PS:1 Wiki Dev - User contributions [en]

Sewing Pattern Projector

2025-12-23T20:39:10Z

Ugrosse: remote and owner changes

{{Template:EquipmentPage
|owner = "Uwe Grosse"
|hostarea = Arts
|certification = no
|hackable = no
|model =
|serial =
|arrived =
|where = Arts Ceiling
|doesitwork = yes
|contact = Arts Area Host
|value = a lot
|image =

}}
=== General Notes ===
'''Do not touch the projector. Only touch the remote'''

The remote to turn the projector is hanging on a tether from the ceiling. Pull it towards you to use, then retract. Be gentle.

=== Setting up the projector ===
- Power on projector (again using remote)

- The paper roll below the table can be used for calibrating the projector. it also helps with menu navigation.

- Once projector is powered on, go to the 'wireless' section and hit 'okay' on the remote. Then choose the device type. I have not been able to setup the arts computer with the projector. using your own device is recommended.

- Once the projector is casting to the appropriate device (follow on screen(on table?) instructions, navigate to [http://Patternprojector.com patternprojector.com] on your device.

- Hit the 'calibrate' button. A grid will appear with measurements. move the corners out to match the grid on the paper roll. Once the gridlines on the projector line up exactly with the grid on the paper.

- Once calibrated, you can choose a file to project. PDFs have worked best for me. you can roll up the paper below the table before cutting fabric

=== Projecting Patterns ===
patternprojector.com is used for calibrating sizes and displaying patterns. The projector is connected to Wifi, and can be used as a cast device (airplay on apple devices) when connected to the "PumpingStationOne" Wifi network.

The pattern projector can be used to project patterns roughly 20" by 30". This is somewhat dependent on your devices resolution/ aspect ratio.. Laptops at 1920x1080 or equivalent ratio can use the most amount of room, while ipads and similar devices with slightly wider ratios would project lower. The 20" x 30" above is what can comfortably fit on the projector area from an ipad.

[[Category:Arts]] [[Category:Textiles]]

Juki 9000C

2025-12-11T04:49:40Z

Ugrosse:

{{Template:EquipmentPage
|owner = Uwe Grosse
|hostarea = Arts
|certification = yes
|hackable = no
|model = Juki DDL 9000C SMS
|serial =
|arrived = November 2025
|where = Arts Sewing Wall
|doesitwork = yes
|contact = Uwe Grosse
|value =
|image = Juki9000C.png
}}

The Juki DDL9000C SMS is a full function straight stich machine, suitable for sewing garments, tote bags, etc.



Manual:[[:File:DDL9000CSeries manual.pdf|Juki DDL9000C Manual]]

Juki 9000C

2025-12-11T00:52:05Z

Ugrosse: Creation of page

[[:File:CB3200Manual.pdf|CowBoy CB3200 Manual]]{{Template:EquipmentPage
|owner = Uwe Grosse
|hostarea = Arts
|certification = yes
|hackable = no
|model = Juki 9000C SMS
|serial =
|arrived = November 2025
|where = Arts Sewing Wall
|doesitwork = yes
|contact = Uwe Grosse
|value =
|image = Juki9000C.png
}}

The Juki DDL9000C SMS is a full function straight stich machine, suitable for sewing garments, tote bags, etc.



Full Manual:[[:File:DDL9000CSeries manual.pdf|Juki DDL9000C Manual]]

File:DDL9000CSeries manual.pdf

2025-12-11T00:48:12Z

Ugrosse: Juki DDL 9000C Manual

== Summary ==
Juki DDL 9000C Manual

Category:Arts

2025-11-04T23:35:22Z

Ugrosse: Typo

{{Infobox HostedArea
| image = Equipment-no-photo.jpg
| areaname = Arts - Graphic Arts and Textiles
| hostedsince =
| location = Second Floor
| toolcategory =
| hostname = Lydia Miller
| hostphone =
| hostemail =art@pumpingstationone.org
| hostother = @arts on Slack
| hosthours =
| hostcerts =
}}

== Rules ==

Please put supplies and tools back when you are done. Fabric cutting scissors are for use on cloth fabric and thread only. Members are welcome to use all donated materials such as beads, fabric, thread, and yarn in the space.

== Safety ==

== Tools Available ==
* [[Singer 20U Industrial Sewing Machine]]
* [[Sears Kenmore Model 158.18130 Sewing Machine]]
* [[J.C.Penney Free Arm Sewing Machine]]
* [[Singer Serger 14T948DS|Singer cutting serger [interlock] machine]]
* [[CowBoy CB3200 Leather Stitcher|CowBoy CB3200 Heavy Duty Leather Stitcher]] (w/ Flatbed Attachment)
* [[Adler Patcher|Adler 30-1]] Shoe Patcher Sewing Machine (Shoe Patcher, Repair Work)
* Juki DDL-5550N straight stitch industrial sewing machine
* Juki MO-3616 Serger
* Juki DDL 9000C SMS straight stitch industrial sewing machine
* [[Juki-LS-341-Cylinder-Arm-Sewing-Machine|Juki LS-341 Cylinder Arm Sewing Machine]] (w/ Flatbed attachment)
* Steam iron and ironing board, small [sleeve] ironing board, tailor's ham, ham holder
* [[Gravity Iron]]
* Large 8' fabric table
* Small table-top weaving loom, inkle frame loom, warping board, and assorted wooden yarn winders, hand crank yarn winder
* Knitting and crochet needles, Knifty Knitter plastic hoop style knitting looms
* Cricut paper cutter
* Large printmaking drying rack and lighted bench
* Airbrush tools and compressor
* Guillotine paper cutter
* A-Frame wooden easel; small aluminum table top easel
* Silkscreens and squeegees; t-shirt printing machine
* Leather tooling hand tools
* Ball peen hammer
* Hot glue gun
* Staple guns
* Small lamination machine
* 3-Hole punch
* Cutting mat and Xacto knife

== Wish List ==

== Certifications ==

[[Category:Hosted Areas]]
[[Category:Member Manual]]
[[Category:Equipment]]
[[Category:Projects]]
[[Category:Tutorials]]

Category:Arts

2025-11-04T23:34:07Z

Ugrosse: /* Tools Available */

{{Infobox HostedArea
| image = Equipment-no-photo.jpg
| areaname = Arts - Graphic Arts and Textiles
| hostedsince =
| location = Second Floor
| toolcategory =
| hostname = Lydia Miller
| hostphone =
| hostemail =art@pumpingstationone.org
| hostother = @arts on Slack
| hosthours =
| hostcerts =
}}

== Rules ==

Please put supplies and tools back when you are done. Fabric cutting scissors are for use on cloth fabric and thread only. Members are welcome to use all donated materials such as beads, fabric, thread, and yarn in the space.

== Safety ==

== Tools Available ==
* [[Singer 20U Industrial Sewing Machine]]
* [[Sears Kenmore Model 158.18130 Sewing Machine]]
* [[J.C.Penney Free Arm Sewing Machine]]
* [[Singer Serger 14T948DS|Singer cutting serger [interlock] machine]]
* [[CowBoy CB3200 Leather Stitcher|CowBoy CB3200 Heavy Duty Leather Stitcher]] (w/ Flatbed Attachment)
* [[Adler Patcher|Adler 30-1]] Shoe Patcher Sewing Machine (Shoe Patcher, Repair Work)
* Juki DDL-55550N straight stitch industrial sewing machine
* Juki MO-3616 Serger
* Juki DDL 9000C SMS straight stitch industrial sewing machine
* [[Juki-LS-341-Cylinder-Arm-Sewing-Machine|Juki LS-341 Cylinder Arm Sewing Machine]] (w/ Flatbed attachment)
* Steam iron and ironing board, small [sleeve] ironing board, tailor's ham, ham holder
* [[Gravity Iron]]
* Large 8' fabric table
* Small table-top weaving loom, inkle frame loom, warping board, and assorted wooden yarn winders, hand crank yarn winder
* Knitting and crochet needles, Knifty Knitter plastic hoop style knitting looms
* Cricut paper cutter
* Large printmaking drying rack and lighted bench
* Airbrush tools and compressor
* Guillotine paper cutter
* A-Frame wooden easel; small aluminum table top easel
* Silkscreens and squeegees; t-shirt printing machine
* Leather tooling hand tools
* Ball peen hammer
* Hot glue gun
* Staple guns
* Small lamination machine
* 3-Hole punch
* Cutting mat and Xacto knife

== Wish List ==

== Certifications ==

[[Category:Hosted Areas]]
[[Category:Member Manual]]
[[Category:Equipment]]
[[Category:Projects]]
[[Category:Tutorials]]

Adler Patcher

2025-11-04T23:25:37Z

Ugrosse: Typo in name

{{Template:EquipmentPage
| owner=Uwe Grosse
| model=Adler
| serial=SERIAL NUMBER
| arrived= 07/02/23
| where=Arts
| certification=yes
| contact=Arts Area Host
| hackable=no
| value=Unknown
| image =
| hostarea = Arts Area
| doesitwork=yes
}}

The Adler Patcher is probably the most versatile sewing machines we have. The thin bed of this sewing machine allows you to pull most things needing sewing into place. Also the foot can turn 360 degrees to sew from any direction.

[https://youtu.be/g4AJvj_g1yM Video demonstration of the Patcher]

Suggested thread size: 92-277

[https://www.youtube.com/watch?v=4oqmmPugdcA Video of how to wind the bobbin, load the bobbin, and thread the machine]. Note that our threading rod is on the front of the machine, held by a magnet.

===Needle Installation===
[[File:Needle_Orientation_1.jpeg| 600px]]

[[File:Needle_Orientation_2.jpeg| 600px]]

Vote To Buy The Building

2025-06-04T02:56:02Z

Ugrosse: /* Language of the Vote */ Changed loan language to make it encompass multiple loans (owner finance and commercial loan)

== Title==
Vote to Buy the Building
== Sponsor ==
*Nick Hawley
== Co-Sponsors ==
*Lindsay Moore
*Andrew Wingate
*Uwe Grosse
== Vote Results ==
Quorum:[ ]
Yea Votes: [ ]
Nay Votes: [ ]
Present or Abstain: [ ]

== Schedule ==
==== Proposal Date ====
Date this proposal was posted to the membership and a request for a vote date was sent to the Board.

'''[TBD]'''

==== Member Input ====
Does the Sponsor choose to open the language of the vote for changes due to member input? (optional and can be modified at any time)

'''[X] YES [ ] NO'''

==== Vote Announcement and Beginning Date of the Discussion Period ====
The announcement date of the vote proposal is the beginning date of the seven-day (minimum) posting and Member discussion period. (Certain exceptional vote types have longer discussion periods. Check the Bylaws if you are unsure.)'' If the Sponsor has chosen to include member input, suggested edits can be made in a shared document or other collaborative vehicle until the language is locked. The sponsor can stop taking suggestions at any time. ''

'''[TBD]'''

==== Language Lock Date and Start of Voting ====
Five days prior to the Day of the Vote, the vote language is locked, all edits are frozen, and the language of the vote is converted to a pdf file. Ballots that include the pdf are sent to the Membership, and electronic voting begins. '' Note that the minimum discussion period of seven days leaves only two days for changes before the lock takes place. ''

'''[06/12/2025]'''

==== Day of the Vote ====

Date the Board has assigned for the vote. The Day of the Vote is the day the vote closes.

'''[06/17/2025]'''

== Background ==
Our landlord has decided to sell the building at the end of our current lease, in June 2026. It is in our best interest that he sell it to us, rather than anyone else. Moving to another location would be borderline impossible - when we sprawled to the second half of our building, it took the better part of a year to get that done.

== Synopsis ==
The asking price is $1,300,000. Currently we've negotiated to $1,250,000. Our landlord has offered to owner-finance for the first 5 years. We will pay a 20% down payment in 2026, then make 5 years of mortgage payments, then make a balloon payment of the remaining balance. We will need to secure a commercial loan to make that balloon payment. The mortgage payments will be approximately $8,500 per month. We will also be responsible for our property taxes, which are currently around $30,000 per year.

== Language of the Vote ==
We authorize the Pumping Station: One Board of Directors to spend up to $1,300,000 to purchase the building, including any closing costs or other fees. We authorize the Board to secure necessary loans for this purchase, and make interest payments in addition to the principal. We authorize the board to pay property taxes.

[[Category:Votes]]
[[Category:2025 Votes]]

Vote To Buy The Building

2025-06-04T02:51:06Z

Ugrosse: /* Co-Sponsors */

== Title==
Vote to Buy the Building
== Sponsor ==
*Nick Hawley
== Co-Sponsors ==
*Lindsay Moore
*Andrew Wingate
*Uwe Grosse
== Vote Results ==
Quorum:[ ]
Yea Votes: [ ]
Nay Votes: [ ]
Present or Abstain: [ ]

== Schedule ==
==== Proposal Date ====
Date this proposal was posted to the membership and a request for a vote date was sent to the Board.

'''[TBD]'''

==== Member Input ====
Does the Sponsor choose to open the language of the vote for changes due to member input? (optional and can be modified at any time)

'''[X] YES [ ] NO'''

==== Vote Announcement and Beginning Date of the Discussion Period ====
The announcement date of the vote proposal is the beginning date of the seven-day (minimum) posting and Member discussion period. (Certain exceptional vote types have longer discussion periods. Check the Bylaws if you are unsure.)'' If the Sponsor has chosen to include member input, suggested edits can be made in a shared document or other collaborative vehicle until the language is locked. The sponsor can stop taking suggestions at any time. ''

'''[TBD]'''

==== Language Lock Date and Start of Voting ====
Five days prior to the Day of the Vote, the vote language is locked, all edits are frozen, and the language of the vote is converted to a pdf file. Ballots that include the pdf are sent to the Membership, and electronic voting begins. '' Note that the minimum discussion period of seven days leaves only two days for changes before the lock takes place. ''

'''[06/12/2025]'''

==== Day of the Vote ====

Date the Board has assigned for the vote. The Day of the Vote is the day the vote closes.

'''[06/17/2025]'''

== Background ==
Our landlord has decided to sell the building at the end of our current lease, in June 2026. It is in our best interest that he sell it to us, rather than anyone else. Moving to another location would be borderline impossible - when we sprawled to the second half of our building, it took the better part of a year to get that done.

== Synopsis ==
The asking price is $1,300,000. Currently we've negotiated to $1,250,000. Our landlord has offered to owner-finance for the first 5 years. We will pay a 20% down payment in 2026, then make 5 years of mortgage payments, then make a balloon payment of the remaining balance. We will need to secure a commercial loan to make that balloon payment. The mortgage payments will be approximately $8,500 per month. We will also be responsible for our property taxes, which are currently around $30,000 per year.

== Language of the Vote ==
We authorize the Pumping Station: One Board of Directors to spend up to $1,300,000 to purchase the building, including any closing costs or other fees. We authorize the Board to secure a loan for this sum, and make interest payments in addition to the principal. We authorize the board to pay property taxes.

[[Category:Votes]]
[[Category:2025 Votes]]

Authorizations

2025-03-24T18:30:30Z

Ugrosse: Sewing auth text

==[[How Do I Get Authorized?]]==
{{#lst:How Do I Get Authorized?|authmantra}}

Some authorizations are regularly scheduled while others are scheduled on-demand. To schedule an on-demand authorization, members may post in the relevant [[Discord]] channel, or contact a volunteer authorizer directly. Contact information for all current volunteer authorizers can be found at [[Volunteer Positions]].

Note that authorizations requiring a Canvas course, only show you the schedule after you complete the course. Even then sometimes (especially Woodshop) the authorizations are booked up for that month.

=== I am a member looking to get authorized for a tool! ===
Here's how to find out how to get authorized:


<ol><li> '''Read''' [[How Do I Get Authorized?]]
<li> '''Find''' the authorization info in one of these ways:
<ul><li> Scan the QR on the "Authorization Required" sticker on the tool, see example above
<li> Search for the tool's wiki page
<li> Or look through the list on this page
</ul>
<li>'''Follow the instructions in the blue authorization notice box''', see example below
<ul><li> If the blue authorization notice box is missing, ask on [[Discord]] for confirmation the instructions on the page are still accurate</li></ul>
<li> '''Complete the authorization'''
<li> Required: '''Make something cool!'''
</ol>

==⚠️ '''Notice, March 2024 - Confirm authorizations on [[Discord]] first'''==
Double check by verifying on [[Discord]] with how to get authorized for any tool. Please help us out by letting area hosts (or [https://discord.com/channels/1270929620224704544/1308619569828593775 #wiki-love]) know if the information on this page needs to be updated. You are also welcome to update this wiki page yourself. Thanks!

__TOC__
==Wood Shop - [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]==
The [[:Category:Wood_Shop|Wood Shop]] Basic Authorization is a prerequisite for all other authorizations listed in this section. The Basic Authorization is a two-part process:

#[https://canvas.pumpingstationone.org '''Complete the Canvas Course, first''']
#Through the Canvas Calendar '''schedule an in-person authorization'''

If you have trouble you can reach out to [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]] or email [mailto:woodshop@pumpingstationone.org woodshop@pumpingstationone.org].
{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
! scope="col" |Schedule
|-
|Woodshop
| Basic Authorization
|Complete the Canvas Course. A link to schedule an authorization will be shown once you've completed the course. However, often the schedule is booked up for the month and won't show any openings.
|[https://canvas.pumpingstationone.org/courses/40 Woodshop Authorization]
|-
|Woodshop
|Sweet 16 Wood Lathe
|Contact Donzell Gordon to set up a time
|[mailto:donzellphoto@gmail.com Donzell Gordon]
|-
|Woodshop
|Delta Mortiser and Tenon Jig
|Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|-
|Woodshop
|Advanced Bandsaw: Resawing and Maintenance
| Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|-
|Woodshop
|SawStop Dado Stack
| Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|}

==Small Metals - [https://discord.com/channels/1270929620224704544/1270938338760724573 #small-metals-general] on [[Discord]]==
All small metals authorizations are by-request.
{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
|-
|Small Metals
|Basic Authorization
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|-
|Small Metals
|Casting
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|-
|Small Metals
|Hydraulic Press
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|}
Ask for dates and times in [https://discord.com/channels/1270929620224704544/1270938338760724573 #small-metals-general] on [[Discord]].

Please review the wiki pages: '''[[Acetylene_Air_Torch_Jewelry]]''', '''[[Evenheat_810_Kiln]]''', '''[[AIM_Kiln_1413]]''' and '''[[Dyna_Kiln_N100]]'''

==Cold Metals - [https://discord.com/channels/1270929620224704544/1270939023392903228 #cold-metals-general] on [[Discord]]==
All small metals authorizations are by-request.

===[[Tier 1 Cold Metals Authorization]]===
Authorizations for many of the most commonly used metal tools, including the drill press, [[Rockwell Delta 20" Bandsaw|bandsaw]], [[Johnson Bandsaw|Johnson bandsaw]], [[DeWalt Chop Saw|chop saw]], [[Belt Sander|belt sander]], [[Bench Grinder (6in)|bench grinder]], and [[Angle Grinder (4.5in)|angle grinders]], are bundled together into a single session.

The following table generally requires completion of Tier 1 prior to authorization.

{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
|-
| Cold Metals
|Clausing Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|LeBlond Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
| Cold Metals
|Bridgeport Knee Mill
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Grizzly Mini Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Surface Grinder
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Baldor 510 Tool Grinder
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|}
==Hot Metals - [https://discord.com/channels/1270929620224704544/1270938266794721301 #hotmetalshop] on [[Discord]]==
The Hot Metals general auth is a prerequisite for all other authorizations in this area, in addition to any listed prerequisites. Additionally there is a recommended [https://canvas.pumpingstationone.org/courses/65 Canvas course] to help you become familiar with all things Hot Metal.
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|Hot Metals general auth
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Hot_Metals_Authorizers Hot Metals Authorizers]
|-
|[[Big Blasting Cabinet]]
|Contact an Authorizer to set up a time
|-
|[[Belovac Vacuum Forming Machine]]
|[[Viral Authorizations]], Post request to [https://discord.com/channels/1270929620224704544/1270938266794721301 #hotmetalshop] on [[Discord]]
|-
|Powder Coating
|Contact an Authorizer to set up a time
|-
| MIG Welder
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|TIG Welder
|Contact an authorizer to set up a time
|-
|[[CNC Plasma Cutter]]
|Regularly scheduled - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|Handheld Plasma Cutter
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|[[Blacksmithing_Area | Blacksmithing/Forges]]
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|}

==CNC - Lasers - [https://discord.com/channels/1270929620224704544/1270939157484539935 #lasers] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[Universal PLS6.150D 150W Laser Engraver]]
|[https://wiki.pumpingstationone.org/Universal_PLS6.150D_150W_Laser_Engraver#Authorization:_How_to_Get_Authorized Contact Lasers Authorizers]
|-
|[[BOSS LS-3655 150w Laser Engraver]]
|[https://wiki.pumpingstationone.org/BOSS_LS-3655_150w_Laser_Engraver#Authorization Contact Lasers Authorizers]
|-
|[[Universal Maintenance | Universal Laser Maintenance]]
|[https://wiki.pumpingstationone.org/Universal_PLS6.150D_150W_Laser_Engraver#Authorization:_How_to_Get_Authorized Contact Lasers Authorizers]
|-
|[[BOSS Maintenance | Boss Laser Maintenance]]
|[https://wiki.pumpingstationone.org/BOSS_LS-3655_150w_Laser_Engraver#Authorization Contact Lasers Authorizers]
|}

==CNC - 3D Resin (SLA) Printers - [https://discord.com/channels/1270929620224704544/1286074409177714708 #3d-sla-printing] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[Formlabs Form 3 SLA Printer | Form 3 SLA 3D printer]]
|There are no authorizations for this printer. Instead, ask the SLA Printer Area host in [https://discord.com/channels/1270929620224704544/1286074409177714708 Discord]. You will need to supply your file(s) for printing.
|}

==CNC - 3D Filament (FDM) Printers - [https://discord.com/channels/1270929620224704544/12709387556746732558 #3d-printing] on [[Discord]]==
3D printers using filament only require the canvas course, no in person authorization needed.
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[ Prusa i3 3D printer]]
|[https://canvas.pumpingstationone.org/courses/60#Auths are online only through canvas].
|-
|[[ Creality Ender 3 A 3D Printer]]
|[https://canvas.pumpingstationone.org/courses/60#Auths are online only through canvas]. 3D printers using filament only require the canvas course.
|}

==Industrial CNC - [https://discord.com/channels/1270929620224704544/1270939130200850557 #cnc-general] on [[Discord]]==

==== ShopBot ====
There are 2 required classes for complete Shopbot Authorization. The first class is a software-only class to cover CNC concepts and the toolpath and control software. This class is unlimited capacity and generally open to the public. The software-only class is a prerequisite for the second class, the hands-on ShopBot authorization, which will be significantly shortened since it will only cover the specifics of the tool itself.

{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|'''Prerequisites'''
|'''Authorizer(s)'''
|-
|[[ShapeOko2 CNC Router]]
|2D and 3D Auths are scheduled 1:1
|None
|[[User:Newfatmike|Mike Thompson]]
|-
|-
|[[Shopbot PRS CNC router]]
|Regularly scheduled - check the [https://pumpingstationone.org/events/ Events Calendar]. There is also a helpful but not required [https://canvas.pumpingstationone.org/courses/69 Canvas course] going over the basics of 2D CAD using Inkscape.
| None
|David Earl
|-
|[[Tormach 1100 series CNC mill]]
|See the [https://canvas.pumpingstationone.org/courses/30 Canvas course] for authorization information
|Cold Metals general auth, Bridgeport auth
|[[User:Berky93|Alex Berkowitz]]
|}

==2D Printing - [https://discord.com/channels/1270929620224704544/1270938421476720641 #2d-printing] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[https://wiki.pumpingstationone.org/wiki/Mimaki_CJV30-160 Mimaki CJV30-160]
|[https://canvas.pumpingstationone.org/courses/91 Complete the Canvas Course]
|-
|[[Epson Stylus Pro 9800 | Epson Stylus Pro 9800 Large-format Printer]]
|[https://wiki.pumpingstationone.org/Volunteer_Positions#2D_Printers Contact 2D Printing Area Host]
|}

==Graphic Arts & Textiles - [https://discord.com/channels/1270929620224704544/1270938360394809489 #arts-general] on [[Discord]]==
==== Sewing Machines ====
No authorization is required for domestic sewing machines located under the big table. Industrial sewing machines along the wall and windows require authorization.

{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|Tier 1 Sewing Machines (Juki serger, Juki straight stitch, Singer zig-zag, Juki cylinder arm)
|Check [https://discord.com/channels/1270929620224704544/1285119362830831676#sewing #sewing] for upcoming auths
|-
|Leather Sewing Machines (Cowboy heavy duty stitcher, Adler patcher, Juki cylinder arm)
|Check [https://discord.com/channels/1270929620224704544/1285119362830831676 #sewing] for upcoming auths
|-
|Embroidery Machine
|Check [https://discord.com/channels/1270929620224704544/1271315999664242719 #embroidery] for upcoming auths
|}
==Electronics - [https://discord.com/channels/1270929620224704544/1270933607011057776 #⚡-electronics-general] on [[Discord]]==

The Electronics area currently has no authorizations. However, the parts provided in Electronics aren't free. Please make a donation in the lockbox on the left side of the parts wall for anything you take.
==Kitchen - [https://discord.com/channels/1270929620224704544/1270938143948013699 #kitchen-general] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|'''Prerequisites'''
|'''Authorizer(s)'''
|-
|[[Java Master 2002 Coffee Roaster]]
|Contact an authorizer to set up a time
|Acquire 1 lb green coffee beans, which can be done at [https://www.sweetmarias.com/ Sweet Maria’s]
|Ryan Pierce
|}

{{Template:ToolAuthorization
|authslug = hotairballoon
|authorization_name = Hot Air Balloon
|authorizer = [[User:Jane_hacker|Jane Hacker]]
|schedule_frequency = Twice a week, see Canvas
|discord_channel_link = https://discord.com/channels/1270929620224704544/1271319468055855165
|discord_channel_name = #aviation-club
|prerequisites = Completed auth for [[Parachute]]
|step1 = [https://canvas.pumpingstationone.org/courses/40 Complete the Canvas course]
|step2 = Use Canvas to schedule with the next available in-person auth
|step3 = Complete the in-person auth
|step4 =
|step5 =
|required_materials = Aviator goggles, cape, propane.
|notes = Will be rescheduled if there's bad weather.
}}

{| border="0" cellpadding="32" style="margin: 20px auto 20px auto; text-align:center;"
![[File:Authorization-required.png|alt=|center|328x328px]]
![[File:Figners-in-gears-sign.jpg|center|192x192px]]
|}

=New Tool Authorization Template=
Information for all authorizations will be maintained in this [[Authorizations]] page, and individual tool pages (or wherever else) can link back here. This creates one simple place to go and manage information regarding an auth without having to hunt down the individual tool or content on multiple pages.

Copy the example in [[Template:ToolAuthorization]] and paste it into this [[Authorizations]] page under the correct area/section, then fill out the needed fields. Once the page saves, above the filled out template there will be a <code><nowiki>{{#lst:Authorizations|authid}}</nowiki></code> code snippet specific for that filled out auth. Copy and paste this snippet into the tools page that requires the authorization. If you later need to update the auth information, return to this page and edit it here.
==Sample Template Code==
<pre>{{Template:ToolAuthorization
|authslug = hotairballoon
|authorization_name = Hot Air Balloon
|authorizer = [[User:Jane_hacker|Jane Hacker]]
|schedule_frequency = Twice a week, see Canvas
|discord_channel_link = https://discord.com/channels/1270929620224704544/1271319468055855165
|discord_channel_name = #random
|step1 = [https://canvas.pumpingstationone.org/courses/40 Complete the Canvas course]
|step2 = Use Canvas to schedule with the next available in-person auth
|step3 = Complete the in-person auth
|description = Please remember to bring aviator goggles and propane
}}</pre>
==Example:==

__FORCETOC__
__NOEDITSECTION__

Authorizations

2025-03-24T18:25:55Z

Ugrosse: Added link for #embroidery

==[[How Do I Get Authorized?]]==
{{#lst:How Do I Get Authorized?|authmantra}}

Some authorizations are regularly scheduled while others are scheduled on-demand. To schedule an on-demand authorization, members may post in the relevant [[Discord]] channel, or contact a volunteer authorizer directly. Contact information for all current volunteer authorizers can be found at [[Volunteer Positions]].

Note that authorizations requiring a Canvas course, only show you the schedule after you complete the course. Even then sometimes (especially Woodshop) the authorizations are booked up for that month.

=== I am a member looking to get authorized for a tool! ===
Here's how to find out how to get authorized:


<ol><li> '''Read''' [[How Do I Get Authorized?]]
<li> '''Find''' the authorization info in one of these ways:
<ul><li> Scan the QR on the "Authorization Required" sticker on the tool, see example above
<li> Search for the tool's wiki page
<li> Or look through the list on this page
</ul>
<li>'''Follow the instructions in the blue authorization notice box''', see example below
<ul><li> If the blue authorization notice box is missing, ask on [[Discord]] for confirmation the instructions on the page are still accurate</li></ul>
<li> '''Complete the authorization'''
<li> Required: '''Make something cool!'''
</ol>

==⚠️ '''Notice, March 2024 - Confirm authorizations on [[Discord]] first'''==
Double check by verifying on [[Discord]] with how to get authorized for any tool. Please help us out by letting area hosts (or [https://discord.com/channels/1270929620224704544/1308619569828593775 #wiki-love]) know if the information on this page needs to be updated. You are also welcome to update this wiki page yourself. Thanks!

__TOC__
==Wood Shop - [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]==
The [[:Category:Wood_Shop|Wood Shop]] Basic Authorization is a prerequisite for all other authorizations listed in this section. The Basic Authorization is a two-part process:

#[https://canvas.pumpingstationone.org '''Complete the Canvas Course, first''']
#Through the Canvas Calendar '''schedule an in-person authorization'''

If you have trouble you can reach out to [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]] or email [mailto:woodshop@pumpingstationone.org woodshop@pumpingstationone.org].
{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
! scope="col" |Schedule
|-
|Woodshop
| Basic Authorization
|Complete the Canvas Course. A link to schedule an authorization will be shown once you've completed the course. However, often the schedule is booked up for the month and won't show any openings.
|[https://canvas.pumpingstationone.org/courses/40 Woodshop Authorization]
|-
|Woodshop
|Sweet 16 Wood Lathe
|Contact Donzell Gordon to set up a time
|[mailto:donzellphoto@gmail.com Donzell Gordon]
|-
|Woodshop
|Delta Mortiser and Tenon Jig
|Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|-
|Woodshop
|Advanced Bandsaw: Resawing and Maintenance
| Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|-
|Woodshop
|SawStop Dado Stack
| Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|}

==Small Metals - [https://discord.com/channels/1270929620224704544/1270938338760724573 #small-metals-general] on [[Discord]]==
All small metals authorizations are by-request.
{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
|-
|Small Metals
|Basic Authorization
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|-
|Small Metals
|Casting
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|-
|Small Metals
|Hydraulic Press
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|}
Ask for dates and times in [https://discord.com/channels/1270929620224704544/1270938338760724573 #small-metals-general] on [[Discord]].

Please review the wiki pages: '''[[Acetylene_Air_Torch_Jewelry]]''', '''[[Evenheat_810_Kiln]]''', '''[[AIM_Kiln_1413]]''' and '''[[Dyna_Kiln_N100]]'''

==Cold Metals - [https://discord.com/channels/1270929620224704544/1270939023392903228 #cold-metals-general] on [[Discord]]==
All small metals authorizations are by-request.

===[[Tier 1 Cold Metals Authorization]]===
Authorizations for many of the most commonly used metal tools, including the drill press, [[Rockwell Delta 20" Bandsaw|bandsaw]], [[Johnson Bandsaw|Johnson bandsaw]], [[DeWalt Chop Saw|chop saw]], [[Belt Sander|belt sander]], [[Bench Grinder (6in)|bench grinder]], and [[Angle Grinder (4.5in)|angle grinders]], are bundled together into a single session.

The following table generally requires completion of Tier 1 prior to authorization.

{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
|-
| Cold Metals
|Clausing Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|LeBlond Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
| Cold Metals
|Bridgeport Knee Mill
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Grizzly Mini Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Surface Grinder
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Baldor 510 Tool Grinder
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|}
==Hot Metals - [https://discord.com/channels/1270929620224704544/1270938266794721301 #hotmetalshop] on [[Discord]]==
The Hot Metals general auth is a prerequisite for all other authorizations in this area, in addition to any listed prerequisites. Additionally there is a recommended [https://canvas.pumpingstationone.org/courses/65 Canvas course] to help you become familiar with all things Hot Metal.
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|Hot Metals general auth
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Hot_Metals_Authorizers Hot Metals Authorizers]
|-
|[[Big Blasting Cabinet]]
|Contact an Authorizer to set up a time
|-
|[[Belovac Vacuum Forming Machine]]
|[[Viral Authorizations]], Post request to [https://discord.com/channels/1270929620224704544/1270938266794721301 #hotmetalshop] on [[Discord]]
|-
|Powder Coating
|Contact an Authorizer to set up a time
|-
| MIG Welder
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|TIG Welder
|Contact an authorizer to set up a time
|-
|[[CNC Plasma Cutter]]
|Regularly scheduled - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|Handheld Plasma Cutter
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|[[Blacksmithing_Area | Blacksmithing/Forges]]
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|}

==CNC - Lasers - [https://discord.com/channels/1270929620224704544/1270939157484539935 #lasers] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[Universal PLS6.150D 150W Laser Engraver]]
|[https://wiki.pumpingstationone.org/Universal_PLS6.150D_150W_Laser_Engraver#Authorization:_How_to_Get_Authorized Contact Lasers Authorizers]
|-
|[[BOSS LS-3655 150w Laser Engraver]]
|[https://wiki.pumpingstationone.org/BOSS_LS-3655_150w_Laser_Engraver#Authorization Contact Lasers Authorizers]
|-
|[[Universal Maintenance | Universal Laser Maintenance]]
|[https://wiki.pumpingstationone.org/Universal_PLS6.150D_150W_Laser_Engraver#Authorization:_How_to_Get_Authorized Contact Lasers Authorizers]
|-
|[[BOSS Maintenance | Boss Laser Maintenance]]
|[https://wiki.pumpingstationone.org/BOSS_LS-3655_150w_Laser_Engraver#Authorization Contact Lasers Authorizers]
|}

==CNC - 3D Resin (SLA) Printers - [https://discord.com/channels/1270929620224704544/1286074409177714708 #3d-sla-printing] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[Formlabs Form 3 SLA Printer | Form 3 SLA 3D printer]]
|There are no authorizations for this printer. Instead, ask the SLA Printer Area host in [https://discord.com/channels/1270929620224704544/1286074409177714708 Discord]. You will need to supply your file(s) for printing.
|}

==CNC - 3D Filament (FDM) Printers - [https://discord.com/channels/1270929620224704544/12709387556746732558 #3d-printing] on [[Discord]]==
3D printers using filament only require the canvas course, no in person authorization needed.
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[ Prusa i3 3D printer]]
|[https://canvas.pumpingstationone.org/courses/60#Auths are online only through canvas].
|-
|[[ Creality Ender 3 A 3D Printer]]
|[https://canvas.pumpingstationone.org/courses/60#Auths are online only through canvas]. 3D printers using filament only require the canvas course.
|}

==Industrial CNC - [https://discord.com/channels/1270929620224704544/1270939130200850557 #cnc-general] on [[Discord]]==

==== ShopBot ====
There are 2 required classes for complete Shopbot Authorization. The first class is a software-only class to cover CNC concepts and the toolpath and control software. This class is unlimited capacity and generally open to the public. The software-only class is a prerequisite for the second class, the hands-on ShopBot authorization, which will be significantly shortened since it will only cover the specifics of the tool itself.

{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|'''Prerequisites'''
|'''Authorizer(s)'''
|-
|[[ShapeOko2 CNC Router]]
|2D and 3D Auths are scheduled 1:1
|None
|[[User:Newfatmike|Mike Thompson]]
|-
|-
|[[Shopbot PRS CNC router]]
|Regularly scheduled - check the [https://pumpingstationone.org/events/ Events Calendar]. There is also a helpful but not required [https://canvas.pumpingstationone.org/courses/69 Canvas course] going over the basics of 2D CAD using Inkscape.
| None
|David Earl
|-
|[[Tormach 1100 series CNC mill]]
|See the [https://canvas.pumpingstationone.org/courses/30 Canvas course] for authorization information
|Cold Metals general auth, Bridgeport auth
|[[User:Berky93|Alex Berkowitz]]
|}

==2D Printing - [https://discord.com/channels/1270929620224704544/1270938421476720641 #2d-printing] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[https://wiki.pumpingstationone.org/wiki/Mimaki_CJV30-160 Mimaki CJV30-160]
|[https://canvas.pumpingstationone.org/courses/91 Complete the Canvas Course]
|-
|[[Epson Stylus Pro 9800 | Epson Stylus Pro 9800 Large-format Printer]]
|[https://wiki.pumpingstationone.org/Volunteer_Positions#2D_Printers Contact 2D Printing Area Host]
|}

==Graphic Arts & Textiles - [https://discord.com/channels/1270929620224704544/1270938360394809489 #arts-general] on [[Discord]]==
==== Sewing Machines ====
No certification is required for domestic sewing machines located under the big table.

{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|Tier 1 Sewing Machines
|Check [https://discord.com/channels/1270929620224704544/1285119362830831676#sewing #sewing] for upcoming auths
|-
|Leather Sewing Machines
|Check [https://discord.com/channels/1270929620224704544/1285119362830831676 #sewing] for upcoming auths
|-
|Embroidery Machine
|Check [https://discord.com/channels/1270929620224704544/1271315999664242719 #embroidery] for upcoming auths
|}
==Electronics - [https://discord.com/channels/1270929620224704544/1270933607011057776 #⚡-electronics-general] on [[Discord]]==

The Electronics area currently has no authorizations. However, the parts provided in Electronics aren't free. Please make a donation in the lockbox on the left side of the parts wall for anything you take.
==Kitchen - [https://discord.com/channels/1270929620224704544/1270938143948013699 #kitchen-general] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|'''Prerequisites'''
|'''Authorizer(s)'''
|-
|[[Java Master 2002 Coffee Roaster]]
|Contact an authorizer to set up a time
|Acquire 1 lb green coffee beans, which can be done at [https://www.sweetmarias.com/ Sweet Maria’s]
|Ryan Pierce
|}

{{Template:ToolAuthorization
|authslug = hotairballoon
|authorization_name = Hot Air Balloon
|authorizer = [[User:Jane_hacker|Jane Hacker]]
|schedule_frequency = Twice a week, see Canvas
|discord_channel_link = https://discord.com/channels/1270929620224704544/1271319468055855165
|discord_channel_name = #aviation-club
|prerequisites = Completed auth for [[Parachute]]
|step1 = [https://canvas.pumpingstationone.org/courses/40 Complete the Canvas course]
|step2 = Use Canvas to schedule with the next available in-person auth
|step3 = Complete the in-person auth
|step4 =
|step5 =
|required_materials = Aviator goggles, cape, propane.
|notes = Will be rescheduled if there's bad weather.
}}

{| border="0" cellpadding="32" style="margin: 20px auto 20px auto; text-align:center;"
![[File:Authorization-required.png|alt=|center|328x328px]]
![[File:Figners-in-gears-sign.jpg|center|192x192px]]
|}

=New Tool Authorization Template=
Information for all authorizations will be maintained in this [[Authorizations]] page, and individual tool pages (or wherever else) can link back here. This creates one simple place to go and manage information regarding an auth without having to hunt down the individual tool or content on multiple pages.

Copy the example in [[Template:ToolAuthorization]] and paste it into this [[Authorizations]] page under the correct area/section, then fill out the needed fields. Once the page saves, above the filled out template there will be a <code><nowiki>{{#lst:Authorizations|authid}}</nowiki></code> code snippet specific for that filled out auth. Copy and paste this snippet into the tools page that requires the authorization. If you later need to update the auth information, return to this page and edit it here.
==Sample Template Code==
<pre>{{Template:ToolAuthorization
|authslug = hotairballoon
|authorization_name = Hot Air Balloon
|authorizer = [[User:Jane_hacker|Jane Hacker]]
|schedule_frequency = Twice a week, see Canvas
|discord_channel_link = https://discord.com/channels/1270929620224704544/1271319468055855165
|discord_channel_name = #random
|step1 = [https://canvas.pumpingstationone.org/courses/40 Complete the Canvas course]
|step2 = Use Canvas to schedule with the next available in-person auth
|step3 = Complete the in-person auth
|description = Please remember to bring aviator goggles and propane
}}</pre>
==Example:==

__FORCETOC__
__NOEDITSECTION__

Authorizations

2025-03-24T18:24:35Z

Ugrosse: Added links to #sewing

==[[How Do I Get Authorized?]]==
{{#lst:How Do I Get Authorized?|authmantra}}

Some authorizations are regularly scheduled while others are scheduled on-demand. To schedule an on-demand authorization, members may post in the relevant [[Discord]] channel, or contact a volunteer authorizer directly. Contact information for all current volunteer authorizers can be found at [[Volunteer Positions]].

Note that authorizations requiring a Canvas course, only show you the schedule after you complete the course. Even then sometimes (especially Woodshop) the authorizations are booked up for that month.

=== I am a member looking to get authorized for a tool! ===
Here's how to find out how to get authorized:


<ol><li> '''Read''' [[How Do I Get Authorized?]]
<li> '''Find''' the authorization info in one of these ways:
<ul><li> Scan the QR on the "Authorization Required" sticker on the tool, see example above
<li> Search for the tool's wiki page
<li> Or look through the list on this page
</ul>
<li>'''Follow the instructions in the blue authorization notice box''', see example below
<ul><li> If the blue authorization notice box is missing, ask on [[Discord]] for confirmation the instructions on the page are still accurate</li></ul>
<li> '''Complete the authorization'''
<li> Required: '''Make something cool!'''
</ol>

==⚠️ '''Notice, March 2024 - Confirm authorizations on [[Discord]] first'''==
Double check by verifying on [[Discord]] with how to get authorized for any tool. Please help us out by letting area hosts (or [https://discord.com/channels/1270929620224704544/1308619569828593775 #wiki-love]) know if the information on this page needs to be updated. You are also welcome to update this wiki page yourself. Thanks!

__TOC__
==Wood Shop - [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]==
The [[:Category:Wood_Shop|Wood Shop]] Basic Authorization is a prerequisite for all other authorizations listed in this section. The Basic Authorization is a two-part process:

#[https://canvas.pumpingstationone.org '''Complete the Canvas Course, first''']
#Through the Canvas Calendar '''schedule an in-person authorization'''

If you have trouble you can reach out to [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]] or email [mailto:woodshop@pumpingstationone.org woodshop@pumpingstationone.org].
{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
! scope="col" |Schedule
|-
|Woodshop
| Basic Authorization
|Complete the Canvas Course. A link to schedule an authorization will be shown once you've completed the course. However, often the schedule is booked up for the month and won't show any openings.
|[https://canvas.pumpingstationone.org/courses/40 Woodshop Authorization]
|-
|Woodshop
|Sweet 16 Wood Lathe
|Contact Donzell Gordon to set up a time
|[mailto:donzellphoto@gmail.com Donzell Gordon]
|-
|Woodshop
|Delta Mortiser and Tenon Jig
|Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|-
|Woodshop
|Advanced Bandsaw: Resawing and Maintenance
| Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|-
|Woodshop
|SawStop Dado Stack
| Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|}

==Small Metals - [https://discord.com/channels/1270929620224704544/1270938338760724573 #small-metals-general] on [[Discord]]==
All small metals authorizations are by-request.
{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
|-
|Small Metals
|Basic Authorization
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|-
|Small Metals
|Casting
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|-
|Small Metals
|Hydraulic Press
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|}
Ask for dates and times in [https://discord.com/channels/1270929620224704544/1270938338760724573 #small-metals-general] on [[Discord]].

Please review the wiki pages: '''[[Acetylene_Air_Torch_Jewelry]]''', '''[[Evenheat_810_Kiln]]''', '''[[AIM_Kiln_1413]]''' and '''[[Dyna_Kiln_N100]]'''

==Cold Metals - [https://discord.com/channels/1270929620224704544/1270939023392903228 #cold-metals-general] on [[Discord]]==
All small metals authorizations are by-request.

===[[Tier 1 Cold Metals Authorization]]===
Authorizations for many of the most commonly used metal tools, including the drill press, [[Rockwell Delta 20" Bandsaw|bandsaw]], [[Johnson Bandsaw|Johnson bandsaw]], [[DeWalt Chop Saw|chop saw]], [[Belt Sander|belt sander]], [[Bench Grinder (6in)|bench grinder]], and [[Angle Grinder (4.5in)|angle grinders]], are bundled together into a single session.

The following table generally requires completion of Tier 1 prior to authorization.

{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
|-
| Cold Metals
|Clausing Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|LeBlond Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
| Cold Metals
|Bridgeport Knee Mill
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Grizzly Mini Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Surface Grinder
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Baldor 510 Tool Grinder
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|}
==Hot Metals - [https://discord.com/channels/1270929620224704544/1270938266794721301 #hotmetalshop] on [[Discord]]==
The Hot Metals general auth is a prerequisite for all other authorizations in this area, in addition to any listed prerequisites. Additionally there is a recommended [https://canvas.pumpingstationone.org/courses/65 Canvas course] to help you become familiar with all things Hot Metal.
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|Hot Metals general auth
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Hot_Metals_Authorizers Hot Metals Authorizers]
|-
|[[Big Blasting Cabinet]]
|Contact an Authorizer to set up a time
|-
|[[Belovac Vacuum Forming Machine]]
|[[Viral Authorizations]], Post request to [https://discord.com/channels/1270929620224704544/1270938266794721301 #hotmetalshop] on [[Discord]]
|-
|Powder Coating
|Contact an Authorizer to set up a time
|-
| MIG Welder
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|TIG Welder
|Contact an authorizer to set up a time
|-
|[[CNC Plasma Cutter]]
|Regularly scheduled - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|Handheld Plasma Cutter
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|[[Blacksmithing_Area | Blacksmithing/Forges]]
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|}

==CNC - Lasers - [https://discord.com/channels/1270929620224704544/1270939157484539935 #lasers] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[Universal PLS6.150D 150W Laser Engraver]]
|[https://wiki.pumpingstationone.org/Universal_PLS6.150D_150W_Laser_Engraver#Authorization:_How_to_Get_Authorized Contact Lasers Authorizers]
|-
|[[BOSS LS-3655 150w Laser Engraver]]
|[https://wiki.pumpingstationone.org/BOSS_LS-3655_150w_Laser_Engraver#Authorization Contact Lasers Authorizers]
|-
|[[Universal Maintenance | Universal Laser Maintenance]]
|[https://wiki.pumpingstationone.org/Universal_PLS6.150D_150W_Laser_Engraver#Authorization:_How_to_Get_Authorized Contact Lasers Authorizers]
|-
|[[BOSS Maintenance | Boss Laser Maintenance]]
|[https://wiki.pumpingstationone.org/BOSS_LS-3655_150w_Laser_Engraver#Authorization Contact Lasers Authorizers]
|}

==CNC - 3D Resin (SLA) Printers - [https://discord.com/channels/1270929620224704544/1286074409177714708 #3d-sla-printing] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[Formlabs Form 3 SLA Printer | Form 3 SLA 3D printer]]
|There are no authorizations for this printer. Instead, ask the SLA Printer Area host in [https://discord.com/channels/1270929620224704544/1286074409177714708 Discord]. You will need to supply your file(s) for printing.
|}

==CNC - 3D Filament (FDM) Printers - [https://discord.com/channels/1270929620224704544/12709387556746732558 #3d-printing] on [[Discord]]==
3D printers using filament only require the canvas course, no in person authorization needed.
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[ Prusa i3 3D printer]]
|[https://canvas.pumpingstationone.org/courses/60#Auths are online only through canvas].
|-
|[[ Creality Ender 3 A 3D Printer]]
|[https://canvas.pumpingstationone.org/courses/60#Auths are online only through canvas]. 3D printers using filament only require the canvas course.
|}

==Industrial CNC - [https://discord.com/channels/1270929620224704544/1270939130200850557 #cnc-general] on [[Discord]]==

==== ShopBot ====
There are 2 required classes for complete Shopbot Authorization. The first class is a software-only class to cover CNC concepts and the toolpath and control software. This class is unlimited capacity and generally open to the public. The software-only class is a prerequisite for the second class, the hands-on ShopBot authorization, which will be significantly shortened since it will only cover the specifics of the tool itself.

{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|'''Prerequisites'''
|'''Authorizer(s)'''
|-
|[[ShapeOko2 CNC Router]]
|2D and 3D Auths are scheduled 1:1
|None
|[[User:Newfatmike|Mike Thompson]]
|-
|-
|[[Shopbot PRS CNC router]]
|Regularly scheduled - check the [https://pumpingstationone.org/events/ Events Calendar]. There is also a helpful but not required [https://canvas.pumpingstationone.org/courses/69 Canvas course] going over the basics of 2D CAD using Inkscape.
| None
|David Earl
|-
|[[Tormach 1100 series CNC mill]]
|See the [https://canvas.pumpingstationone.org/courses/30 Canvas course] for authorization information
|Cold Metals general auth, Bridgeport auth
|[[User:Berky93|Alex Berkowitz]]
|}

==2D Printing - [https://discord.com/channels/1270929620224704544/1270938421476720641 #2d-printing] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[https://wiki.pumpingstationone.org/wiki/Mimaki_CJV30-160 Mimaki CJV30-160]
|[https://canvas.pumpingstationone.org/courses/91 Complete the Canvas Course]
|-
|[[Epson Stylus Pro 9800 | Epson Stylus Pro 9800 Large-format Printer]]
|[https://wiki.pumpingstationone.org/Volunteer_Positions#2D_Printers Contact 2D Printing Area Host]
|}

==Graphic Arts & Textiles - [https://discord.com/channels/1270929620224704544/1270938360394809489 #arts-general] on [[Discord]]==
==== Sewing Machines ====
No certification is required for domestic sewing machines located under the big table.

{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|Tier 1 Sewing Machines
|Check [https://discord.com/channels/1270929620224704544/1285119362830831676#sewing #sewing] for upcoming auths
|-
|Leather Sewing Machines
|Check [https://discord.com/channels/1270929620224704544/1285119362830831676 #sewing] for upcoming auths
|-
|Embroidery Machine
|Check #embroidery for upcoming auths
|}
==Electronics - [https://discord.com/channels/1270929620224704544/1270933607011057776 #⚡-electronics-general] on [[Discord]]==

The Electronics area currently has no authorizations. However, the parts provided in Electronics aren't free. Please make a donation in the lockbox on the left side of the parts wall for anything you take.
==Kitchen - [https://discord.com/channels/1270929620224704544/1270938143948013699 #kitchen-general] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|'''Prerequisites'''
|'''Authorizer(s)'''
|-
|[[Java Master 2002 Coffee Roaster]]
|Contact an authorizer to set up a time
|Acquire 1 lb green coffee beans, which can be done at [https://www.sweetmarias.com/ Sweet Maria’s]
|Ryan Pierce
|}

{{Template:ToolAuthorization
|authslug = hotairballoon
|authorization_name = Hot Air Balloon
|authorizer = [[User:Jane_hacker|Jane Hacker]]
|schedule_frequency = Twice a week, see Canvas
|discord_channel_link = https://discord.com/channels/1270929620224704544/1271319468055855165
|discord_channel_name = #aviation-club
|prerequisites = Completed auth for [[Parachute]]
|step1 = [https://canvas.pumpingstationone.org/courses/40 Complete the Canvas course]
|step2 = Use Canvas to schedule with the next available in-person auth
|step3 = Complete the in-person auth
|step4 =
|step5 =
|required_materials = Aviator goggles, cape, propane.
|notes = Will be rescheduled if there's bad weather.
}}

{| border="0" cellpadding="32" style="margin: 20px auto 20px auto; text-align:center;"
![[File:Authorization-required.png|alt=|center|328x328px]]
![[File:Figners-in-gears-sign.jpg|center|192x192px]]
|}

=New Tool Authorization Template=
Information for all authorizations will be maintained in this [[Authorizations]] page, and individual tool pages (or wherever else) can link back here. This creates one simple place to go and manage information regarding an auth without having to hunt down the individual tool or content on multiple pages.

Copy the example in [[Template:ToolAuthorization]] and paste it into this [[Authorizations]] page under the correct area/section, then fill out the needed fields. Once the page saves, above the filled out template there will be a <code><nowiki>{{#lst:Authorizations|authid}}</nowiki></code> code snippet specific for that filled out auth. Copy and paste this snippet into the tools page that requires the authorization. If you later need to update the auth information, return to this page and edit it here.
==Sample Template Code==
<pre>{{Template:ToolAuthorization
|authslug = hotairballoon
|authorization_name = Hot Air Balloon
|authorizer = [[User:Jane_hacker|Jane Hacker]]
|schedule_frequency = Twice a week, see Canvas
|discord_channel_link = https://discord.com/channels/1270929620224704544/1271319468055855165
|discord_channel_name = #random
|step1 = [https://canvas.pumpingstationone.org/courses/40 Complete the Canvas course]
|step2 = Use Canvas to schedule with the next available in-person auth
|step3 = Complete the in-person auth
|description = Please remember to bring aviator goggles and propane
}}</pre>
==Example:==

__FORCETOC__
__NOEDITSECTION__

Authorizations

2025-03-24T18:15:17Z

Ugrosse: Updated the Sewing Authorization section

==[[How Do I Get Authorized?]]==
{{#lst:How Do I Get Authorized?|authmantra}}

Some authorizations are regularly scheduled while others are scheduled on-demand. To schedule an on-demand authorization, members may post in the relevant [[Discord]] channel, or contact a volunteer authorizer directly. Contact information for all current volunteer authorizers can be found at [[Volunteer Positions]].

Note that authorizations requiring a Canvas course, only show you the schedule after you complete the course. Even then sometimes (especially Woodshop) the authorizations are booked up for that month.

=== I am a member looking to get authorized for a tool! ===
Here's how to find out how to get authorized:


<ol><li> '''Read''' [[How Do I Get Authorized?]]
<li> '''Find''' the authorization info in one of these ways:
<ul><li> Scan the QR on the "Authorization Required" sticker on the tool, see example above
<li> Search for the tool's wiki page
<li> Or look through the list on this page
</ul>
<li>'''Follow the instructions in the blue authorization notice box''', see example below
<ul><li> If the blue authorization notice box is missing, ask on [[Discord]] for confirmation the instructions on the page are still accurate</li></ul>
<li> '''Complete the authorization'''
<li> Required: '''Make something cool!'''
</ol>

==⚠️ '''Notice, March 2024 - Confirm authorizations on [[Discord]] first'''==
Double check by verifying on [[Discord]] with how to get authorized for any tool. Please help us out by letting area hosts (or [https://discord.com/channels/1270929620224704544/1308619569828593775 #wiki-love]) know if the information on this page needs to be updated. You are also welcome to update this wiki page yourself. Thanks!

__TOC__
==Wood Shop - [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]==
The [[:Category:Wood_Shop|Wood Shop]] Basic Authorization is a prerequisite for all other authorizations listed in this section. The Basic Authorization is a two-part process:

#[https://canvas.pumpingstationone.org '''Complete the Canvas Course, first''']
#Through the Canvas Calendar '''schedule an in-person authorization'''

If you have trouble you can reach out to [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]] or email [mailto:woodshop@pumpingstationone.org woodshop@pumpingstationone.org].
{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
! scope="col" |Schedule
|-
|Woodshop
| Basic Authorization
|Complete the Canvas Course. A link to schedule an authorization will be shown once you've completed the course. However, often the schedule is booked up for the month and won't show any openings.
|[https://canvas.pumpingstationone.org/courses/40 Woodshop Authorization]
|-
|Woodshop
|Sweet 16 Wood Lathe
|Contact Donzell Gordon to set up a time
|[mailto:donzellphoto@gmail.com Donzell Gordon]
|-
|Woodshop
|Delta Mortiser and Tenon Jig
|Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|-
|Woodshop
|Advanced Bandsaw: Resawing and Maintenance
| Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|-
|Woodshop
|SawStop Dado Stack
| Ask in [https://discord.com/channels/1270929620224704544/1270939083685892229 #woodshop-general] on [[Discord]]
|
|}

==Small Metals - [https://discord.com/channels/1270929620224704544/1270938338760724573 #small-metals-general] on [[Discord]]==
All small metals authorizations are by-request.
{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
|-
|Small Metals
|Basic Authorization
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|-
|Small Metals
|Casting
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|-
|Small Metals
|Hydraulic Press
|[[Volunteer Positions#Small Metals Authorizer|Small Metals Authorizers]]
|}
Ask for dates and times in [https://discord.com/channels/1270929620224704544/1270938338760724573 #small-metals-general] on [[Discord]].

Please review the wiki pages: '''[[Acetylene_Air_Torch_Jewelry]]''', '''[[Evenheat_810_Kiln]]''', '''[[AIM_Kiln_1413]]''' and '''[[Dyna_Kiln_N100]]'''

==Cold Metals - [https://discord.com/channels/1270929620224704544/1270939023392903228 #cold-metals-general] on [[Discord]]==
All small metals authorizations are by-request.

===[[Tier 1 Cold Metals Authorization]]===
Authorizations for many of the most commonly used metal tools, including the drill press, [[Rockwell Delta 20" Bandsaw|bandsaw]], [[Johnson Bandsaw|Johnson bandsaw]], [[DeWalt Chop Saw|chop saw]], [[Belt Sander|belt sander]], [[Bench Grinder (6in)|bench grinder]], and [[Angle Grinder (4.5in)|angle grinders]], are bundled together into a single session.

The following table generally requires completion of Tier 1 prior to authorization.

{| class="wikitable sortable"
|-
! scope="col" |Area
! scope="col" |Authorization
! scope="col" |Contact
|-
| Cold Metals
|Clausing Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|LeBlond Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
| Cold Metals
|Bridgeport Knee Mill
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Grizzly Mini Metal Lathe
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Surface Grinder
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|-
|Cold Metals
|Baldor 510 Tool Grinder
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Cold_Metals_Authorizers Cold Metals Authorizers]
|}
==Hot Metals - [https://discord.com/channels/1270929620224704544/1270938266794721301 #hotmetalshop] on [[Discord]]==
The Hot Metals general auth is a prerequisite for all other authorizations in this area, in addition to any listed prerequisites. Additionally there is a recommended [https://canvas.pumpingstationone.org/courses/65 Canvas course] to help you become familiar with all things Hot Metal.
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|Hot Metals general auth
|[https://wiki.pumpingstationone.org/Volunteer_Positions#Hot_Metals_Authorizers Hot Metals Authorizers]
|-
|[[Big Blasting Cabinet]]
|Contact an Authorizer to set up a time
|-
|[[Belovac Vacuum Forming Machine]]
|[[Viral Authorizations]], Post request to [https://discord.com/channels/1270929620224704544/1270938266794721301 #hotmetalshop] on [[Discord]]
|-
|Powder Coating
|Contact an Authorizer to set up a time
|-
| MIG Welder
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|TIG Welder
|Contact an authorizer to set up a time
|-
|[[CNC Plasma Cutter]]
|Regularly scheduled - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|Handheld Plasma Cutter
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|-
|[[Blacksmithing_Area | Blacksmithing/Forges]]
|Auths available during office hours - check the [https://pumpingstationone.org/events/ Events Calendar]
|}

==CNC - Lasers - [https://discord.com/channels/1270929620224704544/1270939157484539935 #lasers] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[Universal PLS6.150D 150W Laser Engraver]]
|[https://wiki.pumpingstationone.org/Universal_PLS6.150D_150W_Laser_Engraver#Authorization:_How_to_Get_Authorized Contact Lasers Authorizers]
|-
|[[BOSS LS-3655 150w Laser Engraver]]
|[https://wiki.pumpingstationone.org/BOSS_LS-3655_150w_Laser_Engraver#Authorization Contact Lasers Authorizers]
|-
|[[Universal Maintenance | Universal Laser Maintenance]]
|[https://wiki.pumpingstationone.org/Universal_PLS6.150D_150W_Laser_Engraver#Authorization:_How_to_Get_Authorized Contact Lasers Authorizers]
|-
|[[BOSS Maintenance | Boss Laser Maintenance]]
|[https://wiki.pumpingstationone.org/BOSS_LS-3655_150w_Laser_Engraver#Authorization Contact Lasers Authorizers]
|}

==CNC - 3D Resin (SLA) Printers - [https://discord.com/channels/1270929620224704544/1286074409177714708 #3d-sla-printing] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[Formlabs Form 3 SLA Printer | Form 3 SLA 3D printer]]
|There are no authorizations for this printer. Instead, ask the SLA Printer Area host in [https://discord.com/channels/1270929620224704544/1286074409177714708 Discord]. You will need to supply your file(s) for printing.
|}

==CNC - 3D Filament (FDM) Printers - [https://discord.com/channels/1270929620224704544/12709387556746732558 #3d-printing] on [[Discord]]==
3D printers using filament only require the canvas course, no in person authorization needed.
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[[ Prusa i3 3D printer]]
|[https://canvas.pumpingstationone.org/courses/60#Auths are online only through canvas].
|-
|[[ Creality Ender 3 A 3D Printer]]
|[https://canvas.pumpingstationone.org/courses/60#Auths are online only through canvas]. 3D printers using filament only require the canvas course.
|}

==Industrial CNC - [https://discord.com/channels/1270929620224704544/1270939130200850557 #cnc-general] on [[Discord]]==

==== ShopBot ====
There are 2 required classes for complete Shopbot Authorization. The first class is a software-only class to cover CNC concepts and the toolpath and control software. This class is unlimited capacity and generally open to the public. The software-only class is a prerequisite for the second class, the hands-on ShopBot authorization, which will be significantly shortened since it will only cover the specifics of the tool itself.

{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|'''Prerequisites'''
|'''Authorizer(s)'''
|-
|[[ShapeOko2 CNC Router]]
|2D and 3D Auths are scheduled 1:1
|None
|[[User:Newfatmike|Mike Thompson]]
|-
|-
|[[Shopbot PRS CNC router]]
|Regularly scheduled - check the [https://pumpingstationone.org/events/ Events Calendar]. There is also a helpful but not required [https://canvas.pumpingstationone.org/courses/69 Canvas course] going over the basics of 2D CAD using Inkscape.
| None
|David Earl
|-
|[[Tormach 1100 series CNC mill]]
|See the [https://canvas.pumpingstationone.org/courses/30 Canvas course] for authorization information
|Cold Metals general auth, Bridgeport auth
|[[User:Berky93|Alex Berkowitz]]
|}

==2D Printing - [https://discord.com/channels/1270929620224704544/1270938421476720641 #2d-printing] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|[https://wiki.pumpingstationone.org/wiki/Mimaki_CJV30-160 Mimaki CJV30-160]
|[https://canvas.pumpingstationone.org/courses/91 Complete the Canvas Course]
|-
|[[Epson Stylus Pro 9800 | Epson Stylus Pro 9800 Large-format Printer]]
|[https://wiki.pumpingstationone.org/Volunteer_Positions#2D_Printers Contact 2D Printing Area Host]
|}

==Graphic Arts & Textiles - [https://discord.com/channels/1270929620224704544/1270938360394809489 #arts-general] on [[Discord]]==
==== Sewing Machines ====
No certification is required for domestic sewing machines located under the big table.

{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|-
|Tier 1 Sewing Machines
|Check #sewing for upcoming auths
|-
|Leather Sewing Machines
|Check #sewing for upcoming auths
|-
|Embroidery Machine
|Check #embroidery for upcoming auths
|}
==Electronics - [https://discord.com/channels/1270929620224704544/1270933607011057776 #⚡-electronics-general] on [[Discord]]==

The Electronics area currently has no authorizations. However, the parts provided in Electronics aren't free. Please make a donation in the lockbox on the left side of the parts wall for anything you take.
==Kitchen - [https://discord.com/channels/1270929620224704544/1270938143948013699 #kitchen-general] on [[Discord]]==
{| class="wikitable"
|'''Machine/Area Name'''
|'''How to Schedule Authorization'''
|'''Prerequisites'''
|'''Authorizer(s)'''
|-
|[[Java Master 2002 Coffee Roaster]]
|Contact an authorizer to set up a time
|Acquire 1 lb green coffee beans, which can be done at [https://www.sweetmarias.com/ Sweet Maria’s]
|Ryan Pierce
|}

{{Template:ToolAuthorization
|authslug = hotairballoon
|authorization_name = Hot Air Balloon
|authorizer = [[User:Jane_hacker|Jane Hacker]]
|schedule_frequency = Twice a week, see Canvas
|discord_channel_link = https://discord.com/channels/1270929620224704544/1271319468055855165
|discord_channel_name = #aviation-club
|prerequisites = Completed auth for [[Parachute]]
|step1 = [https://canvas.pumpingstationone.org/courses/40 Complete the Canvas course]
|step2 = Use Canvas to schedule with the next available in-person auth
|step3 = Complete the in-person auth
|step4 =
|step5 =
|required_materials = Aviator goggles, cape, propane.
|notes = Will be rescheduled if there's bad weather.
}}

{| border="0" cellpadding="32" style="margin: 20px auto 20px auto; text-align:center;"
![[File:Authorization-required.png|alt=|center|328x328px]]
![[File:Figners-in-gears-sign.jpg|center|192x192px]]
|}

=New Tool Authorization Template=
Information for all authorizations will be maintained in this [[Authorizations]] page, and individual tool pages (or wherever else) can link back here. This creates one simple place to go and manage information regarding an auth without having to hunt down the individual tool or content on multiple pages.

Copy the example in [[Template:ToolAuthorization]] and paste it into this [[Authorizations]] page under the correct area/section, then fill out the needed fields. Once the page saves, above the filled out template there will be a <code><nowiki>{{#lst:Authorizations|authid}}</nowiki></code> code snippet specific for that filled out auth. Copy and paste this snippet into the tools page that requires the authorization. If you later need to update the auth information, return to this page and edit it here.
==Sample Template Code==
<pre>{{Template:ToolAuthorization
|authslug = hotairballoon
|authorization_name = Hot Air Balloon
|authorizer = [[User:Jane_hacker|Jane Hacker]]
|schedule_frequency = Twice a week, see Canvas
|discord_channel_link = https://discord.com/channels/1270929620224704544/1271319468055855165
|discord_channel_name = #random
|step1 = [https://canvas.pumpingstationone.org/courses/40 Complete the Canvas course]
|step2 = Use Canvas to schedule with the next available in-person auth
|step3 = Complete the in-person auth
|description = Please remember to bring aviator goggles and propane
}}</pre>
==Example:==

__FORCETOC__
__NOEDITSECTION__

Juki-LS-341-Cylinder-Arm-Sewing-Machine

2024-08-18T01:30:00Z

Ugrosse:

{{Template:EquipmentPage
|owner = Uwe Grosse
|hostarea = Arts
|certification = yes
|hackable = No
|model = Juki LS-341
|serial = LS0VM05330
|arrived = 5/1/2023
|where = Arts
|doesitwork = yes
|contact = @UweGrosse
|value = $2,000
|image = JUKI-LS-341.jpeg
}}PDF Manual: [[:File:Juki_LS-341N_InstructionManual.pdf|Juki LS-341N Manual]]

Category:Arts

2024-08-18T01:28:13Z

Ugrosse: /* Tools Available */

{{Infobox HostedArea
| image = Equipment-no-photo.jpg
| areaname = Arts - Graphic Arts and Textiles
| hostedsince =
| location = Second Floor
| toolcategory =
| hostname = Lydia Miller
| hostphone =
| hostemail =art@pumpingstationone.org
| hostother = @arts on Slack
| hosthours =
| hostcerts =
}}

== Rules ==

Please put supplies and tools back when you are done. Fabric cutting scissors are for use on cloth fabric and thread only. Members are welcome to use all donated materials such as beads, fabric, thread, and yarn in the space.

== Safety ==

== Tools Available ==
* [[Singer 20U Industrial Sewing Machine]]
* [[Sears Kenmore Model 158.18130 Sewing Machine]]
* [[J.C.Penney Free Arm Sewing Machine]]
* [[Singer Serger 14T948DS|Singer cutting serger [interlock] machine]]
* [[Consew 287RB Industrial Sewing Machine]]
* [[CowBoy CB3200 Leather Stitcher|CowBoy CB3200 Heavy Duty Leather Stitcher]] (w/ Flatbed Attachment)
* Adler 30-1 Shoe Patcher Sewing Machine (Shoe Patcher, Repair Work)
* [[Juki-LS-341-Cylinder-Arm-Sewing-Machine|Juki LS-341 Cylinder Arm Sewing Machine]] (w/ Flatbed attachment)
* Steam iron and ironing board, small [sleeve] ironing board, tailor's ham, ham holder
* [[Gravity Iron]]
* Large 8' fabric table
* Small table-top weaving loom, inkle frame loom, warping board, and assorted wooden yarn winders, hand crank yarn winder
* Knitting and crochet needles, Knifty Knitter plastic hoop style knitting looms
* Cricut paper cutter
* Large printmaking drying rack and lighted bench
* Airbrush tools and compressor
* Guillotine paper cutter
* A-Frame wooden easel; small aluminum table top easel
* Silkscreens and squeegees; t-shirt printing machine
* Leather tooling hand tools
* Ball peen hammer
* Hot glue gun
* Staple guns
* Small lamination machine
* 3-Hole punch
* Cutting mat and Xacto knife

== Wish List ==

== Certifications ==

[[Category:Hosted Areas]]
[[Category:Member Manual]]
[[Category:Equipment]]
[[Category:Projects]]
[[Category:Tutorials]]

Juki-LS-341-Cylinder-Arm-Sewing-Machine

2024-08-18T01:27:35Z

Ugrosse: Created page with "{{Template:EquipmentPage |owner = Uwe Grosse |hostarea = Arts |certification = yes |hackable = No |model = Juki LS-341 |serial = SERIAL NUMBER |arrived = 5/1/2023 |where = Art..."

{{Template:EquipmentPage
|owner = Uwe Grosse
|hostarea = Arts
|certification = yes
|hackable = No
|model = Juki LS-341
|serial = SERIAL NUMBER
|arrived = 5/1/2023
|where = Arts
|doesitwork = yes
|contact = @UweGrosse
|value = $2,000
|image = JUKI-LS-341.jpeg
}}PDF Manual: [[:File:Juki_LS-341N_InstructionManual.pdf|Juki LS-341N Manual]]

File:Juki LS-341N InstructionManual.pdf

2024-08-18T01:26:05Z

Ugrosse:

File:JUKI-LS-341.jpeg

2024-08-18T01:23:42Z

Ugrosse: Juki LS-341 Cylinder arm sewing machine

== Summary ==
Juki LS-341 Cylinder arm sewing machine

CowBoy CB3200 Leather Stitcher

2024-05-15T17:52:48Z

Ugrosse:

{{Template:EquipmentPage
|owner = Uwe Grosse
|hostarea = Arts
|certification = yes
|hackable = No
|model = CowBoy CB3200
|serial = SERIAL NUMBER
|arrived = 5/1/2024
|where = Arts
|doesitwork = yes
|contact = @UweGrosse
|value = $2,500
|image = CowBoyCB3200.jpeg
}}PDF Manual: [[:File:CB3200Manual.pdf|CowBoy CB3200 Manual]]

How to install the Flatbed Table Attachment:
https://www.youtube.com/watch?v=Dn1Z0zgVZ40

CowBoy CB3200 Leather Stitcher

2024-05-15T17:39:40Z

Ugrosse: Added manual link

{{Template:EquipmentPage
|owner = Uwe Grosse
|hostarea = Arts
|certification = yes
|hackable = No
|model = CowBoy CB3200
|serial = SERIAL NUMBER
|arrived = 5/1/2024
|where = Arts
|doesitwork = yes
|contact = @UweGrosse
|value = $2,500
|image = CowBoyCB3200.jpeg
}}Manual: [[:File:CB3200Manual.pdf|CowBoy CB3200 Manual]]

Category:Arts

2024-05-15T17:38:09Z

Ugrosse: Fixed link

{{Infobox HostedArea
| image = Equipment-no-photo.jpg
| areaname = Arts - Graphic Arts and Textiles
| hostedsince =
| location = Second Floor
| toolcategory =
| hostname = Lydia Miller
| hostphone =
| hostemail =art@pumpingstationone.org
| hostother = @arts on Slack
| hosthours =
| hostcerts =
}}

== Rules ==

Please put supplies and tools back when you are done. Fabric cutting scissors are for use on cloth fabric and thread only. Members are welcome to use all donated materials such as beads, fabric, thread, and yarn in the space.

== Safety ==

== Tools Available ==
* [[Singer 20U Industrial Sewing Machine]]
* [[Sears Kenmore Model 158.18130 Sewing Machine]]
* [[J.C.Penney Free Arm Sewing Machine]]
* [[Singer Serger 14T948DS|Singer cutting serger [interlock] machine]]
* [[Consew 287RB Industrial Sewing Machine]]
* [[CowBoy CB3200 Leather Stitcher|CowBoy CB3200 Heavy Duty Leather Stitcher]] (w/ Flatbed Attachment)
* Adler 30-1 Shoe Patcher Sewing Machine (Shoe Patcher, Repair Work)
* Juki LS-341 Cylinder Arm Sewing Machine (w/ Flatbed attachment)
* Steam iron and ironing board, small [sleeve] ironing board, tailor's ham, ham holder
* [[Gravity Iron]]
* Large 8' fabric table
* Small table-top weaving loom, inkle frame loom, warping board, and assorted wooden yarn winders, hand crank yarn winder
* Knitting and crochet needles, Knifty Knitter plastic hoop style knitting looms
* Cricut paper cutter
* Large printmaking drying rack and lighted bench
* Airbrush tools and compressor
* Guillotine paper cutter
* A-Frame wooden easel; small aluminum table top easel
* Silkscreens and squeegees; t-shirt printing machine
* Leather tooling hand tools
* Ball peen hammer
* Hot glue gun
* Staple guns
* Small lamination machine
* 3-Hole punch
* Cutting mat and Xacto knife

== Wish List ==

== Certifications ==

[[Category:Hosted Areas]]
[[Category:Member Manual]]
[[Category:Equipment]]
[[Category:Projects]]
[[Category:Tutorials]]

CowBoy CB3200 Leather Stitcher

2024-05-15T17:36:38Z

Ugrosse: Added manual link

{{Template:EquipmentPage
|owner = Uwe Grosse
|hostarea = Arts
|certification = yes
|hackable = No
|model = CowBoy CB3200
|serial = SERIAL NUMBER
|arrived = 5/1/2024
|where = Arts
|doesitwork = yes
|contact = @UweGrosse
|value = $2,500
|image = CowBoyCB3200.jpeg
}}Manual: [[CowBoy CB320 Manual|CowBoy CB3200 Manual]]

CowBoy CB3200 Leather Stitcher

2024-05-15T17:34:34Z

Ugrosse:

File:CowBoyCB3200.jpeg

2024-05-15T17:30:51Z

Ugrosse:

CowBoy CB3200 Leather Stitcher

2024-05-15T17:29:22Z

Ugrosse: Created page with "{{Template:EquipmentPage |owner = Uwe Grosse |hostarea = Arts |certification = yes |hackable = No |model = CowBoy CB3200 |serial = SERIAL NUMBER |arrived = 5/1/2024 |where = A..."

{{Template:EquipmentPage
|owner = Uwe Grosse
|hostarea = Arts
|certification = yes
|hackable = No
|model = CowBoy CB3200
|serial = SERIAL NUMBER
|arrived = 5/1/2024
|where = Arts
|doesitwork = yes
|contact = @UweGrosse
|value = $2,500
|image = "IMAGENAME.JPG" (case sensitive, this is whatever you named the image when you uploaded it)
}}

File:CB3200Manual.pdf

2024-05-15T16:56:53Z

Ugrosse:

Category:Arts

2024-05-12T00:44:28Z

Ugrosse: /* Tools Available */

{{Infobox HostedArea
| image = Equipment-no-photo.jpg
| areaname = Arts - Graphic Arts and Textiles
| hostedsince =
| location = Second Floor
| toolcategory =
| hostname = Lydia Miller
| hostphone =
| hostemail =art@pumpingstationone.org
| hostother = @arts on Slack
| hosthours =
| hostcerts =
}}

== Rules ==

Please put supplies and tools back when you are done. Fabric cutting scissors are for use on cloth fabric and thread only. Members are welcome to use all donated materials such as beads, fabric, thread, and yarn in the space.

== Safety ==

== Tools Available ==
* [[Singer 20U Industrial Sewing Machine]]
* [[Sears Kenmore Model 158.18130 Sewing Machine]]
* [[J.C.Penney Free Arm Sewing Machine]]
* [[Singer Serger 14T948DS|Singer cutting serger [interlock] machine]]
* [[Consew 287RB Industrial Sewing Machine]]
* CowBoy CB3200 Heavy Duty Leather Stitcher (w/ Flatbed Attachment)
* Adler 30-1 Shoe Patcher Sewing Machine (Shoe Patcher, Repair Work)
* Juki LS-341 Cylinder Arm Sewing Machine (w/ Flatbed attachment)
* Steam iron and ironing board, small [sleeve] ironing board, tailor's ham, ham holder
* [[Gravity Iron]]
* Large 8' fabric table
* Small table-top weaving loom, inkle frame loom, warping board, and assorted wooden yarn winders, hand crank yarn winder
* Knitting and crochet needles, Knifty Knitter plastic hoop style knitting looms
* Cricut paper cutter
* Large printmaking drying rack and lighted bench
* Airbrush tools and compressor
* Guillotine paper cutter
* A-Frame wooden easel; small aluminum table top easel
* Silkscreens and squeegees; t-shirt printing machine
* Leather tooling hand tools
* Ball peen hammer
* Hot glue gun
* Staple guns
* Small lamination machine
* 3-Hole punch
* Cutting mat and Xacto knife

== Wish List ==

== Certifications ==

[[Category:Hosted Areas]]
[[Category:Member Manual]]
[[Category:Equipment]]
[[Category:Projects]]
[[Category:Tutorials]]