
|Ken Burkhardt
|Andy Larkin
|5/5/16
|-
|An Phan
|Andy Larkin
|07/07/16
|-
|Jim Brink
|Andy Larkin
|07/21/16
|-
|Derwin Umali
|Andy Larkin
|8/7/16
|-
|Donald Wells
|Andy Larkin
|8/4/16
|-
|[[User:mct|McTavish McArdle]]
|Andy Larkin
|8/4/16
|-
|Joe Dowling
|Ken Burkhardt
|8/15/16
|-
|Simon Pyle
|Andy Larkin
|
|-
|Matt Meshulam
|Jason Shanfield
|8/24/16
|-
|Leo Rodman
|Jason S
|9/12/16
|-
|Brian Cuocci
|Andy Larkin
|9/15/16
|-
|Max Rashes
|Ken Burkhardt
|9/20/16
|-
|Revant Ohri
|Andy L
|9/15/16
|-
|Sam Paris
|Ken Burkhardt
|
|-
|Aaron Mintz
|Ken Burkhardt
|10/17/16
|-
|Brian Carstensen
|Ken Burkhardt
|10/17/16
|-
|Regan Via
|Ken Burkhardt
|10/17/16
|-
|Jon Komperda
|Ken Burkhardt
|10/17/16
|-
|Robert Richardson
|Ken Burkhardt
|10/17/16
|-
|Ryan Fiebing
|Ken Burkhardt
|10/24/16
|-
|Jack Berg
|Ken Burkhardt
|11/07/16
|-
|Logan Price
|Andy Larkin
|11/21/16
|-
|Kris Blouch
|Andy Larkin
|11/21/16
|-
|Tony Iacullo
|Andy
|12/5/16
|-
|Matt Schaid
|Andy Larkin
|01/05/17
|-
|Jamie Vollmer
|Andy Larkin
|01/05/17
|-
|John McBride
|Andy Larkin
|01/19/17
|-
|Will Heil
|Andy Larkin
|01/19/17
|-
|Dusty Buyck
|Andy Larkin
|01/19/17
|-
|Chris Ruhland
|Andy Larkin
|01/19/17
|-
|Bruce Mace
|Eric Beauchamp
|02/20/17
|-
|Matthew Quigley
|Andy Larkin
|03/02/17
|-
|W. Anthony Claypool
|Andy Larkin
|03/16/17
|-
|Crystal Morales
|Andy Larkin
|3/16/17
|-
|Jason Pittman
|Andy Larkin
|3/16/17
|-
|Ashley Borg
|Andy Larkin
|4/13/17
|-
|Sam Chen
|Andy Larkin
|
|-
|Brett Sanderson
|Ralph Brendler
|4/27/17
|-
|Crystal Zapata
|Ralph Brendler
|4/27/17
|-
|Alexa Viscius
|Ralph Brendler
|4/27/17
|-
|Andrew Vaughan
|Andy Larkin
|4/25/17
|-
|David Earl
|Ralph Brendler
|5/4/17
|-
|Paul McClay
|Ralph Brendler
|5/18/17
|-
|Luis Colmenares
|Ralph Brendler
|6/1/17
|-
|Kari Danek
|Ralph Brendler
|6/15/17
|-
|Danielle MacDonald
|Ralph Brendler
|6/29/17
|-
|Sam Yi
|Ralph Brendler
|7/27/17
|-
|Zack Sasnow
|Paul Van Lake
|8/3/17
|-
|Justin Pestka
|Ralph Brendler
|8/30/17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|Mark Haughey
|Sevin Straus
|9/30/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
|Mike Thariath
|Ralph Brendler
|10/20/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Chinbayar Davaatseren
|Ralph Brendler
|11/2/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Tee
|Paul V
|11/09/17
|--
|-
|Nick Fera
|Paul V
|11/09/17
|--
|[[User:frenchy|Jeremie Davis]]
|Ralph Brendler
|11/16/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Corey Toyama
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Jeff Hassberger
|Ralph Brendler
|11/2/17
|-
|Mac MacDevitt
|Paul V
|12/7/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Jamin Nollsch
|Ralph Brendler
|12/28/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Michael Ice
|Ralph Brendler
|2/08/18
|-
|Scott Fullman
|Ralph Brendler
|2/8/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|[[User:waynr|Wayne Warren]]
|Ralph Brendler
|3/22/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Matt Maggio
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|
|-
|4/19/18|Gary Newhouse
|Ralph Brendler
|4/26/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
| Wayne Hendryx
| Ralph Brendler
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Fritz Sullivan
| Ralph Brendler
| 5/30/18
|-
| Elizabeth Reuter
| Ralph Brendler
| 5/30/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Tyler Works
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Bruce Levin
| Paul V
| 7/05/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Kathryn Connolly
| Paul V
| 7/19/18
|-
| Sam Lewis
| Paul V
| 7/19/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Adam Wilk
| Ralph Brendler
| 7/26/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Earl Wood
| Paul V
| 9/13/18
|-
| Jacob Dawson
| Paul V
| 9/13/18
|-
| Ryan Treacy
| Paul V
| 9/20/18
|-
| Tim Bielawa
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| GWenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
|Tatjana Paunesku (tpaune)
|Ralph Brendler
|11/29/18
|-
|Jim Lund
|Paul Van Lake
|12/6/18
|-
|Deanna Musurlian
|Ralph Brendler
|01/24/19
|-
|Pat Hillegass
|Ralph Brendler
|1/24/19
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
|Tony Green
|Ralph Brendler
|02/07/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|Zach Graceffa
|Ralph Brendler
|04/18/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|David Pfeffer
|Paul V
|05/24/19
|-
|Jack Gibbons
|Paul V
|06/20/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Andrew Soghigian
|Ralph Brendler
|07/11/19
|-
|Luke Krudwig
|Ralph Brendler
|07/11/19
|-
|Patrick Cook
|Ralph Brendler
|07/11/19
|-
|Nathan Upchurch
|Ralph Brendler
|07/11/19
|-
|Paul Ocampo
|Ralph Brendler
|07/11/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Sarah Lu
|Ralph Brendler
|07/25/19
|-
|Joseph kardia
|Ralph Brendler
|08/01/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Connar Rosebraugh
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Hara Kumaran
|David Earl
|08/18/19
|-
|Steven Rummelhoff
|Ralph Brendler
|08/22/19
|-
|Mike Thompson
|Michelle DeLeon
|08/22/19
|-
|Sam Vuchetich
|Ralph Brendler
|09/05/19
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|Drew Deitch
|Paul V
|10/17/19
|-
|Adam Rangwala
|Ralph Brendler
|11/14/19
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Jeff Becker
|Eric Beauchamp
|11/23/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|David Robbins
|Paul V
|1/16/2020
|-
|Ryan Zoghlin
|Paul V
|1/14/2020
|}
[[Category:Shop Equipment]]
[[Category:Wood Shop]]
[[Category:Loaned Equipment]]

Router Table (was Excalibur)

2020-01-18T23:02:41Z

Rfoto: /* List of Currently Certified Users */

== Router ==

{{Template:EquipmentPage
| image = Excalibur.jpg
|owner = PS:One
|serial =
|certification = yes
|hackable = no
|model =
|arrived =
|doesitwork = yes
|contact =
|where = Wood Shop
|hostarea = Wood Shop
|value =
}}

'''This tool requires authorization for use.'''

Excalibur Router Table <br>
http://www.general.ca/products/2_excalibur/40-200.html

manual: [[File:Excalibur_router_manual.pdf]]

Porter-Cable 7518 router

Dec 11 2018. installed digitally controlled elevator mechanism.
it is a Nextwave Ready2Rout system https://www.nextwaveautomation.com/shop/READY2LIFT%C2%AE-COMPUTERIZED-ROUTER-LIFT-p114869879

the full system manual for the Ready2Rout is here with a section on how the control panel works
https://docs.wixstatic.com/ugd/59d161_bc5568e32f0848b481e9d3f2409be158.pdf

{{WoodshopProctors}}

== List of Currently Certified Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date Certified}
|-
|Keon Turner
|Ron Olson
|10/19/15
|-
|Marcin Ignasiak
|Eric Beauchamp
|
|-
|Tim Saylor
|Danger Committee
|
|-
|Dillon Gray
|Danger Committee
|
|-
|Shawn Blaszak
|
|
|-
|Adrianna McKinley
|Tim Saylor
|
|-
|Kathy Whisler
|Tim Saylor
|
|-
|James Longfield
|Tim Saylor
|
|-
|Eric Veggeberg
|Tim Saylor
|
|-
| Madeleine Klichowski
| Tim Saylor
|
|-
| Lyn Cole
| Tim Saylor
|
|-
| Nathan Becka
| Tim Saylor
|
|-
| Brian Carstensen
| Tim Saylor
|
|-
| Matt Triano
| Tim Saylor
|
|-
|Bryan Gleason
|Matt Triano
|
|-
|Daniel Wells
|Matt Triano
|
|-
|Sean Corbett
|Matt Triano
|
|-
|Michael Skilton
|Matt Triano
|
|-
|Aaron Feigen
|Matt Triano
|
|-
|Ryan Pierce
|Dan Locks
|
|-
|John Godwim
|Matt Triano
|
|-
|Nate Hutchins
|Matt Triano
|
|-
|Jeff Molek
|Matt Triano
|
|-
|Sloan Lavery
|Matt Triano
|
|-
|Trey Keifer
|Matt Triano
|
|-
|Juan Robles
|Matt Triano
|
|-
|Simon Cygielski
|Matt Triano
|
|-
|Tom Forajter
|Matt Triano
|
|-
|Robert Grossman
|Matt Triano
|
|-
|Lucas Morris
|Matt Triano
|
|-
|Sergio Preston
|Matt Triano
|
|-
|Ron Bean
|Matt Triano
|
|-
|Greg Eagel
|Matt Triano
|
|-
|Carter Constana
|Matt Triano
|
|-
|Adam Glick
|Matt Triano
|
|-
|Zachary Fietsch
|Matt Triano
|
|-
|Solomon Hursey
|Matt Triano
|
|-
|Jesse Reynolds
|Matt Triano
|
|-
|Eduard Shlahtichman
|Matt Triano
|
|-
|Skittles Rainbow
|Matt Triano
|
|-
|Tom Jurgensen
|Matt Triano
|
|-
|Barmey Ung
|Matt Triano
|
|-
|Casey Olson
|Matt Triano
|
|-
|Jonathan Bisson
|Matt Triano
|
|-
|Bandit Gangwere
|Matt Triano
|
|-
|Joseph Nudell
|Matt Triano
|
|-
|David Butler
|Matt Triano
|
|-
|Kathryn Smiley
|Matt Triano
|
|-
|Aimee Spevak
|Matt Triano
|
|-
|Cassie Webster
|Matt Triano
|
|-
|Chris Moylan
|Matt Triano
|
|-
|Mike O'Connor
|Matt Triano
|
|-
|Tyler Hsu
|Matt Triano
|
|-
|Dee Newcum
|Matt Triano
|
|-
|Zihe "Johnson" Luo
|Matt Triano
|
|-
|Giovanni Arroyo
|Matt Triano
|
|-
|Nathan Ellis
|Matt Triano
|
|-
|Ian McLeod
|Nathan Ellis
|
|-
|Brandon Price
|Matt Triano
|
|-
|Arturo Duarte
|Matt Triano
|
|-
|Eric Braun
|Matt Triano
|
|-
|Jeremy Fay
|Matt Triano
|
|-
|Leeswann Bolden
|Matt Triano
|
|-
|James Porter
|Matt Triano
|
|-
|Jeff McBride
|Matt Triano
|
|-
|Connor Miller
|Matt Triano
|
|-
|Ashley Duca
|Matt Triano
|
|-
|Karen Niemczyk
|Matt Triano
|
|-
|Bassam Alshammari
|Matt Triano
|
|-
|John Fiene
|Matt Triano
|
|-
|Thomas Wright
|Matt Triano
|
|-
|Joseph Peltier
|Matt Triano
|
|-
|Justin Conroy
|Matt Triano
|
|-
|David Koppel
|Matt Triano
|
|-
|Sevin Straus
|Matt Triano
|
|-
|Roger Moore
|Matt Triano
|
|-
|Valerie Moore
|Matt Triano
|
|-
|Andy Schwartz
|Matt Triano
|
|-
|Assaf Evron
|Matt Triano
|
|-
|David Pelot
|Matt Triano
|
|-
|Rich Smith
|Matt Triano
|
|-
|Khoi Nguyen
|Matt Triano
|
|-
|Brian Keehner
|Matt Triano
|
|-
|Jesse Gare
|Matt Triano
|
|-
|Tyler Natoli
|Matt Triano
|
|-
|David Siegfried
|Matt Triano
|
|-
|Annie Zebula
|Matt Triano
|
|-
|Eliya Gwetta
|Matt Triano
|
|-
|Patrick Schliss
|Matt Triano
|
|-
|Arjun Wadnerkar
|Matt Triano
|
|-
|Touly Phiachantharath
|Matt Triano
|
|-
|Matt Vibberts
|Matt Triano
|
|-
|Thomas Garza
|Matt Triano
|
|-
|Will Garza
|Matt Triano
|
|-
|Brennan Koziarz
|Matt Triano
|
|-
|Alec Weege
|Matt Triano
|
|-
|Eric Beauchamp
|Matt Triano
|
|-
|Clarence Risher
|Matt Triano
|
|-
|Erica Tesla
|Matt Triano
|
|-
|Jabu Dawdu
|Matt Triano
|
|-
|Karen Murphey
|Matt Triano
|
|-
|Matt Meshulam
|Matt Triano
|
|-
|Josh Myers
|Matt Triano
|
|-
|Weston Tanner
|Matt Triano
|
|-
|Hugh Sato
|Matt Triano
|
|-
|Nora Sluzas
|Matt Triano
|
|-
|Elizabeth Koprucki
|Matt Triano
|
|-
|Oscar Villareal
|Matt Triano
|
|-
|Rob Paral
|Matt Triano
|
|-
|Alex Schaffer
|Matt Triano
|
|-
|Szymon Sambor
|Matt Triano
|
|-
|Michael Solhelm
|Matt Triano
|
|-
|[[User:lucas|Lucas Goossen]]
|Matt Triano
|
|-
|[[User:Mwilkens|Matt Wilkens]]
|Matt Triano
|
|-
|Eric Slehofer
|Matt Triano
|
|-
|Jon Levine
|Matt Triano
|
|-
|Melody Snyder
|Matt Triano
|
|-
|Curtis Cooke
|Matt Triano
|
|-
|Harry Morgan
|Matt Triano
|
|-
|Sam Drazin
|Matt Triano
|
|-
|Mike Kislovsky
|Matt Triano
|
|-
|Keven Kalay
|Matt Triano
|
|-
|Sam Reicks
|Ron Olson
|
|-
|Kevin Pulver
|Ron Olson
|
|-
|Cary Lahucik
|Ron Olson
|
|-
|Keith Hultman
|Ron Olson
|
|-
|Mario Rodriguez
|Ron Olson
|
|-
|John Keippel
|Ron Olson
|
|-
|Szilvia Precsinszki
|Ron Olson
|
|-
|Davis Mazariegos
|Ron Olson
|
|-
|Pete Noverini
|Matt Triano
|
|-
|Mike Coriale
|Matt Triano
|
|-
|Dan Baltudis
|Ron Olson
|
|-
|David Fell
|Ron Olson
|
|-
|Dubi Kaufmann
|Ron Olson
|
|-
|Patrick Grider
|Ron Olson
|
|-
|Tyler Matthew
|Matt Triano
|
|-
|Shae Kurko
|Matt Triano
|
|-
|John Farmer
|Ron Olson
|
|-
|Sam Paris
|Ron Olson
|
|-
|Frances Ritchie
|Ron Olson
|
|-
|Ben Kern
|Ron Olson
|
|-
|Eric Yu
|Ron Olson
|
|-
|Knute Martell
|Ron Olson
|
|-
|Karol Slowikowski
|Ron Olson
|
|-
|Chris Smith
|Ron Olson
|
|-
|Benjamin Miller
|Ron Olson
|
|-
|Jennie P
|Ron Olson
|
|-
|Eugene Liokumovich
|Ron Olson
|
|-
|Laurel Garrett
|Matt Triano
|
|-
|Rei Kevin
|Matt Triano
|
|-
|Aji Slater
|Matt Triano
|
|-
|John Beyer
|Matt Triano
|
|-
|Brad Topol
|Matt Triano
|
|-
|[[User:papaben44|Benjamin Dambman]]
|Matt Triano
|4/14/2015
|-
|Tomas Ward
|Ron Olson
|4/26/2015
|-
|Les Schier
|Jason Shanfield
|5/2/15
|-
|Andy Richardson
|Matt Triano
|4/14/15
|-
|Erik Wessing
|Eric Beauchamp
|
|-
|Ray Doeksen
|Eric Beauchamp
|
|-
|Ryan Neuman
|Ron Olson
|
|-
|Anthony Phelps
|Eric Beauchamp
|8/27/2015
|-
|Ralph Brendler
|Eric Beauchamp
|8/27/2015
|-
|Jim Baker
|Eric Beauchamp
|8/27/2015
|-
|Kyle Bieneman
|Ron Olson
|
|-
|Glenn Powers
|Jason Shanfield
|10/18/2015
|-
|Niko Hawley
|Eric Beauchamp
|
|-
|Kevin Mitchell
|Eric Beauchamp
|
|-
|[[User:themoffatt|Adam Moffatt]]
|Eric Beauchamp
|10/22/2015
|-
|Jean Michel Crettaz
|Eric Beauchamp
|10/22/2015
|-
|Caleb Young
|Eric Beauchamp
|
|-
|Peter Letscher
|Eric Beauchamp
|11/05/15
|-
|Glenn Trussell
|Eric Beauchamp
|11/05/2015
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Shine Chen
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/03/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Chris Kohl
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Peter Brask
|Eric Beauchamp
|1/14/16
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
|Shelly Loke-Gayares
|Eric Beauchamp
|1/14/16
|-
|Christopher Carson
|Eric Beauchamp
|2/25/16
|-
|Jared K
|Andy L
|3/03/16
|-
|Brian Cuocci
|Andy L
|3/17/16
|-
|Julie Zwolinski
|Eric Beauchamp
|3/24/16
|-
|Nick Puglisi
|Eric Beauchamp
|4/21/16
|-
|Andy Muhic
|Andy Larkin
|4/28/16
|-
|Colin Campbell
|Andy L
|5/5/16
|-
|Hans Griese
|Andy Larkin
|5/5/16
|-
|Spencer Simms
|Eric Beauchamp
|05/19/2016
|-
|Josh Younger
|Eric Beauchamp
|5/19/16
|-
|Ian Monroe
|Eric Beauchamp
|5/19/16
|-
|Joseph Juhnke
|Eric Beauchamp
|6/20/16
|-
|Donald Wells
|Andy Larkin
|8/4/16
|-
|An Phan
|Andy Larkin
|7/7/16
|-
|Derwin Umali
|Andy Larkin
|8/4/16
|-
|Simon Pyle
|Andy Larkin
|
|-
|Max Rashes
|Ken Burkhardt
|9/20/16
|-
|Logan Price
|Andy Larkin
|11/21/16
|-
|Kris Blouch
|Andy Larkin
|11/21/16
|-
|Tony Iacullo
|Andy
|12/5/16
|-
|Matt Schaid
|Andy Larkin
|01/05/17
|-
|Jamie Vollmer
|Andy Larkin
|01/05/17
|-
|Chris Ruhland
|Andy Larkin
|01/05/17
|-
|John McBride
|Andy Larkin
|01/19/17
|-
|Will Heil
|Andy Larkin
|01/19/17
|-
|Dusty Buyck
|Andy Larkin
|01/19/17
|-
|Ashley Borg
|Andy Larkin
|4/13/17
|-
| [[User:Andrewvaughan|Andrew Vaughan]]
| Andy Larkin
| 2017-04-25
|-
|Molly Adamski
|Ralph Brendler
|4/27/17
|-
|Shabab Mustafa
|Ralph Brendler
|4/27/17
|-
|Brett Sanderson
|Ralph Brendler
|4/27/17
|-
|Crystal Zapata
|Ralph Brendler
|4/27/17
|-
|Alexa Viscius
|Ralph Brendler
|4/27/17
|-
|David Earl
|Ralph Brendler
|5/4/2017
|-
|Paul McClay
|Ralph Brendler
|5/18/17
|-
|Kari Danek
|Ralph Brendler
|6/16/17
|-
| [[User:spektre1|Danielle MacDonald]]
| Ralph Brendler
| 2017-06-29
|-
|Zack Sasnow
|Paul Van Lake
|8/3/17
|-
|Arjun Sharma
|Ralph Brendler
|8.10.17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|Sam Dreyer
|Ralph Brendler
|8/30/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
|Mike Thariath
|Ralph Brendler
|10/19/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Tee
|Paul V
|11/09/17
|--
|-
|Nick Fera
|Paul V
|11/09/17
|--
|[[User:frenchy|Jeremie Davis]]
|Ralph Brendler
|11/16/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Corey TOyama
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Jeff Hassberger
|Ralph Brendler
|11/2/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Jamin Nollsch
|Ralph Brendler
|12/28/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brendler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Michael Ice
|Ralph Brendler
|2/08/18
|-
|Scott Fullman
|Ralph Brendler
|2/08/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Rolf Scheidt
|Ralph Brendler
|2/22/18
|-}
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|[[User:waynr|Wayne Warren]]
|Ralph Brendler
|3/22/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Matt Maggio
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|4/19/18
|-
| Wayne Hendryx
| Chris Iacullo
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Fritz Sullivan
| Ralph Brendler
| 5/30/18
|-
| Elizabeth Reuter
| Ralph Brendler
| 5/30/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Chris Niziolek
| Ralph Brendler
| 6/14/18
|-
| Sam Wallinga
| Ralph Brendler
| 6/14/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Eli Schlossberg
| Ralph Brendler
| 6/14/18
|-
| Tyler Works
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Adam Wilk
| Ralph Brendler
| 7/26/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
| Will Brown
| Ralph Brendler
| 10/31/18
|-
|Tatjana Paunesku (tpaune)
|Ralph Brendler
|11/29/18
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Kevin Schwartzenberg
|Paul Van Lake
|03/01/19
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
| Tony Green
| Ralph Brendler
| 02/07/19
|-
|Bobby Salazar
|Ralph Brendler
|03/21/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|Zach Graceffa
|Ralph Brendler
|04/18/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Nathan Upchurch
|Ralph Brendler
|07/11/19
|-
|Luke Krudwig
|Ralph Brendler
|07/11/19
|-
|Andrew Soghigian
|Ralph Brendler
|07/11/19
|-
|Paul Ocampo
|Ralph Brendler
|07/11/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Joseph Kardia
|Ralph Brendler
|08/01/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Hara Kumaran
|David Earl
|08/18/19
|-
|Steven Rummelhoff
|Ralph Brendler
|08/22/19
|-
|Mike Thompson
|Michelle DeLeon
|08/22/19
|-
|Denise Allen
|Paul V
|08/29/19
|-
|Sam Vuchetich
|Ralph Brendler
|09/05/19
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|Drew Deitch
|Paul V
|10/17/19
|-
|Nikolas Gamarra
|Ralph Brendler
|10/13/19
|-
|Adam Rangwala
|Ralph Brendler
|11/14/19
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|David Robbins
|Paul V
|1/18/2020
|-
|Ryan Zoghlin
|Paul V
|1/14/2020
|}
[[Category:Shop Equipment]]
[[Category:Fabrication]]
[[Category:Wood Shop]]

Sander (oscillating spindle) - Steel City

2020-01-18T22:58:03Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = No
|model = Steel City Tool Works 55200 Oscillating Spindle Sander
|serial = SERIAL NUMBER
|arrived = ?
|doesitwork = yes
|contact = Eric Beauchamp
|where = Sanding and routing area south wall
|value = $900 ??
|hostarea = Wood Shop
|image = SC spindle sanderL.jpg
}}

== NOTE ==
Eric has diagnosed and ordered parts Sept 2018

Fixed it but then oscillating function failed in spring 2019 again. Usable as spindle

12/7/2019 table unstable need to diagnose

= Maintenance =

== Maintenance Log ==
{| class="wikitable" border="1"
!Date
!Preformed by
!Service Type
!Notes
|-
|8/2018
|EB
|stopped oscillating.
|EB fixed december.
|-
|jan 2 2019
| Zac and gary
|stopped oscillating again.
|
|-
|}

== Outstanding Maintenance Issues ==

=== gearbox being repaired FIXED nov or dec? 2018 broken again jan 2019

== Rules ==

# If you break something, or damage the tool, contact the area host immediately. Don't let others do more damage to the machine, ruin their work, or hurt themselves by using a broken tool.
# Always vacuum the machine, cutting area, and the table around the machine when you are done.

== Documentation ==
* manual [https://images.homedepot-static.com/catalog/pdfImages/e4/e433b76b-3318-46e6-a1a2-f25f5606431e.pdf]

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|<please add>
|<please add>
|-
|gary newhouse
|Eric Beauchamp
|4/26/18
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|David Robbins
|Paul V
|1/16/2020
|-
|Ryan Zoghlin
|Paul V
|1/14/2020
|}

[[Category:Shop Equipment]]
[[Category:Wood Shop]]

Bosch Sliding Compound Miter Saw

2020-01-18T21:36:09Z

Rfoto: /* List of Currently Authorized Users */

Supermax 25x2 Drum Sander

2020-01-18T21:29:54Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner=PS:One
|model=25x2
|serial=?
|arrived=
|doesitwork=no
|contact=[[user: ericbeau|Eric Beauchamp]]
|where=Wood Shop
|certification=yes
|hackable=no
|value=$2700
|image=SupermaxSander.jpg
|hostarea=Wood Shop
}}

== Status ==
Aug 30 2018 Eric B installed new motor and starter capacitor..
'''
DO NOT OPEN HOOD''' to push start as we did in recent past. Just push start button and adjust feed speed.

Stay tuned for more detailed instructions for use.

12/7/2019 feed conveyor belt is destroyed. quite worn belt was running off center and tore itself apart. replacement being ordered.

== Authorization ==

Authorization required. Part of the WoodShop overall authorization. See the PS1 calendar for future dates.

== Usage Notes ==

*For oily or dense woods (tropical hardwoods, etc), take only very light passes to prevent clogging the sandpaper.

*Use a belt cleaner occasionally to refresh the sandpaper

== Safety ==

This sander features overload detection. If the machine detects too high a load, it will automatically slow down the feed. This saves wear and tear on the machine, but may cause burning of the workpiece if you cut too aggressively.

*The height adjustment on this machine is VERY aggressive. A full turn will raise the table by more than 2mm (a typical cut should be < .5mm). '''PLEASE USE A MAXIMUM OF 1/8 TURN OF THE HEIGHT WHEEL PER PASS!'''

* Make your first cuts with a very slow speed (10 or less). Once you are sure the load is OK you can gradually increase the speed on subsequent passes.

*When overload detection kicks in, a red light next to the speed control will turn on. '''IF YOU SEE THIS LIGHT, PLEASE REDUCE YOUR DEPTH OF CUT AND/OR FEED RATE!'''

*Like all of our other sanders, sleeves must be above the elbow, and no gloves should be worn. It's pretty easy to get pulled into the rollers.

== Description ==

* Sanding Capacity:
** Maximum Width (in): 25
** Minimum Length (in): 3-1/2
** Minimum Thickness (in): 1/32
* Drum Speed: 1740 RPM
* Dust Hood: 1000 CFM recommended

==External Links==

*[http://www.supermaxtools.com/products/wood/25x2-double-drum-sander Manufacturer's Page]
*[http://www.supermaxtools.com/wp-content/uploads/25x2_37x2-10-2015.pdf Owner's Manual]

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date}
|-
|Eric Beauchamp
|Danger committee
|6/23/2017
|-
|Ralph Brendler
|Danger committee
|6/23/2017
|-
|Paul van Lake
|Danger committee
|6/23/2017
|-
|Zack Sasnow
|Jason Shanfield
|8/27/17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|Jared K
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brandler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Michael Ice
|Ralph Brendler
|2/08/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Rolf Scheidt
|Ralph Brendler
|2/22/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Nick Prorok
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|[[User:waynr|Wayne Warren]]
|Ralph Brendler
|3/22/18
|-
|Adam Hall
|Paul V
|3/29/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|4/19/18
|-
|4/19/18|Gary Newhouse
|Ralph Brendler
|4/26/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
| Wayne Hendryx
| Ralph Brendler
| 4/19/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Sam Wallinga
| Ralph Brendler
| 6/14/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Eli Schlossberg
| Ralph Brendler
| 6/14/18
|-
| Tyler Works
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Bruce Levin
| Paul V4
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Kathryn Connolly
| Paul V
| 7/19/18
|-
| Sam Lewis
| Paul V
| 7/19/18
|-
| Sam Paris
| Ralph Brendler
| 9/2/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
| Will Brown
| Ralph Brendler
| 10/31/18
|-
|Tatjana Paunesku (tpaune)
|Ralph Brendler
|11/29/18
|-
|Jim Lund
|Paul Van Lake
|12/7/18
|-
|Deanna Musurlian
|Ralph Brendler
|01/24/19
|-
|Pat Hillegass
|Ralph Brendler
|1/24/19
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Kevin Schwartzenberg
|Paul Van Lake
|03/01/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|Zach Graceffa
|Ralph Brendler
|4/18/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|Jack Gibbons
|Paul V
|06/20/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Patrick Cook
|Ralph Brendler
|07/11/19
|-
|Patrick Cook
|Ralph Brendler
|07/11/19
|-
|Nathan Upchurch
|Ralph Brendler
|07/11/19
|-
|Andrew Soghigian
|Ralph Brendler
|07/11/19
|-
|Luke Krudwig
|Ralph Brendler
|07/11/19
|-
|Paul Ocampo
|Ralph Brendler
|07/11/19
|-
|Sarah Lu
|Ralph Brendler
|07/25/19
|-
|Joseph Kardia
|Ralph Brendler
|08/01/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Connar Rosebraugh
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Steven Rummelhoff
|Ralph Brendler
|08/22/19
|-
|Denise Allen
|Paul V
|08/29/19
|-
|Sam Vuchetich
|Ralph Brendler
|09/05/19
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|Adam Rangwala
|Ralph Brendler
|11/14/19
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Adam Keim
|Ralph Brendler
|11/14/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Ryan Zoghlin
|Paul V
|1/14/2020
|}
[[Category:Shop Equipment]]
[[Category:Wood Shop]]

Dayton 6x9 Belt Sander

2020-01-18T21:28:19Z

Rfoto: /* List of Currently Certified Users */

SawStop table saw

2020-01-18T21:22:44Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|certification=yes
|hackable = NO
|model = Model PCS31230 3.0HP 220V
|serial = P114010835
|arrived = 9/1/2012
|doesitwork = yes
|contact = Wood Shop Area Host
|where = Wood Shop
|value = $3,000.00
|image = SawStop.jpg
|hostarea = Wood Shop
}}
[[File:Saw stop badge.jpg|thumb|right|200px]]

= Authorization for this tool by authorized proctors only =
== Authorized Proctors ==
{| class="wikitable" border="1"
|-
|Ron Olson
|-
|Eric Beauchamp
|-
|Ralph Brendler
|-
|Paul VanLake
|-
|Michelle DeLeon
|}

== Status ==

Repaired and in working order as of 11/9/2015

oops on 9/30/2018, someone reported on googlegroups that Chalkpaper on ply wood caused the brake to engage..

10-5-18 reports of Elevator not working

Repaired and in working order as of 11/9/2015

may 14 2018 brake triggered by lasered wood

june 16 2018 tilt broken

Repaired--9/30/2018, someone reported on googlegroups that Chalkpaper on ply wood caused the brake to engage..

7/1/2018 tilt broken

10-5-18 tilt and Elevator not working Parts ordered.

10/24/2018 everything put back together and the lift and tilt mechanisms work mostly like a charm.still waiting for pinion gear to optimize it, but is again functional..

11-17-2018 repaired. 11/16/2018. Brake tripped by user holding a graphite pen in hand while running saw. Pencil made blade contact with blade

2/12/2019. Ashley ordered and David E replaces brake and blade. 2/11/2019. bladeBrake tripped again new on order

3/3/2019. David earl repaired finniky switch. Repaired / adjusted spring and it’s mounts, re-mounted loose control PCB

4/7/2019. Elevator not working 4/9/2019 Eric repaired. Still a little hard to turn but working. 8/24. Brake engaged. Out of service

8/25/19. Saw is back in service. The dado stack will be out until we received the replacement brake

9/14/19. The angle adjustment is not working.
It is at 5 degrees currently and when trying to turn it, the gears sort of clunk and sets it back at 5. —david p.

9/16/19 working ok today thanks to whoever fixed it gary

10/26/19 Eric replaced brake

11/11/2019 Tilt mechanism broken DO NOT TILT BLADE. Gear stripped. Saw still usable in 90 degree cuts.

== How to Become an Authorized Proctor ==

Contact Wood Shop Area Host Eric Beauchamp.

= Rules =
# Do not move the machine ever.
# Never use the table as a work surface.
# Always have the dust collection on. Turn it on before you plug in the saw and off after you unplug the saw.
# Always check your material on the blade before you spin up the blade. If the light turns red, DO NOT CUT.
# Always check your wood for nails or staples. If you're not sure, check the entire piece with a magnet.
# If you break something, or damage the saw, contact the area host immediately. Don't let others do more damage or hurt themselves by using a broken tool.
# Always dust the entire machine when you are done. Also check the motor compartment after every use and vacuum out as needed.

= Additional Information =

== Dado Stack ==
Dado stack use requires separate authorization.

SawStop saws support 8″ dado sets only. The optional dado brake cartridge must be used for dado cuts. It has a larger brake pawl designed to stop the multiple blades in a dado set. In addition, you will also need to use a zero-clearance insert specifically for the dado set.

http://www.rockler.com/sawstop-dado-brake-cartridge-for-cns-table-saws

== Sacrificial Fence ==

The Sacrificial Fence requires the dado stack authorization to have been completed.

A sacrificial fence is used in combination with the dado stack to create rebates (grooves) at the edges of boards. Trying to make a rebate at the edge of a board without a sacrificial fence in place will result in damage to the rip fence.

The sacrificial fence is placed on top of the standard table saw rip fence and secured with the screws on the back side. Ensure that the fence is square to the table while tightening the set screws, and that the fence is flush with the front of the rip fence. Then, slide the fence over top of the dado stack, adjusting the fence for the desired rebate width. Adjust the blade height for the desired depth of rebate.

See: https://www.youtube.com/watch?v=JYqvwlbm6B0 beginning at minute 8 for a demonstration of how the sacrificial fence works.

== Blade Brake ==

This saw is equipped with a safety feature that will (hopefully) stop the blade when it contacts something conductive-- like your hand. However, that means you normally can't cut conductive things with this saw or you will trigger the safety brake. This is good if it was your hand in the way, but it also destroys the sawblade and requires installation of a replacement part that costs $70+ every time. And the saw will be down until the replacement can be installed.

According to the owner's manual: "Conductive materials such as aluminum and other metals, carbon fiber materials, '''mirrored acrylic''', carbon-filled materials, etc. will typically '''cause the brake to activate'''." [Emphasis added.]

Other things that may trigger the brake include wet wood, and wood with embedded nails or staples. Lexan and green pressure-treated wood reportedly can also be a problem. That is why the rules instruct you to check your material on the side of the blade before spinning it up, and to check your wood for nails or staples!

== Notes ==
* There's an m8 hole drilled and tapped in the mitre gauge. The post from a magnetic base of our dial indicators thread in. The post may require a spacer so the threads don't stick out (use a stack of washers or a larger-than-m8 nut).
* The right hand table adjusting screw was bent while aligning the table. The table was aligned without it. Aligning the arbor tilt axis will be *really tough* without a replacement. (Part #11 in the cabinet and table exploded diagram in the manual p98)
* The rear rip fence rail has places to put 4 countersunk allen bolts. The left hand bolt screwed into the main table was too long and made contact with an internal table part (probably the rear trunion). It probably pushed the table out of alignment and caused binding while re-aligning the table. That bolt was left out. Don't replace it!

== Training Links ==
* [http://www.sawstop.com/images/uploads/manuals/PCS%20Owners%20Manual%20Model%20PCS31230%20V5.0%2009-13.pdf Owner's Manual]

== Use checklist ==

PS1 is experimenting with the use of checklists to encourage the safe use and proper care of tools in the workspace. The latest version of the [[checklists]] for this tool is stored as a [https://docs.google.com/document/d/1zxrvQX0DXaLxaXkaKCKpZ-PAgnDak6ezKKBkdu_Fw1U/edit?usp=sharing Google Doc] that can be edited by anyone. If you make changes, update the effective date at the bottom of the document. Print a new copy, and replace the old one.

== Maintenance ==
* [http://web.archive.org/web/20130224091815/http://www.woodworkersjournal.com/Main/Articles/Table_Saw_Maintenance_Skill_Builder_Power_Tool_Tun_8197.aspx Table Saw Maintenance]
* [[SawStop Table Saw maintenance|maintenance page]]

== List of Currently Authorized Users ==
{|Class="wikitable sortable" border="1" style="td { border: 1px solid #000000}"
|-
! Member !! Authorizer !! Date
|-
|-
|Dan Meyer || Sean Blaszak || prior to 2015
|-
|Eric Stein || Steve Finkelman / Danger Committee || prior to 2015
|-
|Dee Newcum || Shawn Blaszak || prior to 2015
|-
|Steve Farkas || Adrianna McKinley || prior to 2015
|-
|Mike Warot || Adrianna McKinley || prior to 2015
|-
|Ryan Pierce || Adrianna McKinley || prior to 2015
|-
|Sean Nixon || Tim Saylor || prior to 2015
|-
|Michael Reddy || Tim Saylor || prior to 2015
|-
|Derek Bever || Tim Saylor || prior to 2015
|-
|Dan Willmott || Tim Saylor || prior to 2015
|-
|Michael Skilton || Adrianna McKinley || prior to 2015
|-
|João Santos || Geoffrey Topham || prior to 2015
|-
|David Fell || Tucker Tomlinson || prior to 2015
|-
|Dan Locks || Adrianna McKinley || prior to 2015
|-
|Dave Earley || Dan Locks || prior to 2015
|-
|Lyn Cole || Tim Saylor || prior to 2015
|-
|George Shaw || Tim Saylor || prior to 2015
|-
|Hilary Lee || Matt Triano || prior to 2015
|-
|Daylan Dufelmeier || Matt Triano || prior to 2015
|-
|Bryan Gleason || Matt Triano || prior to 2015
|-
|Daniel Wells || Matt Triano || prior to 2015
|-
|Aaron Feigen || Matt Triano || prior to 2015
|-
|Lawrence MacDevitt || Matt Triano || prior to 2015
|-
|Ryan Kelly || Matt Triano || prior to 2015
|-
|Ron Bean || Matt Triano || prior to 2015
|-
|Jonathan Bisson || Matt Triano || prior to 2015
|-
|Anna Yu || Matt Triano || prior to 2015
|-
|Bandit Gangwere || Matt Triano || prior to 2015
|-
|David Butler || Matt Triano || prior to 2015
|-
|Ian McLeod || Derek Bever || prior to 2015
|-
|Jeremy Fay || Matt Triano || prior to 2015
|-
|Justin Conroy || Matt Triano || prior to 2015
|-
|Sevin Straus || Matt Triano || prior to 2015
|-
|Ray Doeksen || Jason Shanfield || prior to 2015
|-
|Touly Phiachantharath || Matt Triano || prior to 2015
|-
|Will Garza || Matt Triano || prior to 2015
|-
|Brennan Koziarz || Matt Triano || prior to 2015
|-
|Eric Beauchamp || Matt Triano || prior to 2015
|-
|Josh Myers || Matt Triano || prior to 2015
|-
|Elizabeth Koprucki || Matt Triano || prior to 2015
|-
|Alex Schaffer || Matt Triano || prior to 2015
|-
|Szymon Sambor || Matt Triano || prior to 2015
|-
|Lucas Goossen || Matt Triano || prior to 2015
|-
|John Keippel || Ron Olson || prior to 2015
|-
|Pete Noverini || Matt Triano || prior to 2015
|-
|Dan Baltudis || Ron Olson || prior to 2015
|-
|Ben Bogler || Matt Triano || prior to 2015
|-
|Sam Paris || Matt Triano || prior to 2015
|-
|Bob McGrath || Ron Olson || prior to 2015
|-
|Michelle Deleon || Ron Olson || prior to 2015
|-
|Jennie P || Ron Olson || prior to 2015
|-
|Eugene Liokumovich || Ron Olson || prior to 2015
|-
|John Beyer || Matt Triano || prior to 2015
|-
|Erik Wessing || Eric Beauchamp || prior to 2015
|-
|Marcin Ignasiak || Eric Beauchamp || prior to 2015
|-
|Abel Greenwald || Andy Larkin || prior to 2015
|-
|Glenn Powers || Matt Triano || Mar/01/2015
|-
|Mike Jones || Matt Triano || May/12/2015
|-
|Mark Stevens || Eric Beauchamp || Jul/18/2015
|-
|Ralph Brendler || Eric Beauchamp || Aug/27/2015
|-
|Shane Kanter || Ron Olson || Sep/10/2015
|-
|Burton Kent || Ron Olson || Sep/10/2015
|-
|Jeff Smykil || Matt Triano || Sep/26/2015
|-
|John McDonald || Eric Beauchamp || Oct/05/2015
|-
|Aaron Carlock || Eric Beauchamp || Nov/19/2015
|-
|Patrick Lynch || Eric Beauchamp || Nov/19/2015
|-
|Alex Al-Hamdan || Eric Beauchamp || Dec/04/2015
|-
|Jared K. || Eric Beauchamp || Mar/10/2016
|-
|Mark Zumwalt || Andy Larkin || Mar/17/2016
|-
|Adam Stein || Andy Larkin || Apr/14/2016
|-
|Greg "Nerobro" Teiber || Dan Locks || Apr/29/2016
|-
|Spencer Simms || Eric Beauchamp || May/19/2016
|-
|Jim Brink || Andy Larkin || Jul/21/2016
|-
|Derwin Umali || Andy Larkin || Aug/04/2016
|-
|Joe Dowling || Ken Burkhardt || Aug/15/2016
|-
|Revant Ohri || Andy L || Sep/15/2016
|-
|Max Rashes || Ken Burkhardt || Sep/20/2016
|-
|Jon Komperda || Ken Burkhardt || Oct/17/2016
|-
|Logan Price || Andy Larkin || Nov/21/2016
|-
|Tony Iacullo || Andy || Dec/05/2016
|-
|John McBride || Andy Larkin || Jan/19/2017
|-
|Bruce Mace || Eric Beauchamp || Feb/20/2017
|-
|Matthew Quigley || Andy Larkin || Mar/02/2017
|-
|Molly Adamski || Ralph Brendler || Apr/27/2017
|-
|David Earl || Ralph Brendler || May/04/2017
|-
|Jim Handley || Ralph Brendler || May/13/2017
|-
|Paul McClay || Ralph Brendler || May/18/2017
|-
|Kari Danek || Ralph Brendler || Jun/15/2017
|-
|Danielle MacDonald || Ralph Brendler || Jun/29/2017
|-
|Andrew Wingate || Jason Shanfield || Jul/22/2017
|-
|Zack Sasnow || Paul Van Lake || Aug/03/2017
|-
|Christophe Laurent || Ralph Brendler || Aug/10/2017
|-
|Jacob Snyder || Ralph Brendler || Sep/07/2017
|-
|Mark Haughey || Sevin Straus || Sep/30/2017
|-
|Theo T || Ralph Brendler || Nov/30/2017
|-
|Wally Ibrahim || Ralph Brendler || Nov/30/2017
|-
|Sam Holtman || Paul V || Dec/06/2017
|-
|Ben Starett || Ralph Brendler || Dec/14/2017
|-
|Ross Hanchett || Ralph Brendler || Dec/14/2017
|-
|Michael Donovan || Ralph Brendler || Dec/14/2017
|-
|Jamin Nollsch || Ralph Brendler || Dec/28/2017
|-
|Aaron Vander Bee || Ralph Brandler || Jan/11/2018
|-
|Ben Farmer || Ralph Brendler || Jan/11/2018
|-
|Joseph Crouch || Ralph Brendler || Jan/11/2018
|-
|Bradford Smith || Ralph Brendler || Jan/11/2018
|-
|Stephanie Pelzer || Ralph Brendler || Jan/11/2018
|-
|Amanda Assaley || Ralph Brendler || Jan/11/2018
|-
|Chris Eppig || Ralph Brendler || Jan/11/2018
|-
|Patrick Smith || Ralph Brendler || Jan/11/2018
|-
|Jeff Gershune || Paul VanLake || Jan/16/2018
|-
|Bryan Pennington || Ralph Brendler || Jan/25/2018
|-
|Michael Ice || Ralph Brendler || Feb/08/2018
|-
|Francisco Becerril || Ralph Brendler || Feb/08/2018
|-
|Brandon Kennedy || Ralph Brendler || Feb/22/2018
|-
|Rolf Scheidt || Ralph Brendler || Feb/22/2018
|-
|Charles Barker || Ralph Brendler || Mar/08/2018
|-
|Dan Mach || Ralph Brendler || Mar/08/2018
|-
|Bruce Mace || Ralph Brendler || Mar/08/2018
|-
|Nick Prorok || Ralph Brendler || Mar/08/2018
|-
|Ricardo Staudt || Ralph Brendler || Mar/08/2018
|-
|Paul Graham || Ralph Brendler || Mar/22/2018
|-
|Mike Gucciard || Ralph Brendler || Mar/22/2018
|-
|Wayne Warren || Ralph Brendler || Mar/22/2018
|-
|Adam Hall || Paul V || Mar/29/2018
|-
|Bill Schroeder || Ralph Brendler || Apr/05/2018
|-
|Mike Wilkin || Ralph Brendler || Apr/19/2018
|-
|Alex Lanigan || Ralph Brendler || Apr/19/2018
|-
|Jessica Jokhi || Ralph Brendler || Apr/19/2018
|-
|Matt Maggio || Ralph Brendler || Apr/19/2018
|-
|Jonathan Frink || Ralph Brendler || Apr/19/2018
|-
|Ian Brieger || Ralph Brendler || Apr/19/2018
|-
|Wayne Hendryx || Ralph Brendler || Apr/19/2018
|-
|Gary Newhouse || Ralph Brendler || Apr/26/2018
|-
|Dave DesRoberts || Paul Van Lake || Apr/26/2018
|-
|Jennifer DesRoberts || Paul Van Lake || Apr/26/2018
|-
|John Burkholder || Ralph Brendler || May/03/2018
|-
|Brendan Fortune || Ralph Brendler || May/17/2018
|-
|Fritz Sullivan || Ralph Brendler || May/30/2018
|-
|Elizabeth Reuter || Ralph Brendler || May/30/2018
|-
|Kirsten Landmark Masih || Ralph Brendler || Jun/07/2018
|-
|Chris Niziolek || Ralph Brendler || Jun/14/2018
|-
|Bob Fritz || Ralph Brendler || Jun/14/2018
|-
|Sam Wallinga || Ralph Brendler || Jun/14/2018
|-
|Nate Myren || Ralph Brendler || Jun/14/2018
|-
|Eli Schlossberg || Ralph Brendler || Jun/14/2018
|-
|Tyler Works || Ralph Brendler || Jun/14/2018
|-
|Bruce Levin || Paul V || Jul/05/2018
|-
|Joe Day || Paul V || Jul/05/2018
|-
|Mike Yacobucci || Ralph Brendler || Jul/12/2018
|-
|Mike Yacobucci || Ralph Brendler || Jul/12/2018
|-
|Aaron Hale || Ralph Brendler || Jul/26/2018
|-
|Adam Wilk || Ralph Brendler || Jul/26/2018
|-
|Adam Wilk || Ralph Brendler || Jul/26/2018
|-
|Adam Wilk || Ralph Brendler || Jul/26/2018
|-
|Aaron Hale || Ralph Brendler || Jul/26/2018
|-
|Geoff Klein || Paul V || Sep/13/2018
|-
|Earl Wood || Paul V || Sep/13/2018
|-
|Jacob Dawson || Paul V || Sep/13/2018
|-
|Jacob Dawson || Paul V || Sep/13/2018
|-
|Geoff Klein || Paul V || Sep/13/2018
|-
|Geoff Klein || Paul V || Sep/13/2018
|-
|Earl Wood || Paul V || Sep/13/2018
|-
|Earl Wood || Paul V || Sep/13/2018
|-
|Jacob Dawson || Paul V || Sep/13/2018
|-
|Farsheed Hamidi-Toosi || Paul V || Sep/27/2018
|-
|Farsheed Hamidi-Toosi || Paul V || Sep/27/2018
|-
|Tim Bielawa || Paul V || Sep/27/2018
|-
|Farsheed Hamidi-Toosi || Paul V || Sep/27/2018
|-
|Gwenn-Ael Lynn || Ralph Brendler || Oct/04/2018
|-
|Gwenn-Ael Lynn || Ralph Brendler || Oct/04/2018
|-
|Tatjana Paunesku || Ralph Brendler || Nov/29/2018
|-
|Kevin Bradley || Paul V || Dec/07/2018
|-
|Dan Gulick || Paul V || Dec/07/2018
|-
|Jim Lund || Paul Van Lake || Dec/07/2018
|-
|Deanna Musurlian || Ralph Brendler || Jan/24/2019
|-
|Pat Hillegass || Ralph Brendler || Jan/24/2019
|-
|Brian Barnt || Ralph Brendler || Feb/07/2019
|-
|Matt Dinning || Ralph Brendler || Feb/07/2019
|-
|Tony Green || Ralph Brendler || Feb/07/2019
|-
|Johanna Vargas || David Earl || Feb/13/2019
|-
|Alex Biardo || Paul Van Lake || Mar/01/2019
|-
|Tyler Moench || Ralph Brendler || Mar/03/2019
|-
|Carsten Lohan || Ralph Brendler || Mar/07/2019
|-
|Bobby Salazar || Ralph Brendler || Mar/21/2019
|-
|Vaibhav Konanur || Paul Van Lake || Mar/30/2019
|-
|Sean Blum || Ralph Brendler || Apr/04/2019
|-
|Maciej Warchalowski || Paul V || Apr/10/2019
|-
|David Earley || Ralph Brendler || Apr/18/2019
|-
|Zach Graceffa || Ralph Brendler || Apr/18/2019
|-
|David Pfeffer || Paul V || May/24/2019
|-
|Jack Gibbons || Paul V || Jun/20/2019
|-
|Tim Whelan || Ralph Brendler || Jun/27/2019
|-
|Andrew Soghigian || Ralph Brendler || Jul/11/2019
|-
|Luke Krudwig || Ralph Brendler || Jul/11/2019
|-
|Nathan Upchurch || Ralph Brendler || Jul/11/2019
|-
|Paul Ocampo || Ralph Brendler || Jul/11/2019
|-
|Eric Kostecki || Paul V || Jul/18/2019
|-
|Michael Baker || Paul V || Jul/18/2019
|-
|Sarah Lu || Ralph Brendler || Jul/25/2019
|-
|Connar Rosebraugh || Ralph Brendler || Aug/01/2019
|-
|Joseph Kardia || Ralph Brendler || Aug/01/2019
|-
|Kevin Huemann || Ralph Brendler || Aug/01/2019
|-
|Szymon Mirek || David Earl || Aug/18/2019
|-
|Justin Pestka || Ralph Brendler || Aug/30/2019
|-
|Arjun Sharma || Ralph Brendler || aug 10 2017
|-
|Mike Thompson || Michelle DeLeon || 08/22/19
|-
|Denise Allen || Paul V || 08/29/19
|-
|Sam Vuchetich || Ralph Brendler || 09/05/19
|-
|Malindima Sampa || Paul V || 10/11/19
|-
|Nikolas Gamarra || Ralph Brendler || 10/13/19
|-
|Tony Vetter || Michelle DeLeon || 10/06/19
|-
|Drew Deitch || Michelle DeLeon || 10/31/19
|-
|Adam Rangwala || Ralph Brendler || 11/14/19
|-
|Derek Smith || Ralph Brendler || 11/14/19
|-
|Jeff Becker || Eric Beauchamp || 11/23/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|Ryan Zoghlin
|Paul V
|1/14/2020
|}

[[Category:Shop Equipment]]
[[Category:Fabrication]]
[[Category:Wood Shop]]

Rockwell Delta 20" Bandsaw

2020-01-18T21:21:06Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = Pumping Station:One
|hostarea = Wood Shop
|certification = yes
|hackable = no
|model = 28-350
|serial = 1457257
|arrived = 8/26/15
|where = Wood Shop
|doesitwork = yes
|contact = matt . triano @ gmail . com
|trustee = Ralph Brendler
|value = $1,000
|move me = yes
|image = RockwellDelta20Bandsaw.jpg
}}

=== Status ===
* 3/6/2019. Andrew w replaced drive belt
* 2/23/2019 drive belt broke, status will be updated once underway/fixed.
* 10/18/2018 blade broke & Eric B. replaced it
* 5/31/2019 someone broke off one of the guides while “brushing off” the table. it is usable but blade stability is poor. NEW guide made by helpful cold metals.
*. 8/2019. Drive belt and pulley came off drive shaft. Eric and Gary replaced but drive belt does not run perfectly true. Brake does not seem to be optimally functional. Ralph will do a tune up soon.

* Tires are out of lateral alignment as well. Ralph and helpers will do a total overhaul Saturday 9/7/2019
* 9/8/2019. Ralph and Tim did total overhaul with new tires and belt. But later in day, blade was reportedly running off lower tire.

* Ralph repaired lower tire. Discovered that we cannot run at fastest pulley setting.
* 9/10 throat plate broken again
* 9/16/19 joe made new throat plate
* 10/13/19. Ralph discovered major bearing issues. Parts ordered.
* 11/2/2019. Ralph put it back into service with the great assistance of Jim brink
* 12/29/2019 thrust bearings and guides failure
* 12/31/2019 Ralph replaced thrust bearings, guides and other pats top wheel bearing/shaft still needs work, but she's usable again

* 1/8/2020 blade badly kinked. person was sawing fresh bark-on logs. i spoke with him AFTER. gn
switched to fine blade. new 1/2 inch blade on wall hanger

==Notes==
manual: [[File:Rockwell-28-350.pdf]]
related manual with more details: [[File:Rockwell20bandsaw.pdf]]

* https://ozarktoolmanuals.com/ozarkshoptalkblog/machine-idd-rockwell-delta-20-wood-band-saw-28-350/

The best manual is at http://www.walkemooretools.com/wp/wp-content/uploads/2015/07/Delta_Rockwell-bandsaw-manual.pdf

== Authorization; How to get Authorized ==

*Authorizations for the 14" Rockwell do not carry over to this tool
*This tool requires authorization for use.
*To be authorized, please see an authorized proctor/trainer from the list, below.

=== Consumable Parts ===
* This saw takes 141" blades.
* Thrust bearings type [https://www.mcmaster.com/5972k2 6203-2Z] (17mm x 40mm x 12mm). Be sure to get 2Z or ZZ (steel shield) and not 2RS (rubber shield).
* Throat plate. We still need this made frequently

Throat plate templates/model courtesy of Joe Dowling

zip of SKP, STL and f3D files : [[File:Bandsaw Plate.zip]]

image [[Media:picofbandsawplate.jpg]] and

Fusion 360 model at Joe's Adobe360 https://a360.co/2RdzuCe

There is usually a spare plates in the locked cabinet

==Tips on Use==

This section is based on a [https://groups.google.com/forum/#!msg/pumping-station-one/rCix6WMMS4Q/S6Ds9sO7DAAJ discussion that took place on the mailing list].

Band-saws have two main uses in the wood shop:

# The primary use is to make curved cuts in a piece of flat wood. In this case the piece is held by hand and guided so the blade follows the curve. A fence is counterproductive for this use.
# The second is resawing lumber that is too thick for the table saw. This is typically, but not exclusively, done with valuable pieces of wood for the purpose of creating a veneer. A fence may be appropriate for this use.

With a bandsaw, you basically never want to have the fence locked parallel to the blade. Every blade will have some degree of drift, and it is necessary to accommodate this drift to achieve a straight cut. There are two common solutions: single-point fences, and adjustable angle fences. PS:1 has both a nice magnetic adjustable fence and a single-point fence that attaches to it.

With a single point fence, you adjust for the drift angle by eye as you cut. This quick and easy method is most appropriate for resawing of narrower boards with a width of 6" or less.

For wider boards, use the adjustable fence with a tall secondary fence attached, carefully adjusted to the drift angle of the blade. For really wide boards, you can also use a presser-board to ensure contact with the fence.

Some additional advice on resawing:

* Buy a nice blade and learn how to install and adjust it. The PS:1 blades are often fairly dull and don't track well.
* Make sure your stock is prepared well, with at least one flat face and one square and flat edge.
* Try to keep only 3-10 teeth in the wood. A 1.5 tpi blade is appropriate for most resawing.
* Use a skip-tooth blade, at least 1" wide (but see note below).

{{WoodshopProctors}}

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Keon Turner
|Ron Olson
|
|-
|Hunter Koerner
|Eric Beauchamp
|
|-
|Deanna Williams
|Eric Beauchamp
|
|-
|Ray Doeksen
|Eric Beauchamp
|
|-
|Burton Kent
|Eric Beauchamp
|
|-
|Casey Olson
|Jason Shanfield
|
|-
|Tom Judge
|Matt Triano
|
|-
|Jeff Smykil
|(Pending confirmation)
|
|-
|Anna Yu
|Matt Triano
|
|-
|Jon Levine
|Jason Shanfield
|
|-
|Kyle Bieneman
|Eric Beauchamp
|
|-
|Niko Hawley
|Eric Beauchamp
|
|-
|Kevin Mitchell
|Eric Beauchamp
|
|-
|Adam Moffatt
|Jason Shanfield
|
|-
|Peter Letscher
|Eric Beauchamp
|11/05/15
|-
|Glenn Trussell
|Eric Beauchamp
|11/05/2015
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Shine Chen
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/04/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Marcin Ignasiak
|Eric Beauchamp
|
|-
|Thomas Ward
|Andy L.
|11/18/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Chris Kohl
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Peter Brask
|Eric Beauchamp
|1/14/16
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
|Shelly Loke-Gayares
|Eric Beauchamp
|1/14/16
|-
|Saul Weiner
|Eric Beauchamp
|1/14/16
|-
|Brandon Love
|Eric Beauchamp
|1/28/16
|-
|Sam Paris
|Eric Beauchamp
|1/28/16
|-
|Craig Koszewski
|Eric Beauchamp
|1/28/16
|-
|Christopher Carson
|Eric Beauchamp
|2/25/16
|-
|Jared K
|Andy L
|3/03/16
|-
|Keith Couture
|Eric Beauchamp
|3/10/16
|-
|Brian Cuocci
|Andy L
|3/17/16
|-
|Julie Zwolinski
|Eric Beauchamp
|3/24/16
|-
|Nick Puglisi
|Eric Beauchamp
|4/21/16
|-
|Andy Muhic
|Andy Larkin
|4/28/16
|-
|Colin Campbell
|Andy L
|5/5/16
|-
|Ken Burkhardt
|Andy Larkin
|5/5/16
|-
|Hans Griese
|Andy Larkin
|5/5/16
|-
|Josh Younger
|Eric Beauchamp
|5/19/16
|-
|Ian Monroe
|Eric Beauchamp
|5/19/16
|-
|An Phan
|Andy Larkin
|7/7/16
|-
|Donald Wells
|Andy Larkin
|8/4/16
|-
|Derwin Umali
|Andy Larkin
|8/7/16
|-
|[[User:mct|McTavish McArdle]]
|Andy Larkin
|2016-08-04
|-
|Joe Dowling
|Ken Burkhardt
|8/15/16
|-
|Leo Rodman
|Jason S
|9/12/16
|-
|[[user:guijemont|Guillaume Emont]]
|Ken Burkhardt
|9/19/16
|-
|Max Rashes
|Ken Burkhardt
|9/20/16
|-
|Revant Ohri
|Andy L
|9/15/16
|-
|Aaron Mintz
|Ken Burkhardt
|10/17/16
|-
|Brian Carstensen
|Ken Burkhardt
|10/17/16
|-
|Jon Komperda
|Ken Burkhardt
|10/17/16
|-
|Regan Via
|Ken Burkhardt
|10/17/16
|-
|Robert Richardson
|Ken Burkhardt
|10/17/16
|-
|Ryan Fiebing
|Ken Burkhardt
|10/24/16
|-
|Jack Berg
|Ken Burkhardt
|11/07/16
|-
|Logan Price
|Andy Larkin
|11/21/16
|-
|Kris Blouch
|Andy Larkin
|11/21/16
|-
|Tony Iacullo
|Andy
|12/5/16
|-
|Chris Ruhland
|Andy Larkin
|01/05/17
|-
|John McBride
|Andy Larkin
|01/19/17
|-
|Will Heil
|Andy Larkin
|01/19/17
|-
|Dusty Buyck
|Andy Larkin
|01/19/17
|-
|Bruce Mace
|Eric Beauchamp
|02/20/17
|-
|Matthew Quigley
|Andy Larkin
|03/02/17
|-
|W. Anthony Claypool
|Andy Larkin
|03/16/17
|-
|Crystal Morales
|Andy Larkin
|2017-03-16
|-
|Jason Pittman
|Andy Larkin
|2017-03-16
|-
|Sam Chen
|Andy Larkin
|
|-
|Abel Greenwald
|Andy Larkin
|
|-
| [[User:Andrewvaughan|Andrew Vaughan]]
| Andy Larkin
| 2017-04-25
|-
|Molly Adamski
|Ralph Brendler
|4/27/17
|-
|Shabab Mustafa
|Ralph Brendler
|4/27/17
|-
|Adomas Tautkus
|Ralph Brendler
|4/27/17
|-
|Crystal Zapata
|Ralph Brendler
|4/27/17
|-
|Alexa Viscius
|Ralph Brendler
|4/27/17
|-
|David Earl
|Ralph Brendler
|5/4/17
|-
|Paul McClay
|Ralph Brendler
|5/18/17
|-
|Jim Handley
|Ralph Brendler
|5/13/17
|-
|Luis Colmenares
|Ralph Brendler
|6/1/17
|-
|Kari Danek
|Ralph Brendler
|6/15/17
|-
|Christophe Laurent
|Ralph Brendler
|8/10/17
|-
|[[User:spektre1|Danielle MacDonald]]
|Ralph Brendler
|2017-06-29
|-
|Zack Sasnow
|Paul Van Lake
|8/3/2017
|-
|Arjun Sharma
|Ralph Brendler
|8.10.17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|Sam Dreyer
|Ralph Brendler
|8/30/17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|Joanna C.
|Sam O.
|9/27/17
|-
|Mark Haughey
|Sevin Straus
|9/30/17
|-
|Jacqueline Villa
|Maria Miller
|10/3/17
|-
|Mike Thariath
|Ralph Brendler
|10/19/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Tee
|Paul V
|11/09/17
|-
|Nick Fera
|Paul V
|11/09/17
|-
|[[User:frenchy|Jeremie Davis]]
|Ralph Brendler
|11/16/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Corey Toyama
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Jeff Hassberger
|Ralph Brendler
|
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Mac MacDevitt
|Paul V
|12/7/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Jamin Nollsch
|Ralph Brendler
|12/28/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brandler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Michael Ice
|Ralph Brendler
|2/08/18
|-
|Francisco becerril
|Ralph Brendler
|2/08/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|[[User:waynr|Wayne Warren]]
|Ralph Brendler
|3/22/18
|-
|Adam Hall
|Paul V
|3/29/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Matt Maggio
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|4/19/18
|-}
|Gary Newhouse
|Ralph Brendler
|4/19/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
| Wayne Hendryx
| Ralph Brendler
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Fritz Sullivan
| Ralph Brendler
| 5/30/18
|-
| Elizabeth Reuter
| Ralph Brendler
| 5/30/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Chris Niziolek
| Ralph Brendler
| 6/14/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Eli Schlossberg
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Bruce Levin
| Paul V
| 7/05/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Kathryn Connolly
| Paul V
| 7/19/18
|-
| Sam Lewis
| Paul V
| 7/19/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Adam Wilk
| Ralph Brendler
| 7/26/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Earl Wood
| Paul V
| 9/13/18
|-
| Jacob Dawson
| Paul V
| 9/13/18
|-
|Nick Prorok
|Ralph Brendler
|3/8/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Tim Bielawa
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
| Landon Smith
| Ralph Brendler
| 10/18/18
|-
| Will Brown
| Ralph Brendler
| 10/31/18
|-
| Tatjana Paunesku (tpaune)
| Ralph Brendler
| 11/29/18
|-
|Jim Lund
|Paul Van Lake
|12/7/18
|-
|Deanna Musurlian
|Ralph Brendler
|01/24/19
|-
|Pat Hillegass
|Ralph Brendler
|1/24/19
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Charlie Kepner
|Paul Van Lake
|03/01/19
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
|Tony Green
|Ralph Brendler
|02/07/19
|-
|Craig Cernek
|Dave Solomon
|03/27/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|Zach Graceffa
| Ralph Brendler
|4/18/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|David Pfeffer
|Paul V
|05/24/19
|-
|Jack Gibbons
|Paul V
|06/20/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Patrick Cook
|Ralph Brendler
|07/11/19
|-
|Matt Saunders
|Ralph Brendler
|07/11/19
|-
|Nathan Upchurch
|Ralph Brendler
|07/11/19
|-
|Luke Krudwig
|Ralph Brendler
|07/11/19
|-
|Andrew Soghigian
|Ralph Brendler
|07/11/19
|-
|Eric Kostecki
|Paul V
|07/18/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Sarah Lu
|Ralph Brendler
|07/25/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Connar Rosebraugh
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Hara Kumaran
|David Earl
|08/18/19
|-
|Miles Hosanna
|Ralph Brendler
|09/19/2019
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|Tony Vetter
|Michelle DeLeon
|10/06/19
|-
|Adam Rangwala
|Ralph Brendler
|11/14/19
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Adam Keim
|Ralph Brendler
|11/14/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|Ryan Zoghlin
|Paul V
|1/14/2020
[[Category:Wood Shop]]
[[Category:Shop Equipment]]

Laguna 16" Planer

2020-01-18T21:17:47Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = no
|model = MPLAN1510-0120
|serial = 144367
|arrived =
|doesitwork = yes
|contact =
|where = Wood Shop
|value = $3000
|image = LagunaPlaner.jpg
|hostarea = Wood Shop
}}
== reference material ==
[[file:Laguna16PlanerManual.pdf]]
== Guidelines for proper use ==
# '''Always''' check your wood for nails or staples. Something as small as the staple at the end of a 1x1 can ruin the blades. If you're not sure, check the entire piece with the metal detector sitting on the table saw.
# '''Always''' measure the thickness of your work and set the initial and working blade height to remove only small amounts of material per pass. You will damage the blades if you manage to dig the machine out on your work.
# If the machine is making a strange noise when you use it, there is a problem, and you should '''ask for help.'''
# If the blades are dull or damaged, '''contact the area host immediately.'''
# If you break something, or damage the tool, '''contact the area host immediately.''' Don't let others do more damage or hurt themselves by using a broken tool.
# '''Always''' make sure that the dust collection bag isn't too full and is passing air freely.
# '''Always''' vacuum the machine, cutting area, and the table around the machine when you are done.

April 29 2019. Planer shut down in mid use. Broken elec connection repaired but sill does not start. See gg and slack for more detail.
'''This tool requires authorization for use.'''

== Checklist ==
PS1 is experimenting with the use of [[checklists]] to encourage the safe use and proper care of tools in the workspace. The latest version of the checklist for this tool is stored as a [https://docs.google.com/document/d/1C0pna59ZDq92vC2uEZM5ANUGh6qx-svit9atMhJNLm8/edit?usp=sharing Google Doc] that can be edited by anyone. If you make changes, update the effective date at the bottom of the document. Print a new copy, and replace the old one.

== External Links ==
*[https://lagunatools.com/classic-machinery/planers/planer-16-inch-4-post/ Manufacturer Page]
*[https://system.na3.netsuite.com/core/media/media.nl?id=661707&c=860860&h=94f90373845230ed877d&_xt=.pdf Owner's Manual]
maintenance gdoc click on "1" to view, "link icon" to edit [https://docs.google.com/spreadsheets/d/e/2PACX-1vRiwd8cogJ6NOWSUqhAaSJM_vcQi1nAUZ-dqsxR4iuGnFKr1g8X5w7qmZNjkeD3xK_f9pwu1Vnu09wm/pubhtml]
* [https://docs.google.com/spreadsheets/d/e/2PACX-1vRiwd8cogJ6NOWSUqhAaSJM_vcQi1nAUZ-dqsxR4iuGnFKr1g8X5w7qmZNjkeD3xK_f9pwu1Vnu09wm/pubhtml Internal PS1 Maintenance Google Doc]

{{WoodshopProctors}}

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Matt Triano
|Danger committee
|
|-
|Eric Beauchamp
|Danger committee
|
|-
|Jason Shanfield
|Matt Triano
|
|-
|Tom Judge
|Matt Triano
|
|-
|Hunter Koerner
|Eric Beauchamp
|
|-
|Deanna Williams
|Eric Beauchamp
|
|-
|Casey Olson
|Eric Beauchamp
|
|-
|Burton Kent
|Eric Beauchamp
|
|-
|Jeff Smykil
|Matt Triano
|
|-
|Ray Doeksen
|Jason Shanfield
|
|-
|Anna Yu
|Jason Shanfield
|
|-
|Todd Allen
|Ron Olson
|
|-
|Jon Levine
|Jason Shanfield
|
|-
|Kyle Bieneman
|Eric Beauchamp
|
|-
|Niko Hawley
|Eric Beauchamp
|
|-
|-
|Adam Moffatt
|Eric Beauchamp
|
|-
|Marcin Ignasiak
|Eric Beauchamp
|
|-
|Keon Turner
|Ron Olson
|
|-
|Mike Mandrea
|Eric Beauchamp
|
|-
|Caleb Young
|Eric Beauchamp
|
|-
|Erik Wessing
|Eric Beauchamp
|
|-
|Doorman Dave
|Eric Beauchamp
|
|-
|Peter Letscher
|Eric Beauchamp
|11/05/15
|-
|Glenn Trussell
|Eric Beauchamp
|11/05/2015
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Shine Chen
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/03/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kevin Schwartzenberg
|Eric Beauchamp
|12/03/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Chris Kohl
|Eric Beauchamp
|1/8/2016
|-
|Szymon Sambor
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Peter Brask
|Eric Beauchamp
|1/14/16
|-
|Andrew Dalesandro
|Eric Beauchamp
|1/14/16
|-
|Shelly Loke-Gayares
|Eric Beauchamp
|1/14/16
|-
|Saul Weiner
|Eric Beauchamp
|1/14/16
|-
|Brandon Love
|Eric Beauchamp
|1/28/16
|-
|Christopher Carson
|Eric Beauchamp
|2/25/16
|-
|Jared K
|Andy L
|3/03/16
|-
|Keith Couture
|Eric Beauchamp
|3/10/16
|-
|Julie Zwolinski
|Eric Beauchamp
|3/24/16
|-
|Nick Puglisi
|Eric Beauchamp
|4/21/16
|-
|Andy Muhic
|Andy Larkin
|4/28/16
|-
|Greg "Nerobro" Teiber
|Dan Locks
|4/29/16
|-
|Ken Burkhardt
|Andy Larkin
|5/5/16
|-
|Hans Griese
|Andy Larkin
|5/5/16
|-
|Spencer Simms
|Eric Beauchamp
|05/19/2016
|-
|Josh Younger
|Eric Beauchamp
|5/19/16
|-
|Ian Monroe
|Eric Beauchamp
|5/19/16
|-
|Joseph Juhnke
|Eric Beauchamp
|6/20/16
|-
|An Phan
|Andy Larkin
|07/07/16
|-
|Jim Brink
|Andy Larkin
|07/21/16
|-
|Donald Wells
|Andy Larkin
|8/4/16
|-
|Derwin Umali
|Andy Larkin
|8/7/16
|-
|[[User:mct|McTavish McArdle]]
|Andy Larkin
|2016-08-04
|-
|Joe Dowling
|Ken Burkhardt
|8/15/16
|-
|Leo Rodman
|Jason S
|9/12/16
|-
|Brian Cuocci
|Andy L
|9/15/16
|-
|Revant Ohri
|Andy L
|9/15/16
|-
|Max Rashes
|Ken Burkhardt
|9/20/16
|-
|Aaron Mintz
|Ken Burkhardt
|10/17/16
|-
|Brian Carstensen
|Ken Burkhardt
|10/17/16
|-
|Jon Komperda
|Ken Burkhardt
|10/17/16
|-
|Regan Via
|Ken Burkhardt
|10/17/16
|-
|Robert Richardson
|Ken Burkhardt
|10/17/16
|-
|Jack Berg
|Ken Burkhardt
|11/07/16
|-
|Logan Price
|Andy Larkin
|11/21/16
|-
|Kris Blouch
|Andy Larkin
|11/21/16
|-
|Tony Iacullo
|Andy
|12/5/16
|-
|Ashish Jasani
|Andy Larkin
|11/28/16
|-
|Chris Ruhland
|Andy Larkin
|01/05/17
|-
|John McBride
|Andy Larkin
|01/19/17
|-
|Will Heil
|Andy Larkin
|01/19/17
|-
|Dusty Buyck
|Andy Larkin
|01/19/17
|-
|Matthew Quigley
|Andy Larkin
|03/02/17
|-
|W. Anthony Claypool
|Andy Larkin
|03/16/17
|-
|-
|Crystal Morales
|Andy Larkin
|2017-03-16
|-
|Jason Pittman
|Andy Larkin
|2017-03-16
|-
|Ashley Borg
|Andy Larkin
|4/13/17
|-
|Sam Chen
|Andy Larkin
|
|-
| [[User:Andrewvaughan|Andrew Vaughan]]
| Andy Larkin
| 2017-04-25
|-
|Molly Adamski
|Ralph Brendler
|4/27/17
|-
|Shabab Mustafa
|Ralph Brendler
|4/27/17
|-
|Adomas Tautkus
|Ralph Brendler
|4/27/17
|-
|Crystal Zapata
|Ralph Brendler
|4/27/17
|-
|Alexa Viscius
|Ralph Brendler
|4/27/17
|-
|David Earl
|Ralph Brendler
|5/4/17
|-
|Luis Colmenares
|Ralph Brendler
|6/1/17
|-
|Kari Danek
|Ralph Brendler
|6/15/17
|-
|Christophe Laurent
|Ralph Brendler
|8/10/17
|-
|[[User:spektre1|Danielle MacDonald]]
|Ralph Brendler
|2017-06-29
|-
|Zack Sasnow
|Paul Van Lake
|8/3/17
|-
|Arjun Sharma
|Ralph Brendler
|8.10.17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|Sam Dreyer
|Ralph Brendler
|8/30/17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|Mark Haughey
|Sevin Straus
|9/30/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
| Tommy TBones Cramer
|Ralph Brendlet
|08/30/17
|-
|Mike Thariath
|Ralph Brendlet
|10/19/17
|-
|Chinbayar Davaatseren
|Ralph Brendler
|11/02/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Tee
|Paul V
|11/09/17
|--
|[[User:frenchy|Jeremie Davis]]
|Ralph Brendler
|11/16/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Jeff Hassberger
|Ralph Brendler
|11/2/17
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Mac MacDevitt
|Paul V
|12/7/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Jamin Nollsch
|Ralph Brendler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brandler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Scott Fullman
|Ralph Brendler
|2/8/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Nick Prorok
|Ralph Brendler
|3/8/18
|-
|Ricardo Staudt
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|[[User:waynr|Wayne Warren]]
|Ralph Brendler
|3/22/18
|-
|Adam Hall
|Paul V
|3/29/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Matt Maggio
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|4/19/18
|-}
|Gary Newhouse
|Ralph Brendler
|4/26/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
|John Burkholder
|Ralph Brendler
|5/03/18
|-
| Wayne Hendryx
| Ralph Brendler
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Eli Schlossberg
| Ralph Brendler
| 6/14/18
|-
| Tyler Works
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Bruce Levin
| Paul V
| 7/05/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Kathryn Connolly
| Paul V
| 7/19/18
|-
| Sam Lewis
| Paul V
| 7/19/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Adam Wilk
| Ralph Brendler
| 7/26/18
|-
|Tom Henderson
|Ralph Brendler
|2018-08-09
|-
| Kelvin Lane
| Paul V
| 9/13/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Earl Wood
| Paul V
| 9/13/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
| Will Brown
| Ralph Brendler
| 10/31/18
|-
| Tatjana Paunesku (tpaune)
| Ralph Brendler
| 11/29/18
|-
|Jim Lund
|Paul Van Lake
|12/6/18
|-
|Pat Hillegass
|Ralph Brendler
|1/24/19
|-
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
|Tony Green
|Ralph Brendler
|02/07/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|David Pfeffer
|Paul V
|05/24/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Nathan Upchurch
|Ralph Brendler
|07/11/19
|-
|Andrew Soghigian
|Ralph Brendler
|07/11/19
|-
|Luke Krudwig
|Ralph Brendler
|07/11/19
|-
|Paul Ocampo
|Ralph Brendler
|07/11/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Sarah Lu
|Ralph Brendler
|07/25/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Connar Rosebraugh
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Hara Kumaran
|David Earl
|08/18/19
|-
|Steven Rummelhoff
|Ralph Brendler
|08/22/19
|-
|-
|Mike Thompson
|Michelle DeLeon
|08/22/19
|-
|Denise Allen
|Paul V
|08/29/19
|-
|Sam Vuchetich
|Ralph Brendler
|09/05/19
|-
|Nikolas Gamarra
|Ralph Brendler
|10/13/19
|-
|Adam Rangwala
|Ralph Brendler
|11/14/19
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Guillermo Tinoco
|David Earl
|12/05/19
|-
|paulina hubli
|david earl
|12/5/2019
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|Ryan Zoghlin
|Paul V
|1/14/2020
|}
[[Category:Wood Shop]]
[[Category:Shop Equipment]]

Ridgid Oscillating Spindle Sander

2020-01-18T21:14:24Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner = PS:One
|certification=yes
|hackable = NO
|model = G0654
|serial = NA
|arrived = December 2014
|doesitwork = yes
|contact = Matt Triano
|where = Wood Shop
|hostarea = Wood Shop
|value = $200.00
|image = ridgidossander.jpg
}}

please see: https://wiki.pumpingstationone.org/Sander_(oscillating_spindle)_-_Steel_City
it is the current spindle sander since mid 2018. However it no longer oscillates so this backup returns to service.

'''This tool requires authorization for use.

12/26/2019 replaced spindle knob . THIS IS A LEFT HAND THREADED KNOB AND SEEMS TO CONFUSE MANY USERS '''

The belt sander attachment lives in a pocket at the back of the tool.

{{WoodshopProctors}}

== Rules ==
# Always check your wood for nails or staples. If you're not sure, check the entire piece with the metal detector or a magnet.
# Always use dust collection.
# Always use the appropriate washer with the oscillating drums, and put the washers away when you're done.
# Adjust the belt sander so that the belt tracks without running against the metal supports.
# Always replace washers and throat plates in their respective slots on the front of the machine when you switch accessories.

== Documentation ==
* [https://www.ridgid.com/us/en/oscillating-edge-belt-spindle-sander Links to manual and parts list]

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Matt Triano
|Matt Triano
|
|-
|Erin Kunkel
|Matt Triano
|
|-
|Tyler Matthew
|Matt Triano
|
|-
|Shae Kurko
|Matt Triano
|
|-
|Ben Bogler
|Matt Triano
|
|-
|Sam Paris
|Ron Olson
|
|-
|Knute Martell
|Ron Olson
|
|-
|Chris Kleehammer
|[[User:jason|Jason Shanfield]]
|
|-
|Trey Elliott
|[[User:jason|Jason Shanfield]]
|
|-
|Nik Brink
|[[User:jason|Jason Shanfield]]
|
|-
|Frances Ritchie
|Ron Olson
|
|-
|Ben Kern
|Ron Olson
|
|-
|Eric Yu
|Ron Olson
|
|-
|Karol Slowikowski
|Ron Olson
|
|-
|Chris Smith
|Ron Olson
|
|-
|Ryan Pierce
|Matt Triano
|
|-
|Benjamin Miller
|Ron Olson
|
|-
|Jennie P
|Ron Olson
|
|-
|Eugene Liokumovich
|Ron Olson
|
|-
|Tomas Ward
|Ron Olson
|4/26/2015
|-
|Les Schier
|Jason Shanfield
|5/2/15
|-
|Hunter Koerner
|Eric Beauchamp
|6/4/15
|-
|Erik Wessing
|Eric Beauchamp
|
|-
|Kurt Ziegel
|Eric Beauchamp
|6/4/15
|-
|Simon Pyle
|Eric Beauchamp
|6/4/15
|-
|Anthony Phelps
|Eric Beauchamp
|8/27/2015
|-
|Ralph Brendler
|Eric Beauchamp
|8/27/2015
|-
|Kyle Bieneman
|Eric Beauchamp
|8/27/2015
|-
|Jim Baker
|Eric Beauchamp
|8/27/2015
|-
|Shane Kanter
|Ron Olson
|9/12/2015
|-
|Marcin Ignasiak
|Eric Beauchamp
|
|-
|Deanna Williams
|Eric Beauchamp
|
|-
|Niko Hawley
|Eric Beauchamp
|
|-
|Kevin Mitchell
|Eric Beauchamp
|
|-
|[[User:themoffatt|Adam Moffatt]]
|Eric Beauchamp
|10/22/2015
|-
|Mike Mandrea
|Eric Beauchamp
|11/5/2015
|-
|Caleb Young
|Eric Beauchamp
|
|-
|Aaron Carlock
|Eric Beauchamp
|11/19/2015
|-
|Patrick Lynch
|Eric Beauchamp
|11/19/2015
|-
|Mike Forkan
|Eric Beauchamp
|11/19/2015
|-
|Ethan Sanders
|Eric Beauchamp
|11/19/2015
|-
|Alex Al-Hamdan
|Eric Beauchamp
|12/03/2015
|-
|Alvaro Caceres
|Eric Beauchamp
|12/03/2015
|-
|Kelly Steensma
|Eric Beauchamp
|11/19/2015
|-
|Dan (Mike) Arwine
|Eric Beauchamp
|11/19/2015
|-
|Connor Sullivan
|Eric Beauchamp
|1/8/2016
|-
|Erik Funkhouser
|Ron Olson
|11/01/2015
|-
|Shelly Loke-Gayares
|Eric Beauchamp
|1/14/16
|-
|Saul Weiner
|Eric Beauchamp
|1/14/16
|-
|Brandon Love
|Eric Beauchamp
|1/28/16
|-
|Christopher Carson
|Eric Beauchamp
|2/25/16
|-
|Jared K
|Andy L
|3/03/16
|-
|Nick Puglisi
|Eric Beauchamp
|4/21/16
|-
|Andy Muhic
|Andy Larkin
|4/28/16
|-
|Josh Younger
|Eric Beauchamp
|5/19/16
|-
|Joseph Juhnke
|Eric Beauchamp
|6/20/16
|-
|Donald Wells
|Andy Larkin
|8/4/16
|-
|[[User:mct|McTavish McArdle]]
|Andy Larkin
|2016-08-04
|-
|Joe Dowling
|Ken Burkhardt
|8/15/16
|-
|Leo Rodman
|Jason S
|9/12/16
|-
|Brian Cuocci
|Andy L
|9/15/16
|-
|Regan Via
|Ken Burkhardt
|10/17/16
|-
|Jon Komperda
|Ken Burkhardt
|10/17/16
|-
|Logan Price
|Andy Larkin
|11/21/16
|-
|Kris Blouch
|Andy Larkin
|11/21/16
|-
|Chris Ruhland
|Andy Larkin
|01/05/17
|-
|Bruce Mace
|Eric Beauchamp
|02/20/17
|-
|Matthew Quigley
|Andy Larkin
|03/02/17
|-
|Kari Danek
|Ralph Brendler
|6/15/17
|-
|Christophe Laurent
|Ralph Brendler
|8/10/17
|-
|[[User:spektre1|Danielle MacDonald]]
|Ralph Brendler
|2017-06-29
|-
|Sam Yi
|Ralph Brendler
|7/27/17
|-
|Zack Sasnow
|Paul Van Lake
|8/3/2017
|-
|Arjun Sharma
|Ralph Brendler
|8.10.17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
|Mike Thariath
|Ralph Brendler
|10/19/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Corey TOyama
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Aaron Vander Bee
|Ralph Brandler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Rolf Scheidt
|Ralph Brendler
|2/22/18
|-
|Charles Barker
|Ralph Brendler
|3/8/18
|-}
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Bruce Mace
|Ralph Brendler
|3/8/18
|-
|Gary Newhouse
|Eric Beauchamp
|4/26/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
|John Burkholder
|Ralph Brendler
|5/03/18
|-
| Wayne Hendryx
| Ralph Brendler
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Mike Yacobucci
| Ralph Brendler
| 7/12/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
|Maciej Warchalowski
|Paul V
|04/10/19
|-
|David Pfeffer
|Paul V
|05/24/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Ryan Zoghlin
|Paul V
|1/14/2020
|}
[[Category:Shop Equipment]]
[[Category:Wood Shop]]

Drill Press Craftsman 20in woodshop

2020-01-18T21:09:35Z

Rfoto: /* List of Currently Authorized Users */

{{Template:EquipmentPage
|owner= PS:One
|model=
|serial=
|arrived=
|doesitwork=yes
|contact=[[user: ericbeau|Eric Beauchamp]]
|where=Wood Shop
|certification=yes
|hackable=no
|value=$500
|image=Craftsman20Drill.jpg
|hostarea=Wood Shop
}}

The Craftsman 20" drill press is the primary drill press in the wood shop. Authorization is included in the general wood shop authorization. For upcoming authorizations, see the [https://pumpingstationone.org/events/ calendar].

== Safety ==
The [[:file:Craftsman20_drill_manual.pdf|user manual is available here]].

==Maintenance==
Per the [[:file:Craftsman20 drill manual.pdf|user manual]], the drill should be periodically cleaned of dust, the table wiped with wax to prevent rust, and (if needed) the quill lubricated with a dry lubricant like silicone or graphite. Users should perform this maintenance as the drill is used, and PS1 should inspect the drill monthly.

===Maintenance history===

* '''July 10, 2017.''' Drill press motor is not fully connected. Belt may be rubbing on the housing.
* '''July 14, 2017.''' One of the two posts that adjusts the motor position is missing its nut. Also, there is a rack-and-pinion lever that moves the motor in and out, and one of the posts had skipped a tooth. I worked it back into position, and I believe it is now safe to use, despite the missing nut. Replacing the nut will require removing the motor, which is a two-person job.
* '''July 18, 2017.''' This is fixed now. For the record, the missing nut was M12-1.75. I put some "purple" locktite on both nuts, so hopefully we won't have to take it apart again.

== List of Currently Authorized Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|Eric Beauchamp
|Danger committee
|
|-
| [[User:andrewvaughan|Andrew Vaughan]]
| Andy Larkin
| April 26, 2017
|-
|Paul McClay
|Ralph Brendler
|5/18/17
|-
|Jim Handley
|Ralph Brendler
|5/13/17
|-
|[[User:spektre1|Danielle MacDonald]]
|Ralph Brendler
|2017-06-29
|-
|Christophe Laurent
|Ralph Brendler
|8/10/17
|-
|Sam Yi
|Ralph Brendler
|7/27/17
|-
|Zack Sasnow
|Paul Van Lake
|8/3/17
|-
|Arjun Sharma
|Ralph Brendler
|8.10.17
|-
|Justin Pestka
|Ralph Brendler
|8.30.17
|-
|Sam Dreyer
|Ralph Brendler
|8/30/17
|-
|[[User:Ekaj|Jacob Snyder]]
|Ralph Brendler
|9/7/17
|-
|James Beck
|Ralph Brendler
|9/13/17
|-
|James Marco
|Ralph Brendler
|10/5/17
|-
|[[User:bnuttin|Benjamin Nuttin]]
|Ralph Brendler
|11/02/17
|-
|Karl Healy
|Ralph Brendler
|11/2/17
|-
|Tee
|Paul V
|11/09/17
|--
|-
|Nick Fera
|Paul V
|11/09/17
|--
|[[User:frenchy|Jeremie Davis]]
|Ralph Brendler
|11/16/17
|-
|[[User:wittnl|Nathan Witt]]
|Ralph Brendler
|11/30/2017
|-
|Theo T
|Ralph Brendler
|11/30/2017
|-
|Wally Ibrahim
|Ralph Brendler
|11/30/17
|-
|Jeff Hassberger
|Ralph Brendler
|
|-
|Mac MacDevitt
|Paul V
|12/7/17
|-
|Ben Starett
|Ralph Brendler
|12/14/17
|-
|-
|Ross Hanchett
|Ralph Brendler
|12/14/17
|-
|Michael Donovan
|Ralph Brendler
|12/14/17
|-
|[[User:atomala|Alex Tomala]]
|Ralph Brendler
|12/21/17
|-
|Jamin Nollsch
|Ralph Brendler
|12/28/17
|-
|Chris Versteeg
|Ralph Brandler
|12/28/17
|-
|Aaron Vander Bee
|Ralph Brendler
|1/11/18
|-
|Ben Farmer
|Ralph Brendler
|1/11/18
|-
|Joseph Crouch
|Ralph Brendler
|1/11/18
|-
|Bradford Smith
|Ralph Brendler
|1/11/18
|-
|Stephanie Pelzer
|Ralph Brendler
|1/11/18
|-
|Amanda Assaley
|Ralph Brendler
|1/11/18
|-
|Chris Eppig
|Ralph Brendler
|1/11/18
|-
|Patrick Smith
|Ralph Brendler
|1/11/18
|-
|Jeff Gershune
|Paul VanLake
|1/16/18
|-
|Bryan Pennington
|Ralph Brendler
|1/25/18
|-
|Scott Fullman
|Ralph Brendler
|2/8/18
|-
|Brandon Kennedy
|Ralph Brendler
|2/22/18
|-
|Charles Barker
|Ralph Brendler
|3/8/18
|-
|Dan Mach
|Ralph Brendler
|3/8/18
|-
|Nick Prorok
|Ralph Brendler
|3/8/18
|-
|Paul Graham
|Ralph Brendler
|3/22/18
|-
|Mike Gucciard
|Ralph Brendler
|3/22/18
|-
|Wayne Warren
|Ralph Brendler
|3/22/18
|-
|Adam Hall
|Paul V
|3/29/18
|-
|Bill Schroeder
|Ralph Brendler
|4/5/18
|-
|Mike Wilkin
|Ralph Brendler
|4/19/18
|-
|Alex Lanigan
|Ralph Brendler
|4/19/18
|-
|Jessica Jokhi
|Ralph Brendler
|4/19/18
|-
|Matt Maggio
|Ralph Brendler
|4/19/18
|-
|Jonathan Frink
|Ralph Brendler
|4/19/18
|-}
|Gary Newhouse
|Ralph Brendler
|4/26/18
|-}
|Dave DesRoberts
|Paul Van Lake
|4/26/18
|-
|Jennifer DesRoberts
|Paul Van Lake
|4/26/18
|-
|John Burkholder
|Ralph Brendler
|5/03/18
|-
| Wayne Hendryx
| Chris Iacullo
| 4/19/18
|-
|[[User:brendanf|Brendan Fortune]]
|Ralph Brendler
|5/17/18
|-
| Kirsten Landmark Masih
| Ralph Brendler
| 6/07/18
|-
| Chris Niziolek
| Ralph Brendler
| 6/14/18
|-
| Sam Wallinga
| Ralph Brendler
| 6/14/18
|-
| Bob Fritz
| Ralph Brendler
| 6/14/18
|-
| Nate Myren
| Ralph Brendler
| 6/14/18
|-
| Eli Schlossberg
| Ralph Brendler
| 6/14/18
|-
| Daniel Willmott
| Paul V
| 6/21/18
|-
| Bruce Levin
| Paul V
| 7/05/18
|-
| Joe Day
| Paul V
| 7/05/18
|-
| Kathryn Connolly
| Paul V
| 7/19/18
|-
| Sam Lewis
| Paul V
| 7/19/18
|-
| Aaron Hale
| Ralph Brendler
| 7/26/18
|-
| Geoff Klein
| Paul V
| 9/13/18
|-
| Earl Wood
| Paul V
| 9/13/18
|-
| Jacob Dawson
| Paul V
| 9/13/18
|-
| Ryan Treacy
| Paul V
| 9/20/18
|-
| Farsheed Hamidi-Toosi
| Paul V
| 9/27/18
|-
| Tim Bielawa
| Paul V
| 9/27/18
|-
| Will Holland
| Ralph Brendler
| 10/4/18
|-
| Gwenn-Ael Lynn
| Ralph Brendler
| 10/4/18
|-
| Landon Smith
| Ralph Brendler
| 10/18/18
|-
| Will Brown
| Ralph Brendler
| 10/31/18
|-
|Deanna Musurlian
|Ralph Brendler
|01/24/19
|-
|Brian Barnt
|Ralph Brendler
|02/07/19
|-
|Matt Dinning
|Ralph Brendler
|02/07/19
|-
|Alex Biardo
|Paul Van Lake
|03/01/19
|-
|Tyler Moench
|Ralph Brendler
|03/03/19
|-
|Tony Green
|Ralph Brendler
|02/07/19
|-
|Sean Blum
|Ralph Brendler
|04/04/19
|-
|Zach Graceffa
|Ralph Brendler
|04/18/19
|-
|Chris Martin
|Ralph Brendler
|05/02/19
|-
|David Pfeffer
|Paul V
|05/24/19
|-
|Tim Whelan
|Ralph Brendler
|06/27/19
|-
|Michael Baker
|Paul V
|07/18/19
|-
|Sarah Lu
|Ralph Brendler
|07/25/19
|-
|Joseph Kardia
|Ralph Brendler
|08/01/19
|-
|Kevin Huemann
|Ralph Brendler
|08/01/19
|-
|Szymon Mirek
|David Earl
|08/18/19
|-
|Hara Kumaran
|David Earl
|08/18/19
|-
|Mike Thompson
|Michelle DeLeon
|08/22/19
|-
|Denise Allen
|Paul V
|08/29/19
|-
|Sam Vuchetich
|Ralph Brendler
|09/05/19
|-
|Miles Hosanna
|Ralph Brendler
|09/19/2019
|-
|Malindima Sampa
|Paul V
|10/11/2019
|-
|Adam Rangwala
|Ralph Brendler
|11/14/2019
|-
|Derek Smith
|Ralph Brendler
|11/14/19
|-
|Austin Webster
|Michelle DeLeon
|12/10/19
|-
|Debbie Walker
|Michelle DeLeon
|12/10/19
|-
|Ryan Zoghlin
|Paul V
|1/14/2020
|}
[[Category:Shop Equipment]]
[[Category:Wood Shop]]